Asus M3A79-T Deluxe

[Oliverda]

Yea I get the same thing with AOD, thats one thing I notice, Its the same thing with everest, but I do get a CPU reading that is right, just not the cores

Have you noticed any advantage on Phenom II OC when you turn the ACC on?

[HondaGuy]

Have you noticed any advantage on Phenom II OC when you turn the ACC on?

Since the new PII have them built in, I wonder by doing it this way through the bios over rides what is already built into these new chips?

I could never cold boot right up from bios with these settings before. I was able to reach them through AOD in windows

[charged3800z24]

Have you noticed any advantage on Phenom II OC when you turn the ACC on?

I get same clocks, regaurdless of ACC settings. But my chip OC's pretty good anyways. Might be same effect on Phenom 1. Where it helped the ones that don't OC as well.

[gOtVoltage]

I get same clocks, regaurdless of ACC settings. But my chip OC's pretty good anyways. Might be same effect on Phenom 1. Where it helped the ones that don't OC as well.

ACC Works exactly the same as the Beta701 for B3.

It may even be more stable.

Allows same High overclocks as preveouse 701.
Even the Supi 1m is the same speed as 701.

ATm i have not tried for 300HTT. All previose bioses are bugged with my 9950chip and will show 3800ghz after 293htt


0703 installed on first try and all voltages appear to be the same.

0701Beta



0703 Official



AOD 0703 ACC +4/ CPU TWEAK/ Idle 35c /Bios reads 34c @ 1.74vcpu/1.66vNb@2630

People with PHII should notice (stability and possiable higher Overclocks) when using higher NB/Ram settings.

This does perform better than the 0701Beta with B3 . I dont have a 940/945 yet. Do not expect a huge Oc increase with 0703 over the 0701 Beta if that what you had before,, its more or so tweaked for stability with PHII ACC SHOULD NOW WORK. If it dosnt at first try lower voltages with ACC(not Higher)

[Daveburt714]

FWIW, it seems pretty safe to turn ACC on using the 703 bios with a PhII. I've been playing with it for a few hours and haven't had to move the jumper yet... (much better than 603 bios!)

Here are the things I've noticed so far:

1) It does screw up the individual core temp display in AOD 2.1.4 (and HWMonitor), but the TIMPIN1 still works so you'll have an idea of the CPU temp...

2) Unlike the 9950 which liked positive numbers (+4/+6) the PhII likes negative numbers better (-4/-6). I started off raising the ACC and went all the way up to +8, but I had much better luck on the negative side. The side benefit of that was that even at higher V's the temps stayed lower (of course thats assuming TIMPIN1 is reliable)....

These are very preliminary results, and ACC is just as confusing as it was using the 9950 but at least it's safe to play with again...

Heres a SS of what I have so far.



Actual speed is 3.85, not sure why AOD shows current speed as 3.71. I can only assume Bios still needs a little more work...

BTW, I'm running 64bit Windows7 now, so take that into consideration as far as odd results are concerned. It runs pretty stable so I doubt that has anything to do with the wierd temp/speed results...

[MadDias]

seems as if u have to leave cpu vdda voltage at auto when using acc.
my temp reading in coretemp is now working with +2% acc.
when i used 2.8v cpu vdda i got that funny 0°C reading in coretemp.
0703 seems way more stable than any previous bios version.

[charged3800z24]

seems as if u have to leave cpu vdda voltage at auto when using acc.
my temp reading in coretemp is now working with +2% acc.
when i used 2.8v cpu vdda i got that funny 0°C reading in coretemp.
0703 seems way more stable than any previous bios version.

weird, I wonder if it is something else tho, I get 0 temp reading with VDDA on auto too.

[MadDias]

weird, I wonder if it is something else tho, I get 0 temp reading with VDDA on auto too.

me too now.. lol
must be something else.