Live MB OC Report :: ASUS Rampage Extreme

[Gullo92]

Hi I have a quad and 4x1gb, And I cant seem to rum memtst without errors above 1600Mhz, above that i get alway the test 5 error between stick 0 and stick 1, allthe other test run fine, the problem that i think is moving blocks between channels.

with 2x1gb i can reach 1900Mhz with my cellshock 1800.

Yes the problem is the 4gb.

Now I'm runing 3.80Ghz, and my mems are at 1425 1.9v 8-7-6-21, 1T

here is my config:

AI OVERCLOCK TUNER ==================== MANUAL
OC FROM CPU LEVEL ==================== AUTO
OC FROM MEMORY LEVEL UP ============== AUTO
FSB FREQUENCY ======================= 475
CPU RATIO SETTING ==================== 08
CPU CONFIGURATION
CPU CLOCK SKEW ====================== AUTO
NB CLOCK SKEW ======================= AUTO
FSB STRAP TO NORTH BRIDGE ============= 400
PCIE FREQUENCY ====================== 100
DRAM FREQUENCY ===================== 1425
DRAM COMAND RATE =================== 1N
DRAM TIMING CONTROL ================= MANUAL
CAS LATENCY ======================== 8
RAS TO CAS DELAY ==================== 7
RAS PRE TIME ======================== 6
RAS ACT TIME ======================= 21
RAS TO RAS DELAY =================== Auto
REF CYCLE TIME ===================== 72
WRITE RECOVERY TIME ================ Auto
READ TO PRE TIME =================== Auto
READ TO WRITE DELAY S/D ============= Auto
WRITE TO READ DELAY S =============== Auto
WRITE TO READ DELAY D =============== Auto
READ TO READ DELAY S ================ Auto
READ TO READ DELAY D ================ Auto
WRITE TO WRITE DELAY S ============== Auto
WRITE TO WRITE DELAY D ============== Auto
WRITE TO PRE DELAY ================== Auto
READ TO PRE DELAY=================== Auto
PRE TO PRE DELAY==================== Auto
ALL PRE TO ACT DELAY================= Auto
ALL PRE TO REF DELAY================= Auto
DRAM STATIC READ CONTROL =========== DISABLED
DRAM DYNAMIC WRITE CONTROL ========= DISABLED
DRAM SKEW CONTROL ================= Auto
AI CLOCK TWISTER =================== AUTO
AI TRANSACTION BOOSTER ============= AUTO
EPU II PHASE CONTROL =============== AUTO
CPU VOLTAGE ====================== 1.38750
LOAD-LINE CALIBRATION ============== ENABLED
CPU PLL VOLTAGEM ================== 1.56406
FSB TERMINATION VOLTAGEM ========== 1.33866
CPU GTLVREF 0 ===================== +80
CPU GTLVRED 1 ===================== +40
CPU GTLVRED 2 ===================== +80
CPU GTLVRED 3 ===================== +40
NB GTLVRED ======================= +40
NORTH BRIDGE VOLTAGE ============== 1.51
DRAM VOLTAGEM ==================== 1.90
NB DDRVREF ======================== AUTO
DDR3 CHANNEL A VREF ================ AUTO
DDR3 CHANNEL B VREF ================ AUTO
SOUTH BRIDGE 1.5 VOLTAGE =========== 1.51106
SOUTH BRIDGE 1.05 VOLTAGE ========== 1.06039
CPU SPREAD SPRECTRUM ============== DISABLED
PCIE SPREAD SPECTRUM ============== DISABLED

ADVANCED
CPU CONFIGUTION
CPU RATION SETTING ================= 08
C1E SUPORT ======================== DISABLED
CPU TM FUNCTION =================== DISABLED
MAX CPUID VALUE LIMIT =============== DISABLED
VANDERPOOL TECHNOLOGY ============= ENABLED
EXECUTE DISABLED BIT ================ DISABLED
CORE MULTI- PRECESSING ============== ENABLED

can you post the settings with 2x1gb ram 1900 mhz?

[aln688]

FYI for anyone that's going to try, the Thermalright HR-05 SLI/IFX when used on the SB (Southbridge) on this board will not allow you to install a double wide graphics card. I installed the HR-05 SLI/IFX and realized the screw that goes through from the bottom of the board sticks up tall enough to hit the underside of a graphics card, such as a GTX 280/4870 X2.



...and...



Any suggestions for a SB heatsink? I'm looking at the Enzotech CNB-S1L (fanless), but the spacings on the push-pins don't go straight into the board. What I'm thinking of doing is filing off the "arms" on the CNB-S1L and using 3M 8815 thermal tape to secure the copper heatsink to the SB chip.

http://www.performance-pcs.com/catal...ducts_id=22980

This tape is the same thermal tape used on Enzotech's BMR-C1 copper MOSFET heatsinks. Performance PC's sells a 2"x2" square of this tape for $2.95. Anyone think this will work, or have any alternative ideas?

Thanks.

[mrcape]

FYI for anyone that's going to try, the Thermalright HR-05 SLI/IFX when used on the SB (Southbridge) on this board will not allow you to install a double wide graphics card. I installed the HR-05 SLI/IFX and realized the screw that goes through from the bottom of the board sticks up tall enough to hit the underside of a graphics card, such as a GTX 280/4870 X2.

Here's what I did with the other mounting nuts -

RE cooling replace

It's kinda hard to see but I used the J hooks.

[aln688]

Here's what I did with the other mounting nuts -

RE cooling replace

It's kinda hard to see but I used the J hooks.

It's odd as your board looks very similar to my own, referring to the copper heatsinks at the NB area, the Enzotech MST-81's and NB heatsink. It is a little difficult to see the hooks you used in that photograph.

Also noticed, your Enzotech MST-81's, did you use something other than push-pins to mount them? It looks like you used a similar M3 thumb screw as the HR-05 uses.

[rob2k]

It is a little difficult to see the hooks you used in that photograph.

Hi Aln688, the hooks should have came with the heatsink like in the middle of the picture below.......

just place the hook end over the fixing brkt and tighten the nuts from the underside of the board. Should save you some cash

[aln688]

Hi Aln688, the hooks should have came with the heatsink like in the middle of the picture below.......

just place the hook end over the fixing brkt and tighten the nuts from the underside of the board. Should save you some cash

Hello Rob2k, Happy New Year! Shouldn't your handle be Rob2kIX? Just joking.

That's odd, I never had hooks in my package and I never had the same brackets are in your picture, I only had a straight bracket and a slightly bent one at either end, which I couldn't use as it wouldn't go over the screws.

I've already ordered the CNB-S1L, but thanks anyway. When I get it I'm going to try and file off the "arms" and make the heatsink a perfect square, then apply the 3M 8815 thermal tape on the back and stick it to the SB.

Certainly a lot of copper on this board now...

[rob2k]

Hello Rob2k, Happy New Year! Shouldn't your handle be Rob2kIX? Just joking.

I've already ordered the CNB-S1L, but thanks anyway. When I get it I'm going to try and file off the "arms" and make the heatsink a perfect square, then apply the 3M 8815 thermal tape on the back and stick it to the SB.

Certainly a lot of copper on this board now...

Happy New Year to you too .... thought you had an extended Christmas hols

Guess they must have removed the hooks for cost saving !, the thermal tape should work well but as the SB chip is smaller than the CNS-S1L it might be worth leaving the legs on at first to test the tape or future use on another board. Your build is looking good

[Gullo92]

Hi Aln688, the hooks should have came with the heatsink like in the middle of the picture below.......

just place the hook end over the fixing brkt and tighten the nuts from the underside of the board. Should save you some cash

i saw that you post new settings with qx9770 can you post your new settings please?
thanks

gullo92

[mrcape]

It's odd as your board looks very similar to my own, referring to the copper heatsinks at the NB area, the Enzotech MST-81's and NB heatsink. It is a little difficult to see the hooks you used in that photograph.

Also noticed, your Enzotech MST-81's, did you use something other than push-pins to mount them? It looks like you used a similar M3 thumb screw as the HR-05 uses.

Yeah I used some EK backplates and some screws from an old gpu pot.