**Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread**

[vortex240]

hey guys I got an e8400 that will do 4.3@1.45v no problem, on air. It can post 560fsb. Problem is that it is at performance level 8,only level 9 makes it stable for prime 95, however, the tv tuner frezes no mater what on my x1900 aiw atfter about 5 min if the fsb is more the 475. Increasing the voltages ( cpu, nb, vtt+gtl doesnt help). pcix is at 100

btw that is at 1:1, the 333/800 lets me run my 4gb gskill 1066 at 1121 @2v(5,5,3,15 trfc 48) and fsb is 467 1.5v nb, 1.17v vtt, gtl strong 58 60 58)
should I rma the board?
Wojtek

[Sadhana]

Is there any incompatible issue between G.Skill F2-8500CL5D-4GBPK and LPUT P35 ? I hardly to passed stable oc like I used before with my 2gb kit D9GMH. My proc is E8200 and use Vista x64. I Look back this thread and found what Praz shared with his GBPQ version, and those setting isn't work with my GBPK

[=[PULSAR]=]

Not sure if this is a place for my problem. I have 3870's in crossfire that have been flashed to increase max core from 885mhz. Problem is both cards are flashed but I can only go over 885mhz with the card that is in Bus 1(PCI-E x16 @ x16) not Bus 2(PCI-E x16 @ x4). Any ideas on how to fix it? Is it a motherboard issue?

[mrcape]

the p45 commin soon doubt they be makin any more hey it might be as good lol

I'm betting on the UT P45 T3R to be an awesome board too. But you never know.

[zsamz_]

I'm betting on the UT P45 T3R to be an awesome board too. But you never know.

its just so hard to beat this board right now

[mrcape]

Anyone ever flashed from new to an old bios ver on this board? I want to step back to 3/17 to compare a few things. Before I do that I wanted to check and see if anyone has had issues rolling back on this board.

[kitfit1]

Anyone ever flashed from new to an old bios ver on this board? I want to step back to 3/17 to compare a few things. Before I do that I wanted to check and see if anyone has had issues rolling back on this board.

No problems at all.

[mrcape]

Tx for the quick response Kitfit1 !

[Alex-Ro]

yeap,go straight and flash it.

[cantankerous]

you will have no problems at all. Just curious however, are you flashing back from 502 or 521? If so, any reason why?

[zsamz_]

Anyone ever flashed from new to an old bios ver on this board? I want to step back to 3/17 to compare a few things. Before I do that I wanted to check and see if anyone has had issues rolling back on this board.

i put an x-38 chip in mine n flashed it to latest bios lol

[mrcape]

you will have no problems at all. Just curious however, are you flashing back from 502 or 521? If so, any reason why?

From 5/21. Not sure if there's a major difference, but I want to go back and be sure, and take note of it.

5/21 is working just fine with all of my hardware and cmos profiles. The one thing I did notice (and want to confirm) was that 3/17 applied .02 less vcore at idle in windows, for the same amount set in bios (same profile). Not that that's a big deal at all, it seems to be that a range shifted slightly is all. In other words, with 5/21 I had to adjust down a few bumps to get the same idle vcore I got in 3/17.

Also I sorta jumbled the 5/21 I'm currently running testing high fsb. I got some scrambled cmos codes, reset, got em again, reset, boot up fine. I know I need to reflash something, so now is a goot time to check 3/17 again.

[cantankerous]

From 5/21. Not sure if there's a major difference, but I want to go back and be sure, and take note of it.

5/21 is working just fine with all of my hardware and cmos profiles. The one thing I did notice (and want to confirm) was that 3/17 applied .02 less vcore at idle in windows, for the same amount set in bios (same profile). Not that that's a big deal at all, it seems to be that a range shifted slightly is all. In other words, with 5/21 I had to adjust down a few bumps to get the same idle vcore I got in 3/17.

Also I sorta jumbled the 5/21 I'm currently running testing high fsb. I got some scrambled cmos codes, reset, got em again, reset, boot up fine. I know I need to reflash something, so now is a goot time to check 3/17 again.

Thanks for the explanation. I was thinking of going to 5/21 so wanted to hear your opinion on it. When it comes to the slightly higher vcore, was vcore set it in bios itself, or did you have vcore on auto but adjusted using the special % option?

[JGKC9AYC]

OK...I just got one of these & have a question (since I don't really have time to go through 189 pages...please forgive my laziness).
I'm getting ready to put this in a Stacker 832 w/a Corsair 520HX PSU. I'll have 3 of the 4 fans installed on the side panel (cannot install the 4th due to my HSF...a Xigmatek HD-S1283).
The "Transpiper" system...is it worth the time to install?
I'm currently running an E6300, but have a BNIB Q6700 that I may install. If I do, will the 520HX be enough? My other components are a XFX 7900GT, WD640GB hdd, a pair of Samsung SH-S203B's, 6x120mm fans & a fan rheostat.
That's all the questions I have for now, but i'm sure after I get it fired up, i'll have more.
Thanks!

[mrcape]

Thanks for the explanation. I was thinking of going to 5/21 so wanted to hear your opinion on it. When it comes to the slightly higher vcore, was vcore set it in bios itself, or did you have vcore on auto but adjusted using the special % option?

The vcore was set manually with no special add. And yes vcore amount manually set in 3/17 definitely applies less voltage by .02v.

So it was all a success. Thanks for confirmation that rolling back works. I've had a Brother Esau bios chip on hand for months and had no need to use it yet. I have OC'd the crap out of it hundreds of different ways and was sure by now I'd fry that chip. This board is a just a tank!

[fireice2]

The P45 TR2 board looks pretty much the same as the P35. I guess I won't be itching for an X48 and a P45. hehehe

[zsamz_]

The P45 TR2 board looks pretty much the same as the P35. I guess I won't be itching for an X48 and a P45. hehehe

you must know the p35 is better

[mrcape]

P45 TR3 would be nice though.

[zsamz_]

P45 TR3 would be nice though.

ya but i got too much ddr2 lol n i always buyin more
but i will buy the ut p45 1000%

[Kean]

There will be LanParty UT P45 DDR2? I saw only DK with DDR2 :/

[Alex-Ro]

For sure it will be both LT and Ut,unfortunately DFI is late again with 2 months,just hoping that those boards will rock

[JGKC9AYC]

Well, I got my UT P35 installed in my case & everything hooked up. I hit the power button, it ran for about 3 seconds, shut off, restarted, ran for about 2 seconds, shut off, etc. No post, didn't even run long enough to turn the power LED on my monitor from amber (standby) to green (power).
I reset everything I could reset, reseated everything that could be reseated, but still no go.
I know the ram & the video card that are in there are good as they just came off my previous motherboard.
Ideas? Suggestions?
Thanks.

[Praz]

Well, I got my UT P35 installed in my case & everything hooked up. I hit the power button, it ran for about 3 seconds, shut off, restarted, ran for about 2 seconds, shut off, etc. No post, didn't even run long enough to turn the power LED on my monitor from amber (standby) to green (power).
I reset everything I could reset, reseated everything that could be reseated, but still no go.
I know the ram & the video card that are in there are good as they just came off my previous motherboard.
Ideas? Suggestions?
Thanks.

OK...I just got one of these & have a question (since I don't really have time to go through 189 pages...please forgive my laziness).

As you listed none of your components it's doubtful anyone can give a definitive answer. Sounds like it could be a common issue that's easy enough to solve though. The answer is in this thread. Too bad you really didn't have time to go through it.

[Jupiler]

Try reseating your cpu.
I had the same thing happen a couple of weeks ago after swapping cpu's (from E8400 to X3350).
Reinstalled the E8400 and all went fine.

Be sure to clear CMOS (both the blue and red jumper) before installing your cpu.

[doakh]

I reset everything I could reset, reseated everything that could be reseated, but still no go.
I know the ram & the video card that are in there are good as they just came off my previous motherboard.
Ideas? Suggestions?
Thanks.

Just because your ram worked in another motherboard does not mean it will automatically work in this one.