thanks godmod
tim its not to bad to remove just some wire wool
adam i was going to put a water dsh in the first stage for when it gets to hot here in the summer
but changed my mind when i got the smalled candenser you can see for nothing
from an old cooler
i will be able to turn the fan on and off on the dsh if its to cold out or winter
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
amazed!from what he did till now(the way is perfectly looking) he must have check it for leaks
congrats!
bend perfection
It looks cold bazx
Superb work Baz, cant wait to see it running
This is just looking to good baz, i will have to work harder now i have seen this work, well done mate it's looking Ace.
Very good build and well thought out, well done!
I guess my next statement is all down to personel taste. The yellow pipework looks ming.
beautiful, beautiful... sub'd
"Monolith" - [ Xeon W3540 (4.22) - Rampage 2 Extreme - 12 GB Ripjaws 1600 - GTX 570 - 120 GB OCZ Vertex - Antec TruePower 750W - Corsair 700D - Apogee XT CPU Block - XSPC 360 Rad ]
Old Box - [ E4600 2.4 @ 3.7ghz (11x335) - P5W-DH - 4gb Gskill @ 893mhz - Radeon 3850 ]
i see where your coming from... but i think the blue/yellow go together wonderfully. if it was not cased i think it would look silly, but idk how to say it... just looks so innovative i guess.Originally Posted by barbus
great work mate
mentally confused and prone to wandering
Too sick, Way too sick!
Very nice Berrie.
hope you dont mind i have used your evap mount for toms v-8 evap
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
Ooh...prettiness battle comin up between the masters?
hehe coming upOoh...prettiness battle comin up between the masters?
its been going on for 2 months now
and tbh paul has me beat when it comes down to fine detail
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
Absolutely not
cheers ericAbsolutely not
hehe did not expect to be able to use the removable electrical control box so soon
there has been a delay in my plans as the first stage compressor failed to work
but the two weeks while i waited for the new unit were not wasted as i rewired my shed and upgraded the power supply also managed to brase up the evaporator and cut down my work bench to allow me to push the cascade in the same spot where cascade 4 used to sit
also fitted the solenoid for the hot gas by-pass to the evap
the evap next to toms V8-R is a chilly clone i included a shot just to show how big the v8 evap really is
Last edited by bazx; 07-13-2008 at 12:45 PM.
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
shot of the hot gas by-pass solenoid this ill allow me to "warm up" the evap to get past any cold boot problems by just pressing a button hot gas will be taken from before the hx and piped straight to the evap face
gassed the first and second stage also
as you can see the the panel xt120c with pt100 prob are around 10c out to my fluke with k prob mounted in the same location
nice to see some frost on the unit @last
Last edited by bazx; 07-13-2008 at 12:58 PM.
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
Nice one baz, all starting to come together now, not long now before we start to see some ice on that amassing evap that Tom made, I just cannot wait to see what she can do.
you would not believe how much noise this thing makes i will need ear protection
the last stage is going to take a bit of time to tune
i will put the hot by-pass cap tube and the liquid line cap on tomorrow night
and mount the line set then probably gas the the third stage tuesday
after that it will be down to load testing and adjusting the cap tube length for the the evap which is the bit that will take the time
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
Awesome job, the only thing that I have against it is that it's ment to be "mobile".
It isn't very mobile when you need three large power sockets wherever you park it. :P
thanks for the kind words lads and sorry for not keeping this up to date i have had an event here i34 that just about sucked the last of my strength
update:
after alot of work i failed to get the unit working on R14 (this is the gas that would give me -130) so to get the unit working for i34 i put in R1150
which is giving me a solid -107 loaded
i will stick with this gas for now as i want to bench for a while
i have a few ideas on how to get the r14 working but it can wait for a month now
just been setting up a rampage extreme with a 8600 for the weekend so will have some fun on my own for a change
just had 620fsb out the box on stock air so its looking good
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
wait- ive been following this thread but i appear to have missed this-
r404a on first(or 507a w/e) but r23 on second? r1150 on third? what kind of capacity are you getting with ethylene on the third?
mentally confused and prone to wandering
Insane capacity, it's going to be rather low pressure though I imagine.
EDIT: Like I said at Benchtec Bazx, your long liquid run is dooming you I think.
Last edited by n00b 0f l337; 08-13-2008 at 11:21 PM.
If you have a cooling question or concern feel free to contact me.
507tev, 23tev, 1150 cap
this is the setup as of now
nol i want to mount a modded tev for the r14 on the back of the evap some how so that will take a bit of work
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
I don't suggest it, an even larger liquid line? No way. You should be out the bottom of the plate hx, and right to your evap.
I know you want that quick change box, so maybe move it much closer, or run 1/8" tube or something from plate hx to the box.
If you have a cooling question or concern feel free to contact me.
there will be problems with this for sure but i want to try any how
i will set-up a test evaporator first just for the experiments
the pipe work will have to change from the hx to the mount box i would also think
i enjoy this part of cascade building the most, trying different solution
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
I totally understand, my favorite part too
If you have a cooling question or concern feel free to contact me.
Posting Permissions
Reply With Quote
Bookmarks