Also try increasing vcore to 1.40 - 1.42v (bios) it may just be your cpu. You should be safe up to at least 1.45v vcore with the 65nm if you can keep the heat under control.
Also try increasing vcore to 1.40 - 1.42v (bios) it may just be your cpu. You should be safe up to at least 1.45v vcore with the 65nm if you can keep the heat under control.
Ci7 990X::Rampage III Extreme::12GB Corsair Dominator 1866C7GT::2 x EVGA SC Titans in SLI::Corsair AX1200::TJ07::Watercooled
Ci7 920 3849B018::Rampage II Extreme::6GB GSKILL Trident 2000C9 BBSE::EVGA GTX580::Antec Signature SG850::TJ09::Aircooled w/TRUE 120X
Yes, i know these limits for 65nms .
But the weather is too hot here , my room is appr. 30C now.
My cores are max: 67 67 61 62 with realtemp with 1.38125V for now . ( at that moment it makes 8k test with blend )
I know that these temps won't be so high anytime except torturing.
There is another question btw , what are the safe temps for torturing,bench in realtemp ?
Btw , stable for about 25 mins. ( with GTL REFs 0/2 , 1/3 = 0.690 )
Q6600 G0 @ 3.4GHz @1.39375(VID:1.3125) + OCZ VENDETTA 2 + OCZ FREEZE // ASUS P5Q DELUXE (0803 BIOS) // 2x1 GB PC2 9600 1200MHz 5-5-5-18 @ 1278MHz 5-5-5-15 OCZ REAPER // POWERCOLOR HD4870 // 2x250GB SEAGATE ST3250410AS@RAID 0 // LOGITECH Z-2300 2+1 // SAMSUNG SH-S223F 22X SATA DVD RW // COOLER MASTER CENTURION 534 PLUS // SAMSUNG 770P LCD // OCZ STEALTHXSTREAM 600W
Fair enough about the temps, that's why I mentioned it, not knowing where you live or your climate.Originally Posted by Tulū
Hope the GTL REF gets you that FSB stable. Many people even run 0.70x (0/2, 1/3) on the 6600's. Also try reducing the FSB term voltage to around 1.42v an using 0.70x - 0.72x GTL REF. Lowering the vFSB will reduce your temps slightly.
Ci7 990X::Rampage III Extreme::12GB Corsair Dominator 1866C7GT::2 x EVGA SC Titans in SLI::Corsair AX1200::TJ07::Watercooled
Ci7 920 3849B018::Rampage II Extreme::6GB GSKILL Trident 2000C9 BBSE::EVGA GTX580::Antec Signature SG850::TJ09::Aircooled w/TRUE 120X
I follow you .
Did not increase vcore again , hold it at 1.38125.
Lowered FSB term. to 1.42
GTL REF 0/2 = 0.710
GTL REF 1/3 = 0.720
Here are my all settings :
Btw , i live in Turkey .Code:AI Overclock tuner: manual CPU Ratio Setting: 8 FSB Strap to North Bridge: AUTO FSB Frequency: 425 PCI-E Frequency: 100 DRAM Frequency: 851 DRAM CLK Skew on Channel A1: AUTO DRAM CLK Skew on Channel A2: AUTO DRAM CLK Skew on Channel B1: AUTO DRAM CLK Skew on Channel B2: AUTO DRAM Timing Control: manual 1st Information : CAS# Latency: 5 DRAM RAS# to CAS# Delay: 5 DRAM RAS# Precharge: 5 DRAM RAS# Activate to Precharge: 15 RAS# to RAS# Delay : AUTO Row Refresh Cycle Time: 40 Write Recovery Time: AUTO Read to Precharge Time: AUTO 2nd Information : READ to WRITE Delay (S/D): AUTO Write to Read Delay (S): AUTO WRITE to READ Delay (D): AUTO READ to READ Delay (S): AUTO READ to READ Delay (D): AUTO WRITE to WRITE Delay (S): AUTO WRITE to WRITE Delay (D): AUTO 3rd Information : WRITE to PRE Delay: AUTO READ to PRE Delay: AUTO PRE to PRE Delay: AUTO ALL PRE to ACT Delay: AUTO ALL PRE to REF Delay: AUTO DRAM Static Read Control: Disabled DRAM Read Training: enabled MEM. OC Charger: enabled AI Clock Twister: lighter AI Transaction Booster: AUTO CPU Voltage: 1,38125 CPU GTL Voltage Reference (0/2): 0.710 CPU GTL Voltage Reference (1/3): 0.720 CPU PLL Voltage: 1.52 FSB Termination Voltage: 1.42 DRAM Voltage: 2.10 NB Voltage: 1.34 NB GTL Reference: AUTO SBridge Voltage: AUTO PCIE SATA Voltage: AUTO Load Line Calibration: enabled CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled CPU Clock Skew : auto NB Clock Skew : auto Advance CPU Settings CPU Ratio Setting: Manual CPU VID: Default C1E Suppport: Disabled Max CPUID Value Limit: Disabled Intel® Virtualization Tech: Disabled Vanderpool Technology: Disabled CPU TM Function: enabled Execute Disable Bit: Disabled
Harry Kewell plays for us .
Edit :Ooopss , system restarted.
It seems Fsb term 1.42 was low , what do you think ?
I increased to 1.46 again.
Edit2: Restarted again with 1.46 FSB TERm.
Seems GTL REFs high ?
Lowered to 0.700 both.
Last edited by Tulū; 08-20-2008 at 06:55 AM.
Q6600 G0 @ 3.4GHz @1.39375(VID:1.3125) + OCZ VENDETTA 2 + OCZ FREEZE // ASUS P5Q DELUXE (0803 BIOS) // 2x1 GB PC2 9600 1200MHz 5-5-5-18 @ 1278MHz 5-5-5-15 OCZ REAPER // POWERCOLOR HD4870 // 2x250GB SEAGATE ST3250410AS@RAID 0 // LOGITECH Z-2300 2+1 // SAMSUNG SH-S223F 22X SATA DVD RW // COOLER MASTER CENTURION 534 PLUS // SAMSUNG 770P LCD // OCZ STEALTHXSTREAM 600W
Failed on core0 after one hour.
Will increase vcore a notch.
Q6600 G0 @ 3.4GHz @1.39375(VID:1.3125) + OCZ VENDETTA 2 + OCZ FREEZE // ASUS P5Q DELUXE (0803 BIOS) // 2x1 GB PC2 9600 1200MHz 5-5-5-18 @ 1278MHz 5-5-5-15 OCZ REAPER // POWERCOLOR HD4870 // 2x250GB SEAGATE ST3250410AS@RAID 0 // LOGITECH Z-2300 2+1 // SAMSUNG SH-S223F 22X SATA DVD RW // COOLER MASTER CENTURION 534 PLUS // SAMSUNG 770P LCD // OCZ STEALTHXSTREAM 600W
Reply With Quote
Bookmarks