well yeah for nb voltage im down to 1.36 which is not to bad imo.. i am going to play with the gtl's after i get the voltages as low as i can for now. then once i get them setup maybe ill be able to lower them even more
well yeah for nb voltage im down to 1.36 which is not to bad imo.. i am going to play with the gtl's after i get the voltages as low as i can for now. then once i get them setup maybe ill be able to lower them even more
upgrading...cooler master cm690 case, corsair hx850, samsung 1tb x 3, optiarc burners x2, gskill 4gb ripjaws, working on the rest again
sounds like data corruptionOriginally Posted by Fantom007
Yes when updating/changing BIOS version this sometimes occurs, Ive had alot of problems like this, i always use and old hdd with a clean install to test with when updating bios's so many times ive had to reinstall ..
[QUOTE=zfactor;3170966]here is the 714 one for you get it from this page: http://www.dfi.com.tw/Support/Downlo...FLAG=B&SITE=US]
Thank`s m8
ASUS RANGER VII
i7 4790K
8GB CORSAIR 1600 xmp
BE QUIET SHADOWROCK SR1
EVGA GTX 770
2 X 840 EVO SSD
CORSAIR AX850W
Here are my settings
Code:CPU Feature Page Thermal Management Control................Disabled PPM (EIST) Mode...........................Disabled Limit CPUID MaxVal........................Disabled CIE Function..............................Disabled Execute Disable Bit.......................Disabled Virtualization Technology.................Disabled Core Multi-Processing.....................Enabled Main BIOS Page Exist Setup Shutdown......................Mode 2 Shutdown After AC Loss....................Disabled O. C. Fail Retry Counter..................0 CLOCK VC0 Divider.........................Auto CPU Clock Ratio...........................9.5x CPU N/2 Ratio.............................Enabled CPU Clock.................................453 MHz Boot Up Clock.............................Auto DRAM Speed................................333/667 PCIE Clock................................100MHz PCIE Slot Config..........................1X 1X CPU Spread Spectrum.......................Disabled PCIE Spread Spectrum......................Disabled SATA Spread Spectrum......................Disabled Voltage Setting Page CPU VID Control...........................Auto 1.1825V CPU VID Special Add.......................109.21% DRAM Voltage Control......................2.190V SB Core/CPU PLL Voltage...................1.510V NB Core Voltage...........................1.304V CPU VTT Voltage...........................1.210V VCore Droop Control.......................Disabled Clockgen Voltage Control..................3.45V GTL+ Buffers Strength.....................Strong Host Slew Rate............................Weak GTL REF Voltage Control...................Enabled CPU GTL 1/52 REF Volt.....................72 CPU GTL 0/3 REF Volt......................70 North Bridge GTL REF Volt ................53 DRAM Timing Page Enhance Data Transmitting.................Fast Enhance Addressing........................Fast T2 Dispatch...............................Disabled Clock Setting Fine Delay..................Listed Below CAS Latency Time (tCL)....................4 RAS# to CAS# Delay (tRCD).................4 RAS# Precharge (tRP)......................4 Precharge Delay (tRAS)....................4 All Precharge to Act......................Auto REF to ACT Delay (tRFC)...................Auto Performance Level.........................Auto Read Delay Phase Adjust...................Listed Below MCH ODT Latency...........................Auto Write to PRE Delay (tWR)..................Auto Rank Write to Read (tWTR).................Auto ACT to ACT Delay (tRRD)...................Auto Read to Write Delay (tRDWR)...............Auto Ranks Write to Write (tWRWR)..............Auto Ranks Read to Read (tRDRD)................Auto Ranks Write to Read (tWRRD)...............Auto Read CAS# Precharge (tRTP)................Auto ALL PRE to Refresh........................Auto Read Delay Phase Adjust Page Channel 1 Phase 0 Pull-In.................Auto Channel 1 Phase 1 Pull-In.................Auto Channel 1 Phase 2 Pull-In.................Auto Channel 1 Phase 3 Pull-In.................Auto Channel 1 Phase 4 Pull-In.................Auto Channel 2 Phase 0 Pull-In.................Auto Channel 2 Phase 1 Pull-In.................Auto Channel 2 Phase 2 Pull-In.................Auto Channel 2 Phase 3 Pull-In.................Auto Channel 2 Phase 4 Pull-In.................Auto Clock Setting Fine Delay Page Ch1 Clock Crossing Setting................More Aggresive DIMM 1 Clock fine delay...................Current 1924ps DIMM 2 Clock fine delay...................Current 1074ps DIMM 1 Control fine delay.................Current 1012ps DIMM 2 Control fine delay.................Current 1012ps Ch 1 Command fine delay...................Current 1474ps Ch2 Clock Crossing Setting................More Aggresive DIMM 3 Clock fine delay...................Current 1800ps DIMM 4 Clock fine delay...................Current 837ps DIMM 3 Control fine delay.................Current 786ps DIMM 4 Control fine delay.................Current 124ps Ch 2 Command fine delay...................Current 24ps Ch1Ch2 CommonClock Setting................More Aggresive Ch1 RDCAS GNT-Chip Delay..................Auto Ch1 WRCAS GNT-Chip Delay..................Auto Ch1 Command to CS Delay...................Auto Ch2 RDCAS GNT-Chip Delay..................Auto Ch2 WRCAS GNT-Chip Delay..................Auto Ch2 Command to CS Delay...................Auto
Intel i7 920 d0 @ 4410MHz @ 1.36v :: Prolimatech Mega Shadow :: Gigabyte EX58-UD5 F9K :: 6GB Mushkin XP3-15000 :: HIS 5870 :: Corsair 1000W :: HannsG 27.5" :: Lian Li V1010B
wait... how did you do that with special vid add i thought you could only add special vid with more than 1.2volts?? if i go below 1.2vcore than i cant use the special vid??? so how is that possible for you??
upgrading...cooler master cm690 case, corsair hx850, samsung 1tb x 3, optiarc burners x2, gskill 4gb ripjaws, working on the rest again
No idea. It just works.I'm using the 30/05 beta.
If i use 1.2v instead of auto then setting any special add that will go above 1.3v will result in a no post for me. I can only increase voltage over 1.3v with the VID set to Auto.
Intel i7 920 d0 @ 4410MHz @ 1.36v :: Prolimatech Mega Shadow :: Gigabyte EX58-UD5 F9K :: 6GB Mushkin XP3-15000 :: HIS 5870 :: Corsair 1000W :: HannsG 27.5" :: Lian Li V1010B
hmm maybe ill put mine back to auto and use the full add vid feature..but i cant pick add vid unless i set it to 1.2 or higher?? the feature is physically disabled
i wonder if i can drop the voltage some
upgrading...cooler master cm690 case, corsair hx850, samsung 1tb x 3, optiarc burners x2, gskill 4gb ripjaws, working on the rest again
As we all know, ever since the release of the DFI P35 Cell Shock PC28000 4-4-4-12 memory has been hit n' miss on DFI boards. As good as the memory is 1060MHz - 1080MHz was about tops regardless of voltages or timings. Oskar had done several alpha BIOS releases but nothing really improved.
Things are a bit different now with the release of the 07/14 BIOS. By allowing manual manipulation of DS/DDS and the DLL Modes the board can be tuned for just about any memory. The following screenshots are the first time my Cell Shock sticks have seen anything over 1100MHZ since the P965 board.
Once again Oskar, job well done.
DFI LP UT X48-T2R, 07/14 BIOS
500x8, Memory 1200MHz
E8400
2x1GB Cell Shock PC2-8000 1000MHz 4-4-4-12
OCZ Core SSD - Operating System
2x Hitachi SATA RAID 0 - Aplications/Storage
SAPPHIRE 4870
Green Slots Used For Memory
click for larger image
click for larger image
click for larger image
click for larger image
Code:CPU Feature Page Thermal Management Control................Enabled PPM (EIST) Mode...........................Enabled Limit CPUID MaxVal........................Disabled CIE Function..............................Auto Execute Disable Bit.......................Enabled Virtualization Technology.................Enabled Core Multi-Processing.....................Enabled Main BIOS Page Exist Setup Shutdown......................Mode 2 Shutdown After AC Loss....................Disabled O. C. Fail Retry Counter..................0 CLOCK VC0 Divider.........................Auto CPU Clock Ratio...........................8x CPU N/2 Ratio.............................Disabled CPU Clock.................................500 MHz Boot Up Clock.............................Auto DRAM Speed................................333/800 PCIE Clock................................100MHz PCIE Slot Config..........................1X 1X CPU Spread Spectrum.......................Disabled PCIE Spread Spectrum......................Disabled SATA Spread Spectrum......................Disabled Voltage Setting Page CPU VID Control...........................Auto 1.2200V CPU VID Special Add Limit.................Disabled CPU VID Special Add.......................108.74% DRAM Voltage Control......................2.100V SB Core/CPU PLL Voltage...................1.510V NB Core Voltage...........................1.530V CPU VTT Voltage...........................1.180V VCore Droop Control.......................Enabled Clockgen Voltage Control..................3.45V GTL+ Buffers Strength.....................Strong Host Slew Rate............................Strong GTL REF Voltage Control...................Disabled CPU GTL 1/2 REF Volt......................113 CPU GTL 0/3 REF Volt......................100 North Bridge GTL REF Volt ................100 DRAM Timing Page Enhance Data Transmitting.................Fast Enhance Addressing........................Fast T2 Dispatch...............................Enabled Clock Setting Fine Delay..................Listed Below CAS Latency Time (tCL)....................5 RAS# to CAS# Delay (tRCD).................5 RAS# Precharge (tRP)......................5 Precharge Delay (tRAS)....................15 All Precharge to Act......................4 REF to ACT Delay (tRFC)...................30 Performance Level.........................8 Read Delay Phase Adjust...................Listed Below MCH ODT Latency...........................1 Write to PRE Delay (tWR)..................14 Rank Write to Read (tWTR).................11 ACT to ACT Delay (tRRD)...................3 Read to Write Delay (tRDWR)...............8 Ranks Write to Write (tWRWR)..............4 Ranks Read to Read (tRDRD)................5 Ranks Write to Read (tWRRD)...............4 Read CAS# Precharge (tRTP)................3 ALL PRE to Refresh........................4 Read Delay Phase Adjust Page Channel 1 Phase 0 Pull-In.................Auto Channel 1 Phase 1 Pull-In.................Auto Channel 1 Phase 2 Pull-In.................Auto Channel 1 Phase 3 Pull-In.................Auto Channel 1 Phase 4 Pull-In.................Auto Channel 2 Phase 0 Pull-In.................Auto Channel 2 Phase 1 Pull-In.................Auto Channel 2 Phase 2 Pull-In.................Auto Channel 2 Phase 3 Pull-In.................Auto Channel 2 Phase 4 Pull-In.................Auto Clock Setting Fine Delay Page DRAM CLK Driving Strength............... Level 6 DRAM Data Driving Strength................Level 8 Ch1 DLL Default Skew Model................Model 5 Ch2 DLL Default Skew Model................Model 5 Fine Delay Step Degree....................5ps Ch1 Clock Crossing Setting................More Aggresive DIMM 1 Clock fine delay...................Current 1628ps DIMM 2 Clock fine delay...................Current 434ps DIMM 1 Control fine delay.................Current 578ps DIMM 2 Control fine delay.................Current 523ps Ch 1 Command fine delay...................Current 578ps Ch2 Clock Crossing Setting................More Aggresive DIMM 3 Clock fine delay...................Current 345ps DIMM 4 Clock fine delay...................Current 389ps DIMM 3 Control fine delay.................Current 612ps DIMM 4 Control fine delay.................Current 534ps Ch 2 Command fine delay...................Current 612ps Ch1Ch2 CommonClock Setting................More Aggresive Ch1 RDCAS GNT-Chip Delay..................Auto Ch1 WRCAS GNT-Chip Delay..................Auto Ch1 Command to CS Delay...................Auto Ch2 RDCAS GNT-Chip Delay..................Auto Ch2 WRCAS GNT-Chip Delay..................Auto Ch2 Command to CS Delay...................Auto Common CMD to CS Timing...................Auto
click for larger image
XP SP3
click for larger image
click for larger image
3dx Max w/V-ray
Time to render: 14min 19sec
click for larger image
click for larger image
Vista 64 Bit SP1
click for larger image
click for larger image
click for larger image
click for larger image
3dx Max w/V-ray
Time to render: 15min 39sec
click for larger image
click for larger image
The Special VID add was disabled below 1.3v, because of some instability. This was addressed in some bios update by DFI. The newest BIOSes have this setting fixed. That's how I recall it. So in essence, you're risking your CPU and MB using an older BIOS and the special VID add.
Q6600 (IHS removed) @ 3600 MHz 1.408v
DFI LanParty LT x48-T2R (1224 LT ICH9R modded bios)
4 GB Transcend Jetram @ 400 MHz 5-5-5-16 2T 1.872v
Sapphire HD4850x2 710 / 1075 MHz
PC-Power & Cooling Turbo-Cool 1kW PSU
2* OCZ Vertex2 extended 60GB @ raid0 @ ICH9R
5* Seagate 7200.11 1.5TB @ raid5 @ Promise EX8350 PCI-e RAID card
Dimastech Easy v2.5 bench table
DELL 3008WFP 30" + 2* Eizo Flexscan L887 20,1" (pivot)
Windows 7 x64
CPU EK Supreme Acetal LT | NB Swiftech MCW30 | GPU 2* Swiftech MCW60 | PUMP Phobya 400 | RAD DIY monster outside the house | TUBING 1/2" ID
Praz: I see you use Host Slew Rate strong! I have allways used weak. What does it improve?
i7 2600k @ 4.5GHz, 1.29V
Asus Maximus IV Extreme-Z (bios 0706)
8GB Ceil Corsa 2133MHz cl9
Asus GTX580
2x OCZ ve3 120Gb Max Iops (Raid0)
1x WD Black 1Tb
Asus Xonar Essence STX
NEC 24WMGX3
Corsair AX1200W
Lian-Li P80 A.S
At times setting Strong brings stability to 45nm dual core processors when approaching 500+ FSB without the need to increase NB or VTT voltages. If GTLREF values are being manually set usually this setting will make no difference. This is assuming the values are being set correctly.
^^ thanks for the explanation praz. im learning to like this mobo and still learning what everthing extra is for i have the template ill post i forgot to do it yesterday ill do it when i get home today
upgrading...cooler master cm690 case, corsair hx850, samsung 1tb x 3, optiarc burners x2, gskill 4gb ripjaws, working on the rest again
any1 tried 725 alrdy?
• DFI Lanparty LT X48-T2R
• Intel Q6600 L737B242 ~ VID 1.2125 ~ 4000mhZ @ 1.48 vcore {lapped}
• eVGA 8800GTS (G92) 512MB {stock}
• Crucial Ballistix PC8500 Tracer ~ 1200mhZ 5-5-5-12 @ 2.05v
• Lian Li PC-V1000 {modded}
• Corsair HX 620W
• Creative X-FI ExtremeMusic
• Western Digital Raptor X 150GB
• Thermalright-Ultra120 Xtreme {lapped} ft. Scythe S-Flex SFF21F S-FDB ~ Push & Pull
i woulda tried it but seems it was takin down
i thing they gonna fix somethin in it
maximus IV extreme
gigabut p67-ud7
p67 sabertooth
2500k+2600k
antec 1200watt
EVGA classified 760
920 Batch# 3849B018 4.985ghz@1.52vgtx285 ftw sli
OCZ3RPR1866LV6GK hypers
dfi ut p35
gigabut p35c-ds3r
gigabut x38-d6q
ballistix 85001240mhz@2.02v
Intel Xeon E3-1275 v2, ASUS P8Z77 WS, Kingston KHX16C9K2/16X, Zotac GTX 570 AMP!, SB X-Fi Titanium, AVerTV Hybrid Speedy PCI-E, Intel SSD 330 120GB, WD1500HLFS, WD7501AALS, Pioneer BDC-S02BK, Pioneer BDR-207DBK, Corsair HX1000W, Lian Li PC-A79B (noise insulated), 6x Noctua NF-S12A FLX, Corsair H100i, Corsair K70, Razer DeathAdder, Eizo S2431 WH-BK, Teufel Motiv 5
Thanks for the link
ASUS RANGER VII
i7 4790K
8GB CORSAIR 1600 xmp
BE QUIET SHADOWROCK SR1
EVGA GTX 770
2 X 840 EVO SSD
CORSAIR AX850W
thanks bud
i'll be sticking to 603 bios
either its my cpu or my board that dont like the bios
i wish 1 of em would just die already
damn no e8600 in canada yet
maximus IV extreme
gigabut p67-ud7
p67 sabertooth
2500k+2600k
antec 1200watt
EVGA classified 760
920 Batch# 3849B018 4.985ghz@1.52v
OCZ3RPR1866LV6GK hypers
dfi ut p35
gigabut p35c-ds3r
gigabut x38-d6q
ballistix 8500
Ok i want to flash to this 725 BIOS, what is the proper way of clearing CMOS? ( if need to use jumpers, where are those located on this board?)
And do I need to clear the CMOS after/before ( or both) Flash.
• DFI Lanparty LT X48-T2R
• Intel Q6600 L737B242 ~ VID 1.2125 ~ 4000mhZ @ 1.48 vcore {lapped}
• eVGA 8800GTS (G92) 512MB {stock}
• Crucial Ballistix PC8500 Tracer ~ 1200mhZ 5-5-5-12 @ 2.05v
• Lian Li PC-V1000 {modded}
• Corsair HX 620W
• Creative X-FI ExtremeMusic
• Western Digital Raptor X 150GB
• Thermalright-Ultra120 Xtreme {lapped} ft. Scythe S-Flex SFF21F S-FDB ~ Push & Pull
look at the manual that came with your board.
Asus Z9PE-D8 WS with 64GB of registered ECC ram.|Dell 30" LCD 3008wfp:7970 video card
LSI series raid controller
SSDs: Crucial C300 256GB
Standard drives: Seagate ST32000641AS & WD 1TB black
OSes: Linux and Windows x64
just go into bios n clear it
maximus IV extreme
gigabut p67-ud7
p67 sabertooth
2500k+2600k
antec 1200watt
EVGA classified 760
920 Batch# 3849B018 4.985ghz@1.52v
OCZ3RPR1866LV6GK hypers
dfi ut p35
gigabut p35c-ds3r
gigabut x38-d6q
ballistix 8500
Has any1 seen this b4 ??? it happened when i tried to get in the bios.
ASUS RANGER VII
i7 4790K
8GB CORSAIR 1600 xmp
BE QUIET SHADOWROCK SR1
EVGA GTX 770
2 X 840 EVO SSD
CORSAIR AX850W
Hey wilson was that after the 725 flash
• DFI Lanparty LT X48-T2R
• Intel Q6600 L737B242 ~ VID 1.2125 ~ 4000mhZ @ 1.48 vcore {lapped}
• eVGA 8800GTS (G92) 512MB {stock}
• Crucial Ballistix PC8500 Tracer ~ 1200mhZ 5-5-5-12 @ 2.05v
• Lian Li PC-V1000 {modded}
• Corsair HX 620W
• Creative X-FI ExtremeMusic
• Western Digital Raptor X 150GB
• Thermalright-Ultra120 Xtreme {lapped} ft. Scythe S-Flex SFF21F S-FDB ~ Push & Pull
So just pressing reset and power in for 5 secs.
havent seen that option yet
But do u guys Clear CMOS after/before ( both) flash?
• DFI Lanparty LT X48-T2R
• Intel Q6600 L737B242 ~ VID 1.2125 ~ 4000mhZ @ 1.48 vcore {lapped}
• eVGA 8800GTS (G92) 512MB {stock}
• Crucial Ballistix PC8500 Tracer ~ 1200mhZ 5-5-5-12 @ 2.05v
• Lian Li PC-V1000 {modded}
• Corsair HX 620W
• Creative X-FI ExtremeMusic
• Western Digital Raptor X 150GB
• Thermalright-Ultra120 Xtreme {lapped} ft. Scythe S-Flex SFF21F S-FDB ~ Push & Pull
Posting Permissions
Reply With Quote
Bookmarks