DFI LANparty DK P45-T2RS/T3RS (Intel P45) - News|Info|Results

[DavidNJ]

The problem is that the divider 1:1 is the lowest, so if i want 4GHz RAM has to run 450MHz, and i have tryed down to 1.9V 5-5-5-15 with loose sub's It realy sucks!

Did i mention that my Ballistix do 600MHz 5-5-5-15 2.1V on my Commando, so it has to be mobo related.

No, it could be the variation of the memory chips on the sticks. Just like CPUs, they have different voltage/speed envelopes. In DDR3, with Intel current Core i7 voltage requirements they are binned for speed AND voltage. Some that do well at 2.1v, may draw more current than others, TTBOMYU.

[scooter.jay]

Finally got 1M done 600fsb more in the board i am sure just need to learn her tricks

[nikk]

nice one scooter, let's see some more

[TheGanG]

Good job bro!

[nullface]

Just tryed the "JRP45E8500+DDRII 1066_OCProfile_812BIOS" DFI ABS profile, with both my OCZ 8500 and Crucial 8500 (both D9MGH), all "banks" no go on both set's

EDIT: Not even my freaking Dominators at only 450MHz 5-5-5-15-5-42 will do!

[s e r e n i t y]

Hey guys,

Im having a few issue overclocking atm. Am trying to boot past 3.4GHZ on my Q6600 but PC doesnt post. PC is Prime95 stable at 9x356 (3.2GHZ) but at 372 fsb it crashes, whereas 371 fsb is fine :/?
I have tried both 812 and 1003 BIOS but no difference.

These are the settings I have been working with;

vCore - +100mV - +200mV)
vNB - 1.3v - 1.4v
vTT- 1.2v - 1.3v
vDIMM - 2.1
Multiplier - 9x
FSB - 356- 380
Timings - 5-5-5-13
Ram Frequency - 940mhz - 1115mhz
EIST - disabled
CIE - disabled

If anyone could give me a hand it would be greatly appreciated as I am at a total loss as to where to go

Cheers,
s e r e n i t y

[TheGanG]

Hey guys,

Im having a few issue overclocking atm. Am trying to boot past 3.4GHZ on my Q6600 but PC doesnt post. PC is Prime95 stable at 9x356 (3.2GHZ) but at 372 fsb it crashes, whereas 371 fsb is fine :/?
I have tried both 812 and 1003 BIOS but no difference.

These are the settings I have been working with;

vCore - +100mV - +200mV)
vNB - 1.3v - 1.4v
vTT- 1.2v - 1.3v
vDIMM - 2.1
Multiplier - 9x
FSB - 356- 380
Timings - 5-5-5-13
Ram Frequency - 940mhz - 1115mhz
EIST - disabled
CIE - disabled

If anyone could give me a hand it would be greatly appreciated as I am at a total loss as to where to go

Cheers,
s e r e n i t y

Try a High(est) FSB run please (with relaxed timings)
and PLL+/Vtt+/VCore+ for stable ocing too.

Don't let ram divider on auto.

[hawk999]

i just both DFi Lanprty DK p45-t2rs plus version

can u give me aq settings for overclocking my e7200 to 3.6ghz,3.8ghz and 4.0ghz

RIg sepcs
Da650
Team Xtreem ddr2-800 2gb
8800GT
e7200


tnx

[AnaMan]

mmm......nice combination yellow n orange.....

[firebane]

Hrm so I picked this board up for my e8600 and a few things.

1) I've updated bios to the latest
2) PCI-E slot #1 runs at 8x not 16x
3) This board is extremely finicky with overclocking. Where I could get 4.6 on my p45 Biostar I can barely break 4.3 on this guy.

[nullface]

Woo, just tryed the D113 Beta, and its not perfect but WAY better than D812 and DA07. (This is for JR P45)

[nikk]

Woo, just tryed the D113 Beta, and its not perfect but WAY better than D812 and DA07. (This is for JR P45)

how do you mean 'way better'?

[nullface]

RAM stability increased on my board. With D812 and DA07 i couldent OC for crap, my CPU was stable (Small FFTs) but my RAM failed badly not matter what. But now some (still not very impressive) stable RAM OC is possible

[firebane]

Can someone tell me if I'm asking to much from this board by trying 420x10?

I can't figure out if it doesn't like that high of a clock or I have a board with a deep hole around 420.

[nikk]

RAM stability increased on my board. With D812 and DA07 i couldent OC for crap, my CPU was stable (Small FFTs) but my RAM failed badly not matter what. But now some (still not very impressive) stable RAM OC is possible

what chips are on your ram mate?

[DemonsBlood]

hey i was wondering if the non plus version of this board is still good? I read somewhere they were defective of that sort?

[TheGanG]

hey i was wondering if the non plus version of this board is still good? I read somewhere they were defective of that sort?

"Plus + A3 Rev." is best choice (as a DFi P45 DDR2 board)

[AnaMan]

is that new rev.?....
coz i want to buy this board tomorow.......

[nullface]

what chips are on your ram mate?

I have tryed all my 3 sets, one pair of Ballistix 8500 "D9MGH" (they work the best, but not great), OCZ 8500 SLI Edition "D9MGH", and some Dominators 6400C4D "ProMOS".

But it is still hell to get them stable, i have found a "sweetspot" eventhoug it isent very sweet, at 450MHz 1:1 5-5-5-15-5-42, Performance lvl 9, 2.05V. Anything past that no go
With D812 and DA07 i couldent get ram stable at any overclock only at default BIOS settings. Volts and timings didnt make any difference at all, but im not very much into the sub's, other than waht i mentioned abov.

My CPU is stable Small FFTs stable at up to 500FSB (havent testet further, as im just looking for a good 24/7 OC).

[p4spooky]

Guys: Playing with DFI X48-T2RSB Plus (Latest Beta Bios - C24 12/24/08).

With VDroop Enable:

Bios: 1.375
Idle: 1.38
Load: 1.328

With VDroop Disable:

Bios: 1.375
Idle: 1.38
Load: 1.344

This appears to be flipped or is my understanding of this setting incorrect. My chip needs 1.34 to be stable at 450FSB on P5Q Pro (Needs 1.34 under load). I am able to hit this on the DFI but I have to Disable Vdroop to be stable.

Did any one else having this issue or something is wrong with the board?

[TheGanG]

We have a new Air Test, E8600 with Xigma Achilles + 60 Cfm TT Fan, DFi DK P45 T2RS, Very low ambient.

S-Pi 1M: 9,265 Sn at 5091 MHz, Max: 5123 MHz, Boot: 4800 MHz.

[nullface]

My OCZ that wont do anything on my JR are even on the official supported ram list "OCZ2N1066SR2GK"

[DenSky]

There is such problem: when I load a video card with game or the program (Video Card Stability Test, OCCT) occurs a procorf on 12в to 11.47 ~11.55 volt. But if to connect FDD конектор for an additional food of a video card that more low 11.90 not просаживается. FSP Epsilon 800W. The Same situation was with GA-p35-dq6. Thought that the block (Corsair tx 650W) has changed on FSP and all too most.If not to connect FDD power supply and will come in BIOS into value "12V" 11.77v. If will include FDD "12V" 12.03v

[TheGanG]

New CPU, latest tests:

Freq: 4510.91 MHz (501.21 * 9)

DFi LP DK P45-T2RS PLUS
Q9650
Crucial Ballistix Tracer 800 MHz
Kingston Hyperx 1066 MHz
ATI Radeon X1550 128 MB > a few WRs
High Power 1000 W

Validation: 4510.91 MHz (Max-Air)
http://valid.canardpc.com/show_oc.php?id=499345

Validation: 4259.71 MHz (2D/3D)
http://valid.canardpc.com/show_oc.php?id=499985

-S-Pi 1M: 10,969 sn.


-S-Pi 32M: 12.03,281 sn.


-Pi Fast: 22,17 sn.


-WPrime 32M: 10,172 sn


-WPrime 1024M: 320,36 sn.

[angoholic]

omg fsb470



Quad OC with this Board is not as good as the UD3P or R, FSB510 Prime Large stable is the Maximum.