Micron D9 GMH\GKX\JKH etc club

[philbrown23]

holy man! those are kick ass scores!

[PolRoger]

i doubt its d9gkx
all of my d9gkx need 2.3v+ for 1200
and 2 of em wont even boot below 2.1-2.2v

They are spec. at 2.3v (PVS22G9600ELK)... the Ram List at i4memory doesn't list the Viper PC2-9600 just the PC2-9200.

I was also able to run my Kingston HyperX PC2-9200 (spec. 2.35v KHX9200D2K2/2GR) on my Gigabyte UD3P at 500fsb 5/6 divider DDR2-1200 with around 2.1v.

[zsamz_]

Are you sure they haven't degraded? My Team 1200 D9GKX only need 2.12v for 600MHz on my DFI P35.

i got so many sticks that i've only used them maybe 1 week total
and i was runnin then 3-3-3-8 @ 830mhz
i like d9ghm more

[neo mike]

sure brag alot about how many memory sticks you have

[fatguy1992]

I got my Dominator PC2-8500's back from RMA and they are version 5.1.

I had a look and they weren't listed.

Good? Bad?

I'll do some overclocking tomorrow

[zsamz_]

sure brag alot about how many memory sticks you have

well i like d9 i cant seem to wanna sell any of my ram
i tryin but i just cant give em up
and i keep buyin more
i got 30+ gigs of ddr2 n i want more

I got my Dominator PC2-8500's back from RMA and they are version 5.1.

I had a look and they weren't listed.

Good? Bad?

I'll do some overclocking tomorrow

got a set of dominator 8500 1.2 last week and they were pure crap couldnt go over 1200 stable even with 2.4v i will be bringin em back to the shop soon
i wanted to add them to my d9 collection but 80$ for a crap set no ty

[neo mike]

well i have some xtreem teams 10400 1300s for sale if you want to add to your collection ?

[fatguy1992]

got a set of dominator 8500 1.2 last week and they were pure crap couldnt go over 1200 stable even with 2.4v i will be bringin em back to the shop soon
i wanted to add them to my d9 collection but 80$ for a crap set no ty

My old ones (that died) were version 1.2 and they got me 1200MHz @ 4-4-4-1 W/ 2.5v and easy did over 1200MHz @ 5-5-5-15 with less then 2.4v.

[fatguy1992]

Anyway is version 5.1v good?

[zsamz_]

My old ones (that died) were version 1.2 and they got me 1200MHz @ 4-4-4-1 W/ 2.5v and easy did over 1200MHz @ 5-5-5-15 with less then 2.4v.

i got a dud couldnt do 1200 cas 5
n those 5.1 you might get lucky they might do 1200 but carefull with volts on those

[Ket]

My D9 GKX do 1206MHz @ 2.1v in BIOS, boot even @ 2.0v and everything seems stable. Will mess around with them more when I can but I'll have to start messing with skews.

[PolRoger]

I decided to try out my Kingston HyperX PC2-9200 D9 GKX to see if I could also run them at DDR2-1200 with low volts... I left all the voltages at stock settings and ran 7x500 with 5/6 divider. The DDR voltage on the UT was 1.91v!

[CryptiK]

Very nice voltage for that speed, one of the lowest I have ever seen. Very good ram indeed.

[WaterFlex]

PolRoger
Nice ram, mate

[PolRoger]

I swapped in my set of Patriot Viper and they appear to run at the same settings as well.

I think the motherboard and the 333 latch 5/6 divider is a big factor. My UD3P also seems to have a compatible 333 5/6 divider with my D9 GKX sticks.

I will note however that I haven't had much luck running the Viper or the HyperX at high speeds (with any divider) on my Biostar boards.

[OC4/3]

Anyone here have SPD dump of Team Xtreem DDR 2 1066 CL5?I would need it for just in case scenario.

[PolRoger]

PolRoger
Nice ram, mate

I was checking out your sig and it got me thinking... and I thought why not... so I installed the HyperX in dimm 1+3 and the Viper in dimm 2+4 changed the multi to 8 and set cpu vcore to 1.25v shows 1.21v in bios. All the other voltages were left at stock. I was running prime blend when I took the screenshot. CPU vcore was mostly at 1.20v while running under load sometimes dipping to 1.184/1.9v.

[WaterFlex]

Wow! Unbelievable! It seems DFI rocks. 500 FSB at 1,12 vNb and 1,91 vDimm.

[Shiranui Gen-An]

Well, Smart Guardian tends to report VDIMM as being lower than the actual voltage, at least with the LT/UT P35 boards.

[westsider]

the best micron D9 ever had are Cellshock 8500 black for me

i could achieve
700Mhz
http://valid.x86-secret.com/show_oc.php?id=415732
486.9MHz 3-2-2-1
http://valid.x86-secret.com/show_oc.php?id=415746

superpi32M stabil 500MHz 3-4-3-9
628Mhz 4-4-4-12
http://valid.x86-secret.com/show_oc.php?id=415755

[WaterFlex]

westsider
Very good results. Did you have "Red Devils" ? I think they are a little better than your 8500.

[westsider]

i have tried red devils and they get better timings

but for Max Takt blacks are better

GKX timing vs GMH clock

[CryptiK]

PolRoger - It would make a lot more sense if the DFI voltage software is under-reporting the voltages, I have a hard time believing the ram or the NB for that matter would be stable at those speeds & PL. Any chance you can measure the real vdimm with a DMM please?

westsider - nice work, what voltages were used for each setting. Also your link for 32M CL3 is missing.

[westsider]

i am sorry for my mistake

it was a long time ago


it was 1M test

[WaterFlex]

i have tried red devils and they get better timings

but for Max Takt blacks are better

GKX timing vs GMH clock

Agree with you.