Q9450 OC / Temps / Settings

[REVHEAD]

That is all crap talk tbh. I run mine at 450x8 24/7 and it does easy 500 fsb if I really push it to the limit. I have a Maximus X38 mobo modded with rampage 0403 bios.

Ok i am just full of it then? maybe I am just making it up for no reason? Pfft

Howabout some constructive posting like ,oh I can get mine stable @ set MHZ and actually give us some Bios settings that we can try instead, this is a feedback thread and if you have some good feedback then please dont be shy sharing your Bios settings.

[AquaRelliux]

Ok i am just full of it then? maybe I am just making it up for no reason? Pfft

Howabout some constructive posting like ,oh I can get mine stable @ set MHZ and actually give us some Bios settings that we can try instead, this is a feedback thread and if you have some good feedback then please dont be shy sharing your Bios settings.

ofc here u go it is posted before on maximus thread but here, btw worth to meantion rampage bios gave me 30 fsb boost.
Also if u are using 2x ramsticks u dont need to go more then 1.5v on the NB I have 4x sticks so that is why I use 1.65v:

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 8
FSB Frequency : 450
FSB Strap to North Bridge : 333
PCI-E Frequency: 100
DRAM Frequency: DDR2-1081
DRAM Command Rate : 2T
DRAM CLK Skew on Channel A : advance +250
DRAM CLK Skew on Channel B : advance +250
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : 5
Row Refresh Cycle Time : 55
Write Recovery Time : 6
Read to Precharge Time : 5

Read to Write Delay (S/D) : Auto
Write to Read Delay (S) : Auto
Write to Read Delay (D) : Auto
Read to Read Delay (S) : Auto
Read to Read Delay (D) : Auto
Write to Write Delay (S) : Auto
Write to Write Delay (D) : Auto

Write to PRE Delay : Auto
Read to PRE Delay : Auto
PRE to PRE Delay : Auto
ALL PRE to ACT Delay : Auto
ALL PRE to REF Delay : Auto

DRAM Static Read Control: Disabled
Ai Clock Twister : Stronger
Transaction Booster : Manual

Boost lvl: 7

All this here is disabled

CPU Voltage : 1.23750(yes it is stable 100% prime 10 hours and gaming 5 hours with 2x1gb ram it drops to 1.216v load)
CPU PLL Voltage : 1.50
North Bridge Voltage : 1.65
DRAM Voltage : 2.14(Everest says 2.19v)
FSB Termination Voltage : 1.38(Everest says 1.28 is this accurate btw? I heard 1.4v could kill it and I dont want that)
South Bridge Voltage : 1.50
Loadline Calibration : Enabled
CPU GTL Reference : Auto(Tried 0.67x but crashed in boot then and I heard before u should leave this on auto for 45nm cpus)
North Bridge GTL Reference : 0.67X
DDR2 Channel A REF Voltage : DDR2-REF
DDR2 Channel B REF Voltage : DDR2-REF
DDR2 Controller REF Voltage : DDR2-REF
SB 1.5V Voltage : 1.5

CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled