D-Tek Fuzion V2 RELEASE THREAD!

[xtclocker]

Haha, yep thats what I look like right now.... pretty darn impatient!!



I'm not sure what the OC will turn out to be as I haven't had a good enough cooler to go any higher than 3Ghz, but I'm hoping for around 3.8Ghz with maybe 1.35-1.4v.
Well, I'll be testing on this system:

QX6700 ES @ Stock and OC
ASUS Striker Extreme
Corsair Dominator 2GB, 800Mhz Cas4
eVga 8800GT 512MB @ 700/1717/1003 (stock cooler)
Corsair 650w PSU

Watercooling:
Fuzion V1 and V2
Laing D5 pump
MCR320 Rad (6 50CFM fans)
Micro Res

So yes, it's a quad core system. I'll test stock and OC temps.

I'll be sure to let you guys know when my stuff comes in today!

Not bad setup.

[Giannis86]

i would just crank up the vcore at stock speeds only for some testing. I am not sure if you would be able to measure the differences easily at stock vcore seeing that the blocks are quite identical. not to mention there is also the inconsistency between mounts

[smee]

Not bad setup.

Thanks!
You can see my worklog for the build in my sig.

i would just crank up the vcore at stock speeds only for some testing. I am not sure if you would be able to measure the differences easily at stock vcore seeing that the blocks are quite identical. not to mention there is also the inconsistency between mounts

Hmmm, thats a good idea.
I'll be posting progress and things and will be asking lots of questions when I get to that point....
And I'll be doing lots and lots of mounts

[smee]

Ok guys! My board came in with the tubing!! w0000t!!

Which block should I test first?

[[XC] NetburstXE]

V2

[Giannis86]

i would say it doesnt make a difference really..we cant compare the results as every system is different. Obviously both will perform good so...

personally i would test the V1 first to have a reference.. Then you can go on with the V2 and see how it scales to V1

ps: some ambient temps along with other info etc would help a lot to analyse results

[smee]

V2

i would say it doesnt make a difference really..we cant compare the results as every system is different. Obviously both will perform good so...

personally i would test the V1 first to have a reference.. Then you can go on with the V2 and see how it scales to V1

Hmmm, well. I'll i'll do the V1 first, just so we have a base here...

ps: some ambient temps along with other info etc would help a lot^^

Here let me check, 1 sec....

[Giannis86]

Here let me check, 1 sec....

i meant when taking the readings of cpu temps

anyway i wish you lots of fun
cant wait for some results on this

[smee]

i meant when taking the readings of cpu temps

anyway i wish you lots of fun
cant wait for some results on this

Oh ok, I'll make sure to post them when I post temps.

I can't wait either!!! woot, backplates on!

[ripken204]

wow u just went to petras, saw the new block, then came here! i cant wait to see the results!
if the new block does turn out well then i will be getting one to replace my v1.

so does the v2 come with a quad core nozzle already in it? or do you have to buy separately and put it in?

[[XC] NetburstXE]

I can't wait for the results

[evil-98]

wow u just went to petras, saw the new block, then came here! i cant wait to see the results!
if the new block does turn out well then i will be getting one to replace my v1.

so does the v2 come with a quad core nozzle already in it? or do you have to buy separately and put it in?

you have to buy it separately

i expected mine to be here by now.. looks like ill have to wait one more day

[ripken204]

you have to buy it separately

i expected mine to be here by now.. looks like ill have to wait one more day

ya i see that now at petras, its cheap enough so who cares.
too bad it's out of stock.
when i redo my loop next, hopefully in a new case, i will get this.

[evil-98]

sigh.. looks like an all nighter and gallons and gallons of distilled

[DOM.]

so does anyone know if the v2 Quad Core Mid Chamber Insert works on the v1 ?

its says

•The Quad Core Insert works with the FuZion v2 only

but the Accelerator Nozzle Kit works in the v2 right ?

[ripken204]

well with all of you who have it already, COME ON!!! RESULTS!!!

[djnoob]

LOL hell I get mine tomorrow and if they don't start showing up I just might beat them to it.

[smee]

well with all of you who have it already, COME ON!!! RESULTS!!!

LOL hell I get mine tomorrow and if they don't start showing up I just might beat them to it.

Be patient people!
Testing takes a while you know.
I'm first testing the V1 first, just to get a base to start with.
So far I've done two remounts with the stock washer, testing Idle and Load temps, and I've just mounting it with the Quad nozzle and am going to test that.
Stay tuned...

[smee]

Ok, just did a second remount with the Quad nozzle.

Next should I test two mounts with the 5.5 Nozzle, or should I test the V2?
You guys decide.

[CCC]

1 vote for the V2

[smee]

1 vote for the V2

Then the V2 it is!!
First up, I'll test it Stock, straight from the factory
After two mounts with Stock, I'll try the Quad chamber mid plate, then I'll try the Quad Nozzle (from V1).
Stay tuned!!

[smee]

First test results have been POSTED!!!!
Linkage:
http://www.xtremesystems.org/forums/...68#post2968268

[djnoob]

woo hoo!!!!!

Thanks smee!!! I was just joking with ya. Hell I know this stuff takes time, and effort.

[smee]

woo hoo!!!!!

Thanks smee!!! I was just joking with ya. Hell I know this stuff takes time, and effort.

No problem m8! It's fun, but yes it does take a lot of time and work..... for those tests and a couple that haven't been released yet () it took me about 4 hours.... remounts and switching blocks take a while, plus air bubbles are a pain....

So yea, a lot of work, but I really do enjoy it!!!

[smee]

Well guys, as far as the stock block tests, the V2 holds about 4-5c better temps.
This is looking good!