"ASUS P5Q Deluxe discussion".

[RBS]

hmm I flash back to 1306 ? max whit 1406 an E8600 is 450x10 an 1306 It is 510x10 an to 24/7 480x10

but to 420x10 is 1402 nice,but not to high overclock.

Maybe less overvolt with new 1402, that´s why ur lower oc.

[Martin.v.r]

I try all volt set/memset whit 1406 no go can not run a 3D-mark test over 450x10

hmm i can try a lower multip.. but that is not fun

i test whit slot 1/3 an 2/4 Cellshock PC8000 CL4 an G.skill PC8000 CL4-4-4-5

auto temingset whit bios 1306 is 5-5-5-18 an whit bios 1406,It is 5-5-5-15

[Wolf132]

Im still using 0806, have not had 1 crash that wasnt a failed overclock. Runs a lot better than my old nforce board.

[Leeghoofd]

Lee can you repost your template for the QX9650. I want to see if mine will do the same.

AI Overclock tuner: Manual
CPU Ratio Setting: 10
FSB Frequency: 400
FSB Strap to North Bridge: AUTO
PCI-E Frequency: 101
DRAM Frequency: 1066
DRAM Timing Control: Manual

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

DRAM Static Read Control: Enabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: Manual
( Level 7)
PULL-INS: All Disabled 

CPU Voltage: 1.250 
CPU GTL Voltage Reference: AUTO
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.24
DRAM Voltage: 1.94
NB Voltage: 1.26
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew: AUTO
NB Clock Skew: AUTO
CPU Margin: Optimized

Advance CPU Settings
CPU Ratio Setting: 10
C1E Support: Enable
Max CPUID Value Limit: Disabled
Intel Virtualization Tech: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled 

[Pntgrd]

Thanks

[s1Lv3r]

533x7.5 with fsb 1.26 nb 1.26 vcore 1.29 cpu pll 1.54 ok but try 8 multi with 1.35 vcore settings gets error on orthos try higher vcore settings but gets same error what can i do for get stable higher clocks

[RBS]

533x7.5 with fsb 1.26 nb 1.26 vcore 1.29 cpu pll 1.54 ok but try 8 multi with 1.35 vcore settings gets error on orthos try higher vcore settings but gets same error what can i do for get stable higher clocks

Try PLL 1.56

[s1Lv3r]

Try PLL 1.56

i try pll with 1.56 dont change anything orthos run smallFFT's fine 533x7.5 but blend tests get an error in 15 seconds

[davidoff619]

right this is one thing that buging the s**t out of me bio 504 or somthing like that had no problems posting within 5 second but ive tried every bios since but takes 30 seconds plus to post ive got the 9800 gx2 amd the blue light doesnt come on but all fans and stuff startthen the light and grapics/picture/post procces kicks in. not that bad but wait theres more even at stock voltagers everything on auto 80%of time will not boot will atke quite a few times restarting and full power of then 45% of the time just keep resetting for like 10-15 mins somtime with no luck/ please help me find out the anser please as it cant be hardware related because it boots first time everytime in 503 but have a q9650 so need to run over 1003

thanks in advance

[JohnLoph]

Holy!! Others reported anywhere from 0.01 to 0.06 vDIMM overvolt on 1306. This is the most I've seen... I think I gotta set mine back a bit

my P5Q DLX with v1306

PLL : 1.54 (bios) ---> 1.59 (real) // +0.05

vFSB : 1.28 (bios) ---> 1.30 (real) // +0.02

vDimm : 2.04 (bios) ---> 2.15 (real) // +0.11

vNB : 1.28 (bios) ---> 1.33 (real) // +0.05

that too insane overvolt >_<"



using 2 multi-meters got same result

> GW INSTEK GDM-350A



> YUGO DT838

[waynetu]

mine with 1306m bios

vDimm : 1.92 (bios) ---> 2.00 (real) +0.08

vNB : 1.22 (bios) ---> 1.265 (real) +0.045

measured by automatic multimeter

[CryptiK]

lol I told you something was up with these boards and voltages. Asus should get a slap on the wrist.

Mine (at the moment, they change every time I flash the bios):

Vdimm:
2.00 = 2.06
2.02 = 2.08
2.04 = 2.10
2.06 = 2.12
2.08 = 2.14
2.10 = 2.16

vFSB:
1.12 = 1.11
1.14 = 1.13

vNB:
1.22 = 1.23
1.24 = 1.25
1.26 = 1.27
1.28 = 1.29

I wish my Maximus II Formula came today. Oh well, I'll get it tomorrow.

[Martin.v.r]

1406 I test the bios an it can not read multip.. 9,5/10 over 450 fsb,but x9 is It ok an here can it read mem over 1200MHZ

i got a vcore drop in all bios = 0.1250v bot not in bios 1306 there it is 0.1000v all set

from 500 fsb to 511 fsb there is a drop,ASUS P5K got It to.

[CryptiK]

1406 I test the bios an it can not read multip.. 9,5/10 over 450 fsb,but x9 is It ok an here can it read mem over 1200MHZ

i got a vcore drop in all bios = 0.1250v bot not in bios 1306 there it is 0.1000v all set

from 500 fsb to 511 fsb there is a drop,ASUS P5K got It to.

Do you mean that you couldn't get the ram over 1200 MHz using any of the other bioses?

[BeastNotro]

Martin.v.r

Did you test 1402 or 1402m (kets bios)

By the way you keep posting it as 1406 in your posts when it is 1402 and everytime you get me as i am like where is this 1406 he keeps posting about...

Important:

Also are you always using Official Bioes or Kets Modded ones ????

[davidoff619]

cann anyone tell help how to open new topic please thanks David

[RBS]

Thanks for the tensions guys. I got reads from one mate for 1306 @ 400x8 and after seeing ur reads it seems that each mobo overvolts different, maybe due to "made in Taiwan" or "made in china" ? I think Taiwan are better one.
I´ve seen there isn´t overvolt at minimun tension like auto with 1306.

[Martin.v.r]

sorry yes It is bios 1402
more test,so successful it whit bios 1402 an multip 480x10 buut It ned Xtrem vcore 1.488v bios set 1.500v, whit bios 0806 it is 1.4500v
hmm

[Leeghoofd]

sorry yes It is bios 1402
more test,so successful it whit bios 1402 an multip 480x10 buut It ned Xtrem vcore 1.488v bios set 1.500v, whit bios 0806 it is 1.4500v
hmm

Well board is weird with the Quad I get spot on values ( LLC enabled ) with what I set in the bios (under load that is), with the E8400 I get about 0.05 lower than what is set in the bios... popped the quad back in and spot on...

[JohnLoph]

Thanks for the tensions guys. I got reads from one mate for 1306 @ 400x8 and after seeing ur reads it seems that each mobo overvolts different, maybe due to "made in Taiwan" or "made in china" ? I think Taiwan are better one.
I´ve seen there isn´t overvolt at minimun tension like auto with 1306.

I agree that if compare between China and Taiwan, Taiwan is better!!

Singapore, Malaysia, Taiwan, China

[Martin.v.r]

made in Taiwan here ?

[CryptiK]

You're made in Denmark, Martin jk

I think mine is made in China.

[RBS]

You're made in Denmark, Martin jk

I think mine is made in China.

Mine is Chinese too, I think these need at least more vNB than others for high FSB; about the other tensions I´m not sure.

[golfjam]

I agree that if compare between China and Taiwan, Taiwan is better!!

Singapore, Malaysia, Taiwan, China

I agree. I loved Asus because all mobos were made in Taiwan but they moved some of the production to China, unfortunately. It may look the same but the quality is definitely different.

[truehighroller]

Mine is Chinese too, I think these need at least more vNB than others for high FSB; about the other tensions I´m not sure.

If that is true then mine must be Taiwan because I only need 1.28vnb for my quad @ 3.85~