Asus M3A79-T Deluxe

[justapost]

NB@2580

http://img224.imageshack.us/img224/5514/sandraeb1.jpg, http://img228.imageshack.us/img228/9131/sandra2zo6.jpg, http://img228.imageshack.us/img228/7101/sandra3ov4.jpg

What was your HT speed? As gotVoltage mentioned a few times for higher NB speeds high HT speeds are a must. I can select above 2GHz here on the AsRock in the bios but at max 2GHz(10xmultis) are used.

BTW: LaingUltra leaked, shortened , burned a hole in my table and stopped working. Waiting for an D5 vario now.

[gOtVoltage]

What was your HT speed? As gotVoltage mentioned a few times for higher NB speeds high HT speeds are a must. I can select above 2GHz here on the AsRock in the bios but at max 2GHz(10xmultis) are used.

BTW: LaingUltra leaked, shortened , burned a hole in my table and stopped working. Waiting for an D5 vario now.

Dang ,,bummer

ALSO you can mod the D5 real easy for better flow

The D5's and or 655's are great little pumps...What works for great flow is drill the Inlet to !/2" ,, this will let the pump draw more volume from Resivior while keeping the same Head Preshure but with hihger flow. Its an easy 5min mod with a 1/2"drill bit.


On to the good stuff,,
As for Phenom Volts ,, i cant believe How much these things can take even with a stock heatsink.. The trick is to allow good volts but keep the temps in check.. Heat is the Number one ccause of Phenom failure along with the old IMC the B2's used. The B3's Handle Ram volts plus high NBvolts way better than the Old B2's.

For using 3.2-3.3ghz with 2400nb ..Even on Air (nonstock cooler) ive found that 1.48v -1.5volts works graet on the CPU/And NB with or with out ACC.

When you raise the Volts up you can use ACC in Munus mode -2 -4 aand so on to lower the overall volts Idle and Load although using higher manual settings for NB and Vcore..

It takes a lot of tweaking and all my Overclocks are done with high volts up to 3.3/3.4ghz and High NB just to see what it can do and watching my Temps . if its under the Max temp limit i lower the Volts a hair NB then go for Higher Clock values.. Ilways run the HT @ 2000 or Higher depending on My NB speed.

At high CPU clocks the NB @2000 -2200mhz can perform. Highe rCPu clocks along with low NBmhz do better than Low CPUclocks with HIGH NBmhz. Least thats what ive been seeing.


In the end its all realted to Heat ..Start stock with like 1.5volts for both CPU and NB and slowly raise the CPU to its highest level using just the Cpu Divider(multiX) with Stock NB..

yOu should be able to reach 3.2ghz with a decent air cooler and even the stock one on B3 9850/9950. Default VID is 1.55 for both CPU and NB .

Even My TA770 was default with 1.55volts for both thats how i discovered this way of overclocking. You can use ACC to Lower Volts when using High manual CPU and NBvolts aswell.

Theres just so much more of a challenge with Phenom overclocking when i compare to friends Core2Q's..

In the End they all ask why my Pc seems faster than thiers when they are @3.6 and im @3.5ghz..It seems kinda amazing to me how smooth the AMD platform really is @ any speed conpared to all my Friends Intels.

[cdnbum88]

Help me understand again the reason why you need or should keep your HT @2000?

I am at and cannot remember what auto cranks it up to, but I am stable at 3.3 and can get 3.5 with this approach.

Thanks for the insight in advance.

[gOtVoltage]

Help me understand again the reason why you need or should keep your HT @2000?

I am at and cannot remember what auto cranks it up to, but I am stable at 3.3 and can get 3.5 with this approach.

Thanks for the insight in advance.

HT On auto can be unstable in most cases and or it Can atomatically lower the HT for you if it works correct
Ive seen the Later(unstability when using AUTO HT on Most Mobo's when you pass a Certain point of OC.

Even @ stock i set the ht To 2000 even if my NB is @2600.
Although i have tested it to 2700mhz @ 3.5ghz

Each chip runs different and HT will vary but i use the same Method to set and or use the HT when overclocking on every Mobo ive tested.




Example ,,
why i set HT to 2000 regarless of NB speed ,,

Say if you set NB @2400 manually ,,the HT setting will show 2.4 = 2400 mhz automatically.Auto usually dosnt set it to 2000 all the time for HT at least.

@ HTT/fsb 200x13 9950stock ,,
the HT is 2.0 and NB is 2000mhz .Now if i raise the NB to 2400 the HT will automatically run 2400..If the Mobo or chip dosnt like it you will crash .

So @ 200x13 i will set NB @2400 and set the HT @2.0 = 2000mhz

The HT link that shows up when you change NB speed is the HT from CPU to NB . CPU to NB HT should be 2000mhz for stability.

Now if yo raise the FSB/HTT to 220x13 = 2800cpu ,,the HT usually will raise to 2200 if on auto or stock along with the NB.. In most cases the NB will be stable and HT at low CPU clocks(below 3.0ghz)..

Once the CPU goes above 3.0-3.2 this can or may become unstable and thus why i recomend to set the HT lower when you raise the FSB/htt ,Unless you have test the HT to go up to 2700mhz using low xCPU divider and raising FSB/HTT . The first thing i do is see what the Mobo can do on the FSB/HTT and how high HT can go before ever Raising my CPU overclock or NB @ stock volts.

Stock HT = 2000

210 HT = 2100

220 HT = 2200

230 HT = 2300

240 HT = 2400
and so on,,

Max ive ran HT is 270+ = 2700mhz HT.. 292 x 13.5 @ 2500ht. Its not easy by all means.

The NB acts the same exact way on My CPU..


If you are not giving the NB enuff volts you wont be able to run High NB and the system will not let you run High HT if NB is not stable.

Both go hand in hand , except that the NB can be higher than HT ..Thus i wont use auto HT becuse mostlikely it will not work as intended and crach the Pc.

So in this case i always set the HT to run @2000mhz regardless of my FSB/HTT and NB speed. The Higher the FSB/HTT the lower you must set the HT and NB depending on how fast your NB can run.

Example,,

210 x13 = 2700cpu and 2100HT/NB
usually HT can run 100mhz above stock when raising FSB/HTT

220 x13 = 2800cpu and 2200HT/NB
Sometimes you need to lower this HT back to 2000 which means using 1.8ht instead of 2.0HT.

So in Bios your setting will be

NB 2000 @220 x13 = 2200nb
HT 2000 @220 x13 = 2.0 = 2200HT( USE 1.8 instead of 2.0 to get 2000ht)

@240 x13 you will use 1.6 to get HT2000

You can run the NB well above the HT provided you give the NB the volts to do that.

Although ive seen many systems incuding mine run HT 2600 @ 3.5ghz it all depends on CPU and how high its clocked.

You need to play with HT.
Some systems like High HT and some dont. I usually see how much HT and NB i can run @ below 3.0ghz..I max them both out.. I then see if i can raise the CPU xmulti more If im using FSB/HTT(stock or even raised above stock). if it crashe with Higher CPUxMulti Lower the NB and or HT till it works..

Then i repeat the steps and eventually mu CPU is running higher clocks

Sorry for Long post,,
Not easy subject to absorb,,

gOtVolTage

[justapost]

Hmm, have you reached an point where too low HT speed was the cause of system instability?

The Asus board seems to allow an 10x max HT multi like the asrock or can you use higher multis if you use higher NB multis?

Could you run mem at 800 mode with an 270MHz ref HT and 10x NB multi or had you used 667 mode?

Thanks for the modding tipps saw you did a similar mod to the d-tec. I hope the D5 is more shortage prove and I like the fact that it's variable in speed. Was just a small leakage on the reservoir on top of the ultra, but the pumps bottom is not waterprove so electronic blew up.

[gOtVoltage]

^^^^JustaPost^^^^

Hmmm ill have to remember (looking for Screens).. I think i have one where i used like the stock 10xHT/NB multi to get 2600+HT with 800ram or 1066 @13xmulti i think.

Also if i run less than 1800HT System dosnt like it at all . My NB wont even run Below 1800mhz.. Since NB is designed for 1800minimun on Phenom.

I pretty much can use 400/533/667/800 for High HT..Depend which ram im using . Also i up the HT volts to 1.3v-1.32v for Super duper High HT

Ill see what i can find .. Havnt tried High HT since i Ran 292 with this Bios..I kinda just did some Quik tests with out saving Bunch of screenies..

Above 3.5ghz my system like the HT to be low due to My CPU and High Ram Freqency. I do Know Usually you can sqeeze more HT while running below 1100mhz ram and 3.5ghz .


Note:
while using 260FSB/HTT 260 x 13.5 = 2600mhz HT on this Mobo . I also used 800 Ram divider with 1066 ram. HT will be set to 10xDefault My NB can also do this @default 10x
The Higher the HTT is raised Past 260 on this Mobo with 602Bios the harder it is to keep High HT.@ 270-280 i would have to Lower HT to around 2400 or less. @ 292 i have to use 2000HT to keep Mobo Stable with 1.32v on the HT. Waiting for New Bios to get that Majic 300!HTT

Ive found that after 292 All my Dividers and CPUxmutis result in raising the CORE to above 3.6ghz .. Even if i use a low CPUxmulti it will say its @ 3600 if i try to set 293x12 = 3516,, the Mobo will report as 3600mhz. Same goes for if i Try 11x 10x 9x 8x it will not boot and say that My CPU is 3600mhz or Higher/ ive even seen 4800mhz in Bios!

This is Clearly a ASUS BIOS Problem with the Dividers for Ram and or CPU when going above 293htt.