"ASUS P5Q Deluxe discussion".

**Leeghoofd** · 06-13-2008, 08:37 AM

Originally Posted by R@ptor =]]

Sorry for the question...
but what is the stock volt of north?

Think 1.1 mate, but I run it at 1.2 (for the 4gb) at 400FSB daily/ram at 1066Mhz

**Chura** · 06-13-2008, 08:39 AM

I have almost setup like you, but P5Q-E (0702), and QX9650 with Scynth Ninja plus.
however every time i try to OC i get no POST and need clear cmos.

I'm familier with P5B-DLX OC, but here its so diffrent, can you give me guide lines please ?

**_sindre_** · 06-13-2008, 08:44 AM

Well, I've used some hours tweaking Skew. There is one skew setting for eatch DIMM. On my ballistix 200ps delay was the best setting, but this may be different for your system. You simply have to test all settings for finding the best. When it comes to nb and cpu skew, I've not tweaked these yet.

**Richard Dower** · 06-13-2008, 08:48 AM

Guys, with the latest bios, what version number do y'all have with regards the embedded Intel Matrix RAID option bios ROM?, 8.5.0.xxxx etc?...any version number for the Jmicron ROM?

**Ashura** · 06-13-2008, 08:50 AM

Originally Posted by Leeghoofd

CPU Voltage: 1.25
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.6
FSB Termination Voltage: 1.2
DRAM Voltage: 2.3
NB Voltage: 1.5
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal

BUT AGAIN THIS IS NOT STABLE

Do you have cooling on your NB or can it handle those volts passive?

**Chura** · 06-13-2008, 08:51 AM

Originally Posted by Richard Dower

Guys, with the latest bios, what version number do y'all have with regards the embedded Intel Matrix RAID option bios ROM?, 8.5.0.xxxx etc?...any version number for the Jmicron ROM?

0702 for the bios

**Leeghoofd** · 06-13-2008, 08:53 AM

Originally Posted by Ashura

Do you have cooling on your NB or can it handle those volts passive?

BIG 25Cm fan in the sidepanel mate and WC for the CPU...

Originally Posted by Chura

I have almost setup like you, but P5Q-E (0702), and QX9650 with Scynth Ninja plus.
however every time i try to OC i get no POST and need clear cmos.

I'm familier with P5B-DLX OC, but here its so diffrent, can you give me guide lines please ?

PHP Code:


JumperFree Configuration Settings

AI Overclock tuner: Manual

CPU Ratio Setting: 9

FSB Strap to North Bridge: AUTO

FSB Frequency: 400

PCI-E Frequency: 101

DRAM Frequency: 800 or 1000



DRAM Timing Control: AUTO



DRAM Static Read Control: Disabled

DRAM Read Training: AUTO

MEM. OC Charger: AUTO

AI Clock Twister: AUTO

AI Transaction Booster: AUTO





CPU Voltage: 1.30

CPU GTL Voltage Reference (0/2): AUTO

CPU GTL Voltage Reference (1/3): AUTO

CPU PLL Voltage: 1.5

FSB Termination Voltage: 1.2

DRAM Voltage: 2.0-2.2

NB Voltage: 1.2

NB GTL Reference: AUTO

SBridge Voltage: AUTO

PCIE SATA Voltage: AUTO



Load Line Calibration: Enabled

CPU Spread Spectrum: Disabled

PCIE Spread Spectrum: Disabled

CPU Clock Skew : Normal

NB Clock Skew : Normal



Advance CPU Settings

CPU Ratio Setting: Manual

CPU VID: Default

C1E Suppport: Disabled

Max CPUID Value Limit: Disabled

Intel&#174; Virtualization Tech: Disabled

Vanderpool Technology: Disabled

CPU TM Function: Disabled

Execute Disable Bit: Disabled

Try these settings first mate... your CPU prolly can do 3.6Ghz lower than 1.3Vcore but some have really bad ones so if you know it can do 3.6Ghz at 1.2 set 1.2 then instead off 1.30... once you get this stable you can up the multi and add more Vcore... and tweak RAM... but do it all one step at a time and use the OC profile... if it posts save it to the profile, set abother setting, save and reboot if it posts save again to the profile... it needs some time to adjust from 965 to P45...

And if it doesn't post, no need to clear CMOS... switch off the PSU.. wait a few secs , switch it back on and start the pc... it should post then..

Good luck

**jozzy** · 06-13-2008, 10:58 AM

is it my bad cpu? i can only get this high with my P5Q3 Dlx

http://valid.x86-secret.com/show_oc.php?id=374749 591 fsb

while others can easily play 600

**Leeghoofd** · 06-13-2008, 11:06 AM

Originally Posted by jozzy

is it my bad cpu? i can only get this high with my P5Q3 Dlx

http://valid.x86-secret.com/show_oc.php?id=374749 591 fsb

while others can easily play 600

Prolly await a new bios release mate... at the moment the DDR2 versions rocks, hopefully yours too soon...

**LUCI5R** · 06-13-2008, 12:20 PM

Help Guys!!

I just setup my system, and after the usual bios post (where it tells you CPU, RAM & Bios stuff), it goes to this:

"Marvell 88SE61xx Adapter - BIOS Version 1.1.0.L70d
Initializing."

And it's stuck there!!! I can't even get into BIOS. Even if I hit "DEL to enter Setup" - it goes to this and gets stuck!!!
Help!

**Leeghoofd** · 06-13-2008, 12:23 PM

Pull out one Dimm, unhook all drives (HD, DVD, etc) and try again... if it doesn't post completely don't reset, just pull the power cable... wait a few secs and then try to boot again...

**irev210** · 06-13-2008, 12:39 PM

Originally Posted by Leeghoofd

Prolly await a new bios release mate... at the moment the DDR2 versions rocks, hopefully yours too soon...

the 702 bios stinks for me

400MHz strap on dual core = broken

quad core CPU's do not function period anymore

back on original ship bios... frustrated!

Typical ASUS. Give the board a month and BIOS will have 15 new revs and finally be stable.

**Tony** · 06-13-2008, 01:00 PM

Originally Posted by irev210

the 702 bios stinks for me

400MHz strap on dual core = broken

quad core CPU's do not function period anymore

back on original ship bios... frustrated!

Typical ASUS. Give the board a month and BIOS will have 15 new revs and finally be stable.

Flash the bios, then pull the battery for 20 mins to ensure a thorough cmos clear, it should then work ok

**STaRGaZeR** · 06-13-2008, 01:19 PM

Tony have you tried the OCZ FlexII 2x2GB kit on this board?

**iboomalot** · 06-13-2008, 01:38 PM

Just put together a P5Q dlx with a 8400 wolfe and the thing won't boot

put in one stick of ram in the yellow slot nearest to CPU and have a single card in the PCI slot

have a new ZM1000-HP power supply.

everything powers up but the GPU fan just goes full blast and doesn't post

now since I bought a Lainli case the 8pin CPU power won't reach but I used a 4pin extender that came with the case.

I talked to a buddy he said it should power up on a 4pin plug and the 8pin had 1/2 coved via a plastic cover.

any ideas on what to do??

**Leeghoofd** · 06-13-2008, 01:48 PM

Define single card in the PCI slot, so not a PCI -E card ? did you try the mobo outside of the case ?

**R@ptor =]]** · 06-13-2008, 02:39 PM

Guys, I'm organizing the last details of the import of my P5q deluxe, and I have some questions.
How much voltage on northbridge, fsb, and cpu pll voltage i will need to set 450mhz of fsb with a 8x divider?? with my cpu (E6750)
PS: Don't need to be exact numbers, i wan't just a suggestions!
what is the options of memory divisor with this fsb?
thanks!

**irev210** · 06-13-2008, 02:44 PM

Originally Posted by Tony

Flash the bios, then pull the battery for 20 mins to ensure a thorough cmos clear, it should then work ok

thx, ill give it a shot.

400MHz strap on ship bios isnt all that hot either for E7200. The 333MHz strap works much better.

Still able to get in 480+ on ship bios on yorks, trying to find max with wolf still.

**iboomalot** · 06-13-2008, 02:45 PM

mobo in case will remove shortly

tried my old OCZ 520 and same results
tried my old X1800 and same results

Nvidia PNY - 8800GT in blue PCI

Can you mount a CPU wrong LOL Iam removing mobo see if that clears it up let you know.

**Chura** · 06-13-2008, 02:45 PM

Originally Posted by Leeghoofd

And if it doesn't post, no need to clear CMOS... switch off the PSU.. wait a few secs , switch it back on and start the pc... it should post then..

Good luck

Thanks for this helpfull tip !!!

**~~MomijiTMO~~** · 06-13-2008, 02:59 PM

They are finally showing up in Aus. $266. That's an awesome price.

**Chura** · 06-13-2008, 03:08 PM

who should i belive ?
CoreTemp VS. RealTemp ??

and what should be the max temp ? 70?

**iboomalot** · 06-13-2008, 03:47 PM

not sure what to do

took the mobo out and the case intrusion jumper was off

replaced that and still no boot

took mobo out

GPU powered, Ram installed 24pin powered , 4 pin powered = no boot

replaced 8400 with e6700 no boot

has to be something simple Iam missing or its bad out of the box

Iam going to try my P5W mobo with the 8400 and see if that will boot

**cstkl1** · 06-13-2008, 03:55 PM

Originally Posted by iboomalot

not sure what to do

took the mobo out and the case intrusion jumper was off

replaced that and still no boot

took mobo out

GPU powered, Ram installed 24pin powered , 4 pin powered = no boot

replaced 8400 with e6700 no boot

has to be something simple Iam missing or its bad out of the box

Iam going to try my P5W mobo with the 8400 and see if that will boot

clear ure cmos to boot via cpr

which is shutdown ure computer.. off ure psu.. wait for the standby light to off then restart..

**RealTelstar** · 06-13-2008, 03:57 PM

Originally Posted by MomijiTMO

I don't agree with you.

Who owns Crucial? Micron. There's just a bad batch of D9s that seem to have ended up in Tracers.

Not only in tracers, also in normal ballistix. Maybe there is more than one single batch. My 2 sticks were about 1y old and worked under specs and stil died.

Thread: "ASUS P5Q Deluxe discussion".

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions