Here is my Q6600 @ 3.6ghz Air Cooled finally as of yesterday evening and this morning Orthos Primed 11hrs 5min 4 secs before i stopped it and with these settings in bios, in my template below.
Bios 1103 and 1201:
**** System Performance Settings ****
*******************************
AI Overclock tuner: Manual
CPU Ratio Setting: 8.0
FSB Frequency: 450
PCI-E Frequency: 101
FSB Strap to North Bridge: Auto
DRAM Frequency: DDR2-901 MHz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information: 5-5-5-15-3-52-6-3
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information : 8-3-5-4-6-4-6
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information : 14-5-1-6-6
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Auto
MEM. OC Charger: Auto
AI Clock Twister: Auto
AI Transaction Booster: Auto
All Pull-In's: Disabled
CPU Voltage: 1.425 ( 1.416v idle | 1.43 full )
CPU GTL Voltage Reference (0/2): 0.630
CPU GTL Voltage Reference (1/3): 0.670
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.28
NB Voltage: 1.26
DRAM Voltage: 1.96
NB GTL Reference: 0.630
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew: Auto
NB Clock Skew: Auto
CPU Margin Enhancement: Optimized
**** Advance CPU Settings ****
**************************
CPU Ratio Setting : 8x
C1E Support: Disabled
Max CPUID Value Limit: Disabled
Intel Virtualization Tech: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
Here is screen shot just before stopping Orthos which i just took this morning at 6:44am.
Also not sure why, but Orthos states it is at 4050mhz.. lol
I stopped Orthos .. as i say she is good enough. I usually do 8-10 hours of orthos (when ever i OC) and i have never had any issues afterwards, but one never knows as you can prime for 24hrs and still have issues later on, but 8-10hrs is ideal for daily usage and or 24/7 usage.
Temps were decent, but i must inspect The Thermal Paste and heatsink mounting .. as it appears at times ... 2 cores are 8-10C higher then the other 2 ... cores 0-1 is 8-10C higher when OCing then cores 2-3, but at idle they are only 1-2C difference.
Idle right now is 33-32-28-30
Well i figured i run this program now to see if i am actually 100% stable as i just ran Orthos for 11 hrs last night/this morning... post is above and it never errored out, but if you read in this theard ppl who primed 10 hours or so .. ran linkpack and was not stable.
IntelBurnTest
http://www.xtremesystems.org/forums/...d.php?t=197835
Ok this program gets Cores HOTTER then Orthos Prime.
I need to figure out why 2 of my cores always read 10C higher then the other 2.
Linpack 0-1 Cores 84C and 2-3 Cores 74C Max.
Orthos = 0-1 Cores 74C and 2-3 Cores 64C Max. (Were talking like 2-3 instances of 3 secs of a Max of 74C)
Here is my test results just done 15 min ago and all is OK Residual result numbers 5 passes all same.
Also ppl read the read me text ... only use what free memory is available to use.
Reply With Quote
Bookmarks