Got me a couple of Q9300's sent over from hecktic, one of them was a real dud but the other kinda compensated for that.
Vcore 1.275 bios (terrible vdrop)
FSB +0.1v
Scythe minininja with two 67CFM in push/pull.
FSB wall at 478MHz
L804B104
It really runs good on "low fat" as well
Last edited by Clint; 05-13-2008 at 11:09 AM.
GA-H55N-USB3
i3-550 L008B555 @4.6GHz (1.36v)
Sapphire HD 5850 @1GHz/1.3GHz (1.25v)
GSkill ECO 4GB PC3-12800 @1.33GHz 6-6-6-20 1T (1.34v)
470-ish FSB wall is ok because there is very marginal performance boost after 3.6ghz.
would be nicer to get higher but alas it is a quad and boards just dont have quads past the 470 mark very well.
but very nice voltages.
dont forget about PLL/VTT/FSB voltages in the bios because those WILL make your overclock require higher vcore than what it should.
proper pll/vtt/fsb voltages can make overclocking the cpu a much "cooler" experience.
"These are the rules. Everybody fights, nobody quits. If you don't do your job I'll kill you myself.
Welcome to the Roughnecks"
"Anytime you think I'm being too rough, anytime you think I'm being too tough, anytime you miss-your-mommy, QUIT!
You sign your 1248, you get your gear, and you take a stroll down washout lane. Do you get me?"
Heat Ebay Feedback
M1 revision... it has smaller die and lower VID than C0/C1
C2Q QX6800@ 3.75GHz (375x10 - 1.450v) - L725A - G0
4GB PC2-5300 Kingston Micron D9@ 3-4-4-10 750MHz 1:1
Asus P5E-Deluxe - no mods
eVGA 9600gso G92 + XFX 8500 GT (physics)
H4ck3d-Slackware 11.0
kernel-2.6.22.1@MCORE2 Arch Optimized
Yep, it's quite obvious when compared to others results with Q9300. I think I'll keep this one for a while, I really don't care about the smaller cache....can't see much performance loss in reality.Originally Posted by MarlboroMan
GA-H55N-USB3
i3-550 L008B555 @4.6GHz (1.36v)
Sapphire HD 5850 @1GHz/1.3GHz (1.25v)
GSkill ECO 4GB PC3-12800 @1.33GHz 6-6-6-20 1T (1.34v)
So you are saying that I should raise the FSB voltage even more?
I don't know, the board maxes out at 500MHz and will boot up to 460 on stock FSB voltage. From what I understand the FSB voltage is what can kill the 45nm chip?
GA-H55N-USB3
i3-550 L008B555 @4.6GHz (1.36v)
Sapphire HD 5850 @1GHz/1.3GHz (1.25v)
GSkill ECO 4GB PC3-12800 @1.33GHz 6-6-6-20 1T (1.34v)
do you have the s-spec? SLxxx??
C2Q QX6800@ 3.75GHz (375x10 - 1.450v) - L725A - G0
4GB PC2-5300 Kingston Micron D9@ 3-4-4-10 750MHz 1:1
Asus P5E-Deluxe - no mods
eVGA 9600gso G92 + XFX 8500 GT (physics)
H4ck3d-Slackware 11.0
kernel-2.6.22.1@MCORE2 Arch Optimized
It's SLAWE (Malay).
GA-H55N-USB3
i3-550 L008B555 @4.6GHz (1.36v)
Sapphire HD 5850 @1GHz/1.3GHz (1.25v)
GSkill ECO 4GB PC3-12800 @1.33GHz 6-6-6-20 1T (1.34v)
whoah... 0.896 vcore at stock speeds.... that is really nice..
should throw some water on it now...
I were also benching one pretty good Q9300 yesterday.
3720MHz with aircooling.
I upped best results to HWBOT:
PCMark05
PiFast
SuperPi 32M
wPrime 1024M
wPrime 32M
Very stable at 7.5 x 496MHz and reasonable 1.425V Vcore.
Posting Permissions
Reply With Quote
Bookmarks