The Maximus Formula Thread - Help/OCing/Guide/Rampage conversion

[masska]

Hi guys, I've finally got my tracers back from Crucial a few days ago.And I must say these feel and behave a lot better than my original red ones (these are double sided aswell). Anyway I got a 3.6 OC quite easy (stable and OCCT),I did manage to get up to 3.8 and 3.9, however it wasn't stable. Now I dont want to keep messing arround with it too much as this is my work machine aswell, and I dont wont to corrupt the OS. So I'm looking for your help to get me up to 3.8 or 3.9. My temps are 35c idle and 60-64 stress/load @ 3.6 and almost identical at 3.9. These are my settings.

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : 9
- Ratio CMOS Setting :
FSB Frequency : 400
FSB Strap to North Bridge :400
PCI-E Frequency: 100
DRAM Frequency: DDR2-800
DRAM Command Rate : 2T
DRAM Timing Control: Manual
CAS# Latency : 4
RAS# to CAS# Delay : 4
RAS# Precharge : 4
RAS# ActivateTime : 12
RAS# to RAS# Delay : auto
Row Refresh Cycle Time : auto
Write Recovery Time : auto
Read to Precharge Time : auto

Read to Write Delay (S/D) : auto
Write to Read Delay (S) : auto
Write to Read Delay (D) : auto
Read to Read Delay (S) : auto
Read to Read Delay (D) : auto
Write to Write Delay (S) : auto
Write to Write Delay (D) : auto
DRAM Static Read Control: disabled
Ai Clock Twister : auto
Transaction Booster : disabled
Relax Level : 0
CPU Voltage : 1.44375
CPU PLL Voltage : 1.56
North Bridge Voltage : 1.51
DRAM Voltage : 2.08
FSB Termination Voltage : 1.40
South Bridge Voltage : 1.150
Loadline Calibration : enabled
CPU GTL Reference : .63x
North Bridge GTL Reference : .67x
DDR2 Channel A REF Voltage : auto
DDR2 Channel B REF Voltage : auto
DDR2 Controller REF Voltage : auto
SB 1.5V Voltage : 1.55

NB LED Selection : NB Volt
SB LED Selection : SB Volt
CPU LED Selection : CPU VOlt
Voltiminder LED : disabled

CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

Advanced CPU Configuration
CPU Ratio Control : Manual
- Ratio CMOS Setting :
C1E Suppport : Disabled
CPU TM Function : Disabled
Vanderpool Technology : Disabled
Execute Disable Bit : Disabled
Max CPUID Value Limit : Disabled


USB Configuration
USB Functions: Enabled
Legacy USB Support : Disabled

[iadstudio]

Hi guys, I've finally got my tracers back from Crucial a few days ago.And I must say these feel and behave a lot better than my original red ones (these are double sided aswell). Anyway I got a 3.6 OC quite easy (stable and OCCT),I did manage to get up to 3.8 and 3.9, however it wasn't stable. Now I dont want to keep messing arround with it too much as this is my work machine aswell, and I dont wont to corrupt the OS. So I'm looking for your help to get me up to 3.8 or 3.9. My temps are 35c idle and 60-64 stress/load @ 3.6 and almost identical at 3.9. These are my settings.

Watch the timings on the 8gb of memory. You don't want it too tight with 8gb and a serious cpu OC.