Gigabyte GA-MA790FXT-UD5P Thread

**Racpu_** · 03-21-2009, 10:15 AM

To me the LH64A with Vista64 Ultimate not working I do not know why.

If you choose LH64A not load the drivers but if you click the folder already gives LH, and detects the RAID and I can install windows, but after installing, when you restart the first time gives BSOD ...

Someone knows what could be?

**keenan** · 03-21-2009, 10:20 AM

Is your installation source (DVD-RW) ATA or SATA...?

**Racpu_** · 03-21-2009, 10:25 AM

Sata

**keenan** · 03-21-2009, 10:27 AM

Ok, now I take it you DVD-RW is connected to one of the white SATA ports..?

Look at the screenshot above, is that the settings you use..?

**Racpu_** · 03-21-2009, 10:39 AM

Ok .. thanks for the config in the bios, I try ...

If not I will test Windows 7 X64 ...

**Racpu_** · 03-21-2009, 10:45 AM

Originally Posted by keenan

Ok, now I take it you DVD-RW is connected to one of the white SATA ports..?

Look at the screenshot above, is that the settings you use..?

The DVD-RW is connected in Blue SATA ports, i change to white...

I do not see what the problem is, only if the Realease of my Windows Vista ...

After testing the Win7 I see ...

**bro20000** · 03-21-2009, 10:45 AM

If your testing windows 7 64 i recommend using version 7057 seems alot faster than the rest!

**Racpu_** · 03-21-2009, 10:48 AM

Yes, I tested the version RC1.Build.7057.x64...

**shaolin95** · 03-21-2009, 11:11 AM

I got 7048 right now...can upgrade to 7057 or do I need to reinstall everything?

**keenan** · 03-21-2009, 11:40 AM

I think you're gonna have to reinstall...

**bro20000** · 03-21-2009, 11:52 AM

Reinstall the best option mate!

**shaolin95** · 03-21-2009, 02:40 PM

Argh that sucks...I hate reinstalling all over again....good thing Ihvent dont much with W7 anyway.
BTW guys two questions.

#1 Does OCing the HT Link does anything for performance?
#2 What is OCing the IMC (Integrated memory controller)? I saw a "guide" for Phenom overclocking and it claims that second to increasing the multiplier, ocing the IMC gives the biggest boost in performance.

**Racpu_** · 03-22-2009, 05:38 AM

Now fix the problem of windows with Win7 x64 has to install ...

Now I have a 3600Mhz CPU to 1.504V

My CPU Stepping is : "CACVC AC 0904EPMW"

Not much voltage?

Someone i can put the bios setup at the voltages?

Validate:

Tks...

**bro20000** · 03-22-2009, 05:51 AM

what N/B speed are you running at! And Voltage mate!

**Racpu_** · 03-22-2009, 06:06 AM

Speed is 2.4 NB

I put in bios +0.0725 V on NB

Check picture:

**yaxo11** · 03-22-2009, 06:14 AM

i have problem with et6, please help, also energy saver saying that the bioss version doesnt support energy saver, using F3B

**Racpu_** · 03-22-2009, 06:29 AM

My Config in Bios...

Is something wrong?

What changed?

Another thing is that I can increase the CPU Host Clock Control, it freezes.

Only in the multiplier ...

Someone a few tips ...

Thanks

**bro20000** · 03-22-2009, 08:18 AM

Try upping the mem Volts to say 1.8V and upping the cpu nb vid control to say 0.250V u should be able to get ur nb speed up to 2.8 then!

**Racpu_** · 03-22-2009, 08:25 AM

Is not stable, when i run Prime95 the PC restarts ...

What could it be?

**msimax** · 03-22-2009, 08:36 AM

did you check your memory, also what are your temps like?

**C0oL** · 03-22-2009, 08:47 AM

Just some info from my findings so far with the 720BE & UD5P...

Been trying for days to sort mine out, with virtually no success in OC'ing at all...

Initially, the board came with fb BIOS, and no matter what i tried over the stock 2.8Ghz, i would run into some problems when the system was busy or running a heavy application (No OC to memory, NB, etc) Then flashed to f3b, upped the volts a bit and tried unlocking the 4th core, which all resulted in Vista x64 not booting, and being none-repairable. Wiped the drive AGAIN and flashed to F3i, and all was fine @ stock, but as soon as i tried to OC, it would crash out time and time again, resulting in yet ANOTHER none-bootable Vista... Repeat the above with F4 Bios... As you can imagine, I was REALLY pulling my hair out.

Yesterday i flashed to f4g and wiped the hard drive.

Set the memory to 1600MHz 9-9-9-24 / 1.8v as specified got the USB drive out and booted into Memtest - which would fail after around 20 mins.
Dropped it to 1333MHz and I've ran a couple of hours without problems, so for some reason, my memory won't run at the quoted 1600Mhz

Any Ideas?

Then tried Windows 7 install, and while the system was installing it, i got allot of time where the system would seem to hang, or do nothing for 5 minutes, not even the HDD light would blink, and all of a sudden, the DVD drive would fire up and off we go. Any ideas?

Win7 Installed now, and takes less than 15 seconds to boot to desktop from leaving POST.

Tried x15 Multi @ stock volts and ran Prime (Blend) for a couple of hours, 3DM06 and further Memtests without problems so far....

Was doing all this till around 4am this morning, and today, i'm knackered, LOL.

Must have been a dodgy Vista Disc or something, as (touch wood) i seem to be having more success with Win7.

Your comments, views and suggestions are more than welcome. Chew* has been a star with the help, but i hate to keep pestering the same person all the time.

Deano

**msimax** · 03-22-2009, 08:53 AM

can u post picture of your mem timings in the bios

**bro20000** · 03-22-2009, 08:59 AM

Originally Posted by C0oL

Just some info from my findings so far with the 720BE & UD5P...

Been trying for days to sort mine out, with virtually no success in OC'ing at all...

Initially, the board came with fb BIOS, and no matter what i tried over the stock 2.8Ghz, i would run into some problems when the system was busy or running a heavy application (No OC to memory, NB, etc) Then flashed to f3b, upped the volts a bit and tried unlocking the 4th core, which all resulted in Vista x64 not booting, and being none-repairable. Wiped the drive AGAIN and flashed to F3i, and all was fine @ stock, but as soon as i tried to OC, it would crash out time and time again, resulting in yet ANOTHER none-bootable Vista... Repeat the above with F4 Bios... As you can imagine, I was REALLY pulling my hair out.

Yesterday i flashed to f4g and wiped the hard drive.

Set the memory to 1600MHz 9-9-9-24 / 1.8v as specified got the USB drive out and booted into Memtest - which would fail after around 20 mins.
Dropped it to 1333MHz and I've ran a couple of hours without problems, so for some reason, my memory won't run at the quoted 1600Mhz

Any Ideas?

Then tried Windows 7 install, and while the system was installing it, i got allot of time where the system would seem to hang, or do nothing for 5 minutes, not even the HDD light would blink, and all of a sudden, the DVD drive would fire up and off we go. Any ideas?

Win7 Installed now, and takes less than 15 seconds to boot to desktop from leaving POST.

Tried x15 Multi @ stock volts and ran Prime (Blend) for a couple of hours, 3DM06 and further Memtests without problems so far....

Was doing all this till around 4am this morning, and today, i'm knackered, LOL.

Must have been a dodgy Vista Disc or something, as (touch wood) i seem to be having more success with Win7.

Your comments, views and suggestions are more than welcome. Chew* has been a star with the help, but i hate to keep pestering the same person all the time.

Deano

Yeah windows 7 is alot better! What memory are you using in your system!

**Racpu_** · 03-22-2009, 09:09 AM

My memories are 2X2 GB Transcend DDR3 1333 MHz ..

The 1600Mhz 8-8-8-24 1T 1.6V not make mistakes, I think the problem is the CPU, maybe not a good batch, or is the bios ...

What Bios using?

Do not know what will ... any idea?

**C0oL** · 03-22-2009, 09:19 AM

Bro20000: I'm using 2x2Gb Corsair 1600Mhz (9-9-9-24 / 1.8v) Which is specified to work by Corsair....
MSIMax: Not at home to get a picture, but will get one ASAP...

Dean

Thread: Gigabyte GA-MA790FXT-UD5P Thread

Thread Tools

Search Thread

Rate This Thread

Display

Bookmarks

Bookmarks

Posting Permissions