DFI Lanparty UT P45-T2RS Banter starts here!!!

[prostoman]

I dont mean to tease you guys..... well ok I am but I went for the QX9650 and expecting to have all hardware in the house by 1st dec (there is always hope). I figured I might loose less money on buying the QX than a new E8500, just hope it performs.

[Jor3lBR]

I dont mean to tease you guys..... well ok I am but I went for the QX9650 and expecting to have all hardware in the house by 1st dec (there is always hope). I figured I might loose less money on buying the QX than a new E8500, just hope it performs.

Keep your hopes up . The board only gives up on Quads when running high FSB but with unlock multi you have better chances as you wont need to push high FSB:

Clocking DFI X48 with QX96505.8Ghz


With cascade but at least you can see what you can expect

[C-N]

I dont mean to tease you guys..... well ok I am but I went for the QX9650 and expecting to have all hardware in the house by 1st dec (there is always hope). I figured I might loose less money on buying the QX than a new E8500, just hope it performs.

Awesome, the spotlight's on you keep us posted.

[fellix_bg]

Here is some 45nm quad o.c.:



The BIOS setup:

>CPU Feature:
 
Thermal Management Control.......... - Enabled
PPM(EIST) Mode...................... - Disabled
Limit CPUID MaxVal.................. - Disabled
CIE Function........................ - Disabled
Execute Disable Bit................. - Disabled
Virtualization Technology........... - Disabled
Core Multi-Processing............... - Enabled
 
>DRAM Timing:
 
Enhance Data transmitting........... - Auto
Enhance Addressing.................. - Auto
T2 Dispatch......................... - Auto

>Clock Setting Fine Delay Press Enter:

DLL And RCOMP Settings.............. - Auto
Ch1 Dram Defaul Skew................ - Model 0
Ch2 Dram Defaul Skew................ - Model 0
RCOMP Settings...................... - Model 2

Fine Delay Step Degree.............. - 70ps
Ch1 Clock Crossing Setting.......... - Auto
DIMM1 Clock Fine Delay.............. - Current[1346ps]
DIMM2 Clock Fine Delay.............. - Current[1346ps]
Ch1 Control0 Fine Delay............. - Current[166ps]
Ch1 Control1 Fine Delay............. - Current[166ps]
Ch1 Control2 Fine Delay............. - Current[124ps]
Ch1 Control3 Fine Delay............. - Current[110ps]
Ch1 Command Fine Delay.............. - Current[262ps]

Ch2 Clock Crossing Setting.......... - Auto
DIMM3 Clock Fine Delay.............. - Current[1346s]
DIMM4 Clock Fine Delay.............. - Current[1346ps]
Ch2 Control0 Fine Delay............. - Current[14ps]
Ch2 Control1 Fine Delay............. - Current[56ps]
Ch2 Control2 Fine Delay............. - Current[0ps]
Ch2 Control3 Fine Delay............. - Current[0ps]
Ch2 Command Fine Delay.............. - Current[110ps]

Ch1 Ch2 Common Clock Setting........ - Auto

Ch1 RDCAS GNT-Chip Delay............ - Auto
Ch1 WRCAS GNT-Chip Delay............ - Auto
Ch1 Command To CS Delay............. - Auto
.
Ch2 RDCAS GNT-Chip Delay............ - Auto
Ch2 WRCAS GNT-Chip Delay............ - Auto
Ch2 Command To CS Delay............. - Auto

Flex Memory Mode..................... - Auto
CAS Latency Time (tCL)............... - Auto
RAS# to CAS# Delay (tRCD)............ - Auto
RAS# Precharge (tRP)................. - 5 (Auto sets this at 7)
Precharge Delay (tRAS)............... - Auto
All Precharge to Act................. - Auto
REF to ACT Delay (tRFC).............. - Auto
Performance Level.................... - Auto

>Read delay phase adjust Press Enter:

Channel 1 Phase 0 Pull-In........... - Auto
Channel 1 Phase 1 Pull-In........... - Auto
Channel 1 Phase 2 Pull-In........... - Auto
Channel 1 Phase 3 Pull-In........... - Auto
Channel 1 Phase 4 Pull-In........... - Auto

Channel 2 Phase 0 Pull-In........... - Auto
Channel 2 Phase 1 Pull-In........... - Auto
Channel 2 Phase 2 Pull-In........... - Auto
Channel 2 Phase 3 Pull-In........... - Auto
Channel 2 Phase 4 Pull-In........... - Auto

Write to PRE Delay (tWR)............ - Auto
Rank Write to Read (tWTR)........... - Auto
ACT to ACT Delay (tRRD)............. -Auto
Read to Write Delay (tRDWR)......... - Auto
Ranks Write to Write (tWRWR)........ - Auto
Ranks Read to Read (tRDRD).......... - Auto
Ranks Write to Read (tWRRD)......... - Auto
ALL PRE to Refresh.................. - Auto

>Voltage Settings:

CPU VID Control..................... - 1.40V
CPU VID Special Add................. - Enabled
CPU VID Special Add................. - Auto
DRAM Voltage Control................ - 2.01v
SB Core/CPU PLL Voltage............. - 1.55v
NB Core Voltage..................... - 1.351v
CPU VTT Voltage..................... - 1.29v
Vcore Droop Control................. - Disabled
Clockgen Voltage Control............ - 3.45v
GTL+ Buffer Strength................ - Strong
CPU GTL 0 REF Volt.................. - 0.6300
CPU GTL 2 REF Volt.................. - 0.6300
CPU GTL 1 REF Volt.................. - 0.6300
CPU GTL 3 REF Volt.................. - 0.6300
North Bridge GTL 0 REF Volt......... - 0.6750
North Bridge GTL 1 REF Volt......... - 0.6750
FSB Vref............................ - Auto
 
Genie BIOS Settings:
 
Exist Setup Shutdown................ - Mode 2
Exist Shutdown After AC loss........ - Enabled
AC Shutdown Free.................... - Enabled
O.C Clock Fail Retry Counter........ - 1
O.C Clock Fail CMOS Reloaded........ - Disabled
CPU Clock Ratio..................... - 8
Target CPU Clock.................... - 3800 MHz
CPU Clock........................... - 475
Boot Up Clock....................... - Auto
CPU Clock Amplitude................. - 800mV
CPU Clock0 Skew..................... - 0ps
CPU Clock1 Skew..................... - 0ps
DRAM Speed.......................... - Auto (A manual set at the same ratio crashes)
Target DRAM Speed................... - 1141MHz
PCIE Clock.......................... - 100mhz
PCIE Slot Config.................... - 1x 1x 
CPU Spread Spectrum................. - Disabled
PCIE Spread Spectrum................ - Disabled

A thoughtful testing is still undergo, but for now (an hour of rendering) the system is stable.

[C-N]

He he, I got almost the exact same clock priming right now with a Q9650 & 4 x 1GB Sticks.

Worker threads are all over the place but its still running I'll post up my settings if it runs a loop properly.

CPU Voltage is crazy, I think I've got about 1.45625 set in bios which drops to 1.4 something in windows which then droops to 1.36 under Linpack load with vdroop control disabled!!! DFI have got to sort this out!!!

NB, CPU & VTT are all a good few clicks over what they need to be btw.

[Kris]

Keep the bios templates coming. I am still trying to sort this board out. Those templates are helpful!