ASUS P5Q-E (P45) pre-view

[gugle]

Think the latest release by intel for the TJcasemax specs was 95°C for Q6600 and not 100°C as we always presumed... so for me realtemp... which cooler mate ?

then the RealTemp is the most right?
I use a set that WC

----------
I can not stable ..
will be memory or cpu?


Test In-Place FFTs


ASUS P5Q-E Rev A2 Motherboard
Q6600 G0 (Vid-1325v)
4x1GB AxeRam (micron) PC2-6400 4-4-4-12 (1.8v)
8800GT
Vista64 SP1

AI Tweaker

AI Overclock tuner: MANUAL
CPU Ratio Setting: 8
FSB Frequency: 425
PCI-E Frequency: 100
FSB Strap to North Bridge: Auto
DRAM Frequency: DDR2-1066
DRAM CLK Skew on Channel A1: Auto
DRAM CLK Skew on Channel A2: Auto
DRAM CLK Skew on Channel B1: Auto
DRAM CLK Skew on Channel B2: Auto
DRAM Timing Control: MANUAL

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : Auto
Row Refresh Cycle Time: 50
Write Recovery Time: Auto
Read to Precharge Time: Auto

2nd Information :

READ to WRITE Delay (S/D): Auto
Write to Read Delay (S): Auto
WRITE to READ Delay (D): Auto
READ to READ Delay (S): Auto
READ to READ Delay (D): Auto
WRITE to WRITE Delay (S): Auto
WRITE to WRITE Delay (D): Auto

3rd Information :

WRITE to PRE Delay: Auto
READ to PRE Delay: Auto
PRE to PRE Delay: Auto
ALL PRE to ACT Delay: Auto
ALL PRE to REF Delay: Auto
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Auto
AI Clock Twister: Auto
AI Transaction Booster: Auto


CPU Voltage: 1.4250
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): Auto
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.32
DRAM Voltage: 2.16
NB Voltage: 1.34
NB GTL Reference: Auto
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
CPU Margin Enhancement: Optimized

[thehinge1]

My revision 1.01g P5Q-E with 'A2' revision chipset sucked big-time!

However, I have a pair of A3's now and they are both working perfectly

My 'rig time' has been a bit limited lately, but thus far have the E7200@3.8GHz/475fsb/ddr2-1140 on 5:6 with CPU PLL at 1.52, 1.22VTT, and NB at 1.22v as well. I can probably run the NB at or below 1.20v with more GTL tweaking (at 0.580 now for NB ref). Currently running 5-5-5-18 at PL-8.

The E8400 is at 4.005GHz/445fsb/ddr2-1068 at 5-5-5-15 PL-9 (I think, might be 8). CPU PLL 1.52, 1.16VTT, NBv 1.18 as I'm still playing with FSB/RAM.

Seems to be XP64 likes more NBv/slightly lower NB GTL ref than XP32 on the dual-boot E7200 rig. That's all for now

[supermario]

thehinge1,

would you let me know the revision of your A3 boards?
All boards in my area are rev. 1.01G.

[thehinge1]

Both boards are ASUS revision '1.01g' just like the 'less-than-consistent' (and despised) first board. The shipping bios on both boards is 1201 dated 08/05/2008 as they POST so they were at least made after that date, so they quite possibly were made in August supported the year/month theory.

cchilb - you get your board from the egg? Looks like we are 2 digits apart.

Note: 9mm 124gr.+P GDHP in photo is in case I ever see my first P5Q-E again, that sucker is toast!

thehinge1,

would you let me know the revision of your A3 boards?
All boards in my area are rev. 1.01G.

[cchilb]

Ordered on 10-22-08 from the Egg, it shipped from Memphis.