"ASUS P5Q Deluxe discussion".

[BeastNotro]

By the way here is my Q6600 @ 3.6ghz Air Cooled finally as of yesterday evening and this morning Orthos Primed 11hrs 5min 4 secs before i stopped it and with these settings in bios, in my template below.


Bios 1103 and 1201:

**** System Performance Settings ****
*******************************
AI Overclock tuner: Manual
CPU Ratio Setting: 8.0
FSB Frequency: 450
PCI-E Frequency: 101
FSB Strap to North Bridge: Auto
DRAM Frequency: DDR2-901 MHz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information: 5-5-5-15-3-52-6-3
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information : 8-3-5-4-6-4-6
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information : 14-5-1-6-6
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO

DRAM Static Read Control: Disabled
DRAM Read Training: Auto
MEM. OC Charger: Auto
AI Clock Twister: Auto
AI Transaction Booster: Auto

All Pull-In's: Disabled

CPU Voltage: 1.425 ( 1.416v idle | 1.43 full )
CPU GTL Voltage Reference (0/2): 0.630
CPU GTL Voltage Reference (1/3): 0.670
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.28
NB Voltage: 1.26
DRAM Voltage: 1.96
NB GTL Reference: 0.630
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew: Auto
NB Clock Skew: Auto
CPU Margin Enhancement: Optimized

**** Advance CPU Settings ****
**************************
CPU Ratio Setting : 8x
C1E Support: Disabled
Max CPUID Value Limit: Disabled
Intel Virtualization Tech: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled

Here is screen shot just before stopping Orthos which i just took this morning at 6:44am.

Also not sure why, but Orthos states it is at 4050mhz.. lol




I stopped Orthos .. as i say she is good enough. I usually do 8-10 hours of orthos (when ever i OC) and i have never had any issues afterwards, but one never knows as you can prime for 24hrs and still have issues later on, but 8-10hrs is ideal for daily usage and or 24/7 usage.

Temps were decent, but i must inspect The Thermal Paste and heatsink mounting .. as it appears at times ... 2 cores are 8-10C higher then the other 2 ... cores 0-1 is 8-10C higher when OCing then cores 2-3, but at idle they are only 1-2C difference.

Idle right now is 33-32-28-30