DFI Lanparty UT P45-T2RS Banter starts here!!!

[prostoman]

Finally, I got the goods. But there are always problems, always something in the way. Missing a DVI/VGA converter and only have a stock cooler that is almost sitting there because of its own weight. Cant get it in place because I cant remove the backplate from my water setup (super strong glue back there)

Still, I got good results with temps goin no higher than 75'C and really cramped space and getto solutions for a lot of problems (will take a oic some day, lol)

I am not finished yet, and I know this will kick ass under water when I get back home after holidays (on the move with all the parts right now) 5GHz is with in my reach

[SNiiPE_DoGG]

Went to beta BIOS and got a nice surprise


4.325 -- 480x9 and shes got plenty more where that came from
1.376vCore
http://valid.canardpc.com/show_oc.php?id=464589

[SOXX]

Hello,

the DFI is a very nice board. I test a Q9550 at FSB 470, it was very hard to be stable. FSB 500 is to heavy at the moment!

FSB 470 looks very nice:



Can anyone give my Tips for get FSB 500 stable?

Sorry for my bad english, i leave the scool for 10 years ago !

[SNiiPE_DoGG]

raise your vtt voltage to ~1.35 and you will reach higher FSB

[SOXX]

I test it this weekend, VTT 1,35 is very high.

Anyone know when DFI release a new Bios?

[SNiiPE_DoGG]

I test it this weekend, VTT 1,35 is very high.

Anyone know when DFI release a new Bios?

not really at all. some run up to 1.5vtt 24/7

I dont believe it to be dangerous. I've been benching this weekend with 1.55VTT

[SOXX]

OK, i will test it. My rig runs 24/7 with the settings in the screen, I think thats a very nice result.

[emoners]

anybody tried running crossfire on this board? i've seen a lot of people running crossfire on the JR counterpart, maybe this board can do better?

[SNiiPE_DoGG]

anybody tried running crossfire on this board? i've seen a lot of people running crossfire on the JR counterpart, maybe this board can do better?

I'm doing 4870x2 + 4870 512mb benching as we speak

heres the first result http://service.futuremark.com/compare?3dm06=9268247

[emoners]

thanks SNiiPE_DoGG...any issues with that combo (4870x2 + 4870)? which lanes are you using by the way?

[SNiiPE_DoGG]

thanks SNiiPE_DoGG...any issues with that combo (4870x2 + 4870)? which lanes are you using by the way?

using 8x8, havent played games on the test bench so I cant say if theres an issue

[SNiiPE_DoGG]

heres the vantage trifire result, I pleased with it and I havent even voltmodded the x2 yet

http://service.futuremark.com/compare?3dmv=604646

[zsamz_]

I'm doing 4870x2 + 4870 512mb benching as we speak

heres the first result http://service.futuremark.com/compare?3dm06=9268247

nice
does it perform close to 3 4870s ?
you sick makin me wanna do trifire

[SNiiPE_DoGG]

nice
does it perform close to 3 4870s ?
you sick makin me wanna do trifire

never used 3 4870s so I dont have a comparison, I can tell you though that the trifire is extra broken in extreme vantage preset, I only scored x5950 lololol

[DoObs]

Hey guys

Is it worth selling my Biostar I45 and getting the DFI LP DK P45-T2RS(ABS) Intel P45 Chipset OR if i can, get the DFI LP UT P45-T2RS

[emoners]

@SNiiPE_DoGG: what's your settings on that Quad?

[SNiiPE_DoGG]

@SNiiPE_DoGG: what's your settings on that Quad?

I'll get you a full bios template in like ~4 hours

[Gogeta]

Are these boards still being sold in the US? I'm not seeing any results for the UT variant on Froogle and Newegg has deactivated their listing.

Edit: Referring to the T2RS. I remember similar activity with retail inventory when the X48/X38-T2R were released. Hopefully this is the same deal.

[SNiiPE_DoGG]

Are these boards still being sold in the US? I'm not seeing any results for the UT variant on Froogle and Newegg has deactivated their listing.

very odd. I bought mine last week.....

You might want to call motherboard pro and ask them, they definitely will have the inside scoop on this situation.

[SNiiPE_DoGG]

Full BIOS template for the beta bios on the
P45 T3RS

Note: not fully prime stable, 3D and OCCT 1hr stable

>CPU Feature:
 
Thermal Management Control.......... - Disabled
PPM(EIST) Mode...................... - Disabled
Limit CPUID MaxVal.................. - Disabled
CIE Function........................ - Disabled
Execute Disable Bit................. - Enabled
Virtualization Technology........... - Enabled
Core Multi-Processing............... - Enabled
 
>DRAM Timing:
 
Enhance Data transmitting........... - Fast
Enhance Addressing.................. - Fast
T2 Dispatch......................... - Disabled

>Clock Setting Fine Delay Press Enter:

DLL And RCOMP Settings.............. - Manual
Ch1 Dram Defaul Skew................ - Model 1
Ch2 Dram Defaul Skew................ - Model 1
RCOMP Settings...................... - Model 1

Fine Delay Step Degree.............. - 70ps

Ch1 Clock Crossing Setting.......... - Agressive
DIMM1 Clock Fine Delay.............. - Current[1346ps]
DIMM2 Clock Fine Delay.............. - Current[1346ps]
Ch1 Control0 Fine Delay............. - Current[166ps]
Ch1 Control1 Fine Delay............. - Current[166ps]
Ch1 Control2 Fine Delay............. - Current[124ps]
Ch1 Control3 Fine Delay............. - Current[110ps]
Ch1 Command Fine Delay.............. - Current[262ps]

Ch2 Clock Crossing Setting.......... - Agressive
DIMM3 Clock Fine Delay.............. - Current[1346s]
DIMM4 Clock Fine Delay.............. - Current[1346ps]
Ch2 Control0 Fine Delay............. - Current[14ps]
Ch2 Control1 Fine Delay............. - Current[56ps]
Ch2 Control2 Fine Delay............. - Current[0ps]
Ch2 Control3 Fine Delay............. - Current[0ps]
Ch2 Command Fine Delay.............. - Current[110ps]

Ch1 Ch2 Common Clock Setting........ - Auto

Ch1 RDCAS GNT-Chip Delay............ - Auto
Ch1 WRCAS GNT-Chip Delay............ - Auto
Ch1 Command To CS Delay............. - Auto
.
Ch2 RDCAS GNT-Chip Delay............ - Auto
Ch2 WRCAS GNT-Chip Delay............ - Auto
Ch2 Command To CS Delay............. - Auto

Flex Memory Mode..................... - Auto
Common CMD to CS Timing.............. - 2N
CAS Latency Time (tCL)............... - 7
RAS# to CAS# Delay (tRCD)............ - 8
RAS# Precharge (tRP)................. - 8
Precharge Delay (tRAS)............... - 22
All Precharge to Act................. - Auto
REF to ACT Delay (tRFC).............. - Auto
Performance Level.................... - 8

>Read delay phase adjust Press Enter:

Channel 1 Phase 0 Pull-In........... - Auto
Channel 1 Phase 1 Pull-In........... - Auto
Channel 1 Phase 2 Pull-In........... - Auto
Channel 1 Phase 3 Pull-In........... - Auto
Channel 1 Phase 4 Pull-In........... - Auto

Channel 2 Phase 0 Pull-In........... - Auto
Channel 2 Phase 1 Pull-In........... - Auto
Channel 2 Phase 2 Pull-In........... - Auto
Channel 2 Phase 3 Pull-In........... - Auto
Channel 2 Phase 4 Pull-In........... - Auto

Write to PRE Delay (tWR)............ - Auto
Rank Write to Read (tWTR)........... - Auto
ACT to ACT Delay (tRRD)............. -Auto
Read to Write Delay (tRDWR)......... - Auto
Ranks Write to Write (tWRWR)........ - Auto
Ranks Read to Read (tRDRD).......... - Auto
Ranks Write to Read (tWRRD)......... - Auto
ALL PRE to Refresh.................. - Auto

>Voltage Settings:

CPU VID Control..................... - 1.25V
CPU VID Special Add................. - Disabled
CPU VID Special Add................. - 113.22%
DRAM Voltage Control................ - 1.87v
SB Core/CPU PLL Voltage............. - 1.75v
NB Core Voltage..................... - 1.55v (1.47v actual)
CPU VTT Voltage..................... - 1.58v
Vcore Droop Control................. - Disabled
Clockgen Voltage Control............ - 3.45v
GTL+ Buffer Strength................ - Strong
CPU GTL 0 REF Volt.................. - 0.6725
CPU GTL 2 REF Volt.................. - 0.6725
CPU GTL 1 REF Volt.................. - 0.6725
CPU GTL 3 REF Volt.................. - 0.6725
North Bridge GTL 0 REF Volt......... - 0.6750
North Bridge GTL 1 REF Volt......... - 0.6750
FSB Vref............................ - Auto
 
Genie BIOS Settings:
 
Exist Setup Shutdown................ - Mode 2
Exist Shutdown After AC loss........ - Enabled
AC Shutdown Free.................... - Enabled
O.C Clock Fail Retry Counter........ - 1
O.C Clock Fail CMOS Reloaded........ - Disabled
CPU Clock Ratio..................... - 9
Target CPU Clock.................... - 3800 MHz
CPU Clock........................... - 482
Boot Up Clock....................... - Auto

CPU Clock Amplitude................. - 900mV
CPU Clock0 Skew..................... - 100ps
CPU Clock1 Skew..................... - 100ps
DRAM Speed.......................... - 400/1066
Target DRAM Speed................... - 1284MHz
PCIE Clock.......................... - 101mhz

[DavidNJ]

How do you get that printout of BIOS settings?

[C-N]

How do you get that printout of BIOS settings?

You don't, its just made up in notepad.

Copy & paste the template into notepad & edit it with your settings.

Then to display them here on the thread type

[ code ] (without the spaces)

paste in your settings then type

[ /code ] (without the spaces)

[DavidNJ]

EK has waterblocks for the northbridge, southbridge, and power circuits, allowing you to remove the stock components and water cool. The northbridge and CPU Buck converter appears to run hot.

[SNiiPE_DoGG]

EK has waterblocks for the northbridge, southbridge, and power circuits, allowing you to remove the stock components and water cool. The northbridge and CPU Buck converter appears to run hot.

I will be completely watercooling this board, pics will be in my worklog in a few days

[SOXX]

My Board is complete under water!



The set is made in Germany by Mips Computer!