Just to prove my theory that Phenom can overclock with Low Voltage and requires a light and artful Approach, heres a 4hr Prime Run.
DFI LANPARTY UT 790FX-M2R (BIOS 4/15/2008 "Beta")
AMD Phenom 9850 Black Edition "B3"
Tuniq Tower 120
OCZ Reaper HPC (PC2-8500) 5-5-5-18 2X2GB
POWERCOLOR AX3870 X2 CROSSFIRE CATALYST 8.3
Auzentech XPlosion
Areca 1231 ML {Intel IOP 341} ~ 6 ~ 250gb Hitachi Sata II Raid 6 ~2~WD 74gb Raptors ~ Raid 0 ~
Plextor 750A
SilverStone OP1000
CM Stacker STC-T01
Code:>HT Link Control: HT Link Width......................... - 16 bit HT Frequency.......................... - 2GHZ MHz IH Flow Control Mode.................. - Disabled HT Link Tristate...................... - Disabled 2x LCLK Mode.......................... - Disabled Unit Id Clumping...................... - Disabled >CPU Feature: CPU DID.............................. - 1 CPU FID.............................. - 0C CPU-NB DID........................... - 1 CPU-NB FID........................... - 06 AMD CPU stepping..................... - P0 >DRAM Configuration: MCT Memory Timing.................... - Manual 2T Mode.............................. - Auto Cas Latency Time..................... - 5 Pre Charge Delay (tRAS).............. - 18 DRAM RAS# Precharge.................. - 5 DRAN RAS# to CAS# Delay.............. - 5 Bank to Bank Cmd (TRRD).............. - Auto TRC.................................. - 23T TRTP................................. - Auto Write Recovery (TWR)................. - Auto Write-Read Command (TWTR)............ - Auto TRFC0................................ - 195ns TRFC1................................ - 195ns TRFC2................................ - 195ns TRFC3................................ - 195ns Trdrd................................ - Auto TrwtT0............................... - Auto Twrrd................................ - Auto Twrwr................................ - Auto CS/ODT Pin Fine Delay................ - Enabled Bank Swizzle Mode.................... - Enabled Auto Tweak Performance............... - Enabled Optimal Performance Mode............. - Enabled >ODC Control Mode: DRAM Drivers Weak Mode.............. - Normal Output Drivers Comp................. - Normal >Channel A: CPU On-die Termination.............. - 300 ohms +/- 20% DQS Drive Strength.................. - 1.00x Data Drive Strength................. - 1.00x MEMCLK Drive Strength............... - 1.00x Addr/Cmd Drive Strength............. - 1.50x CS/ODT Drive Strength............... - 1.50x CKE Drive Strenght.................. - 1.50x >Channel B: CPU On-die Termination.............. - 300 ohms +/- 20% DQS Drive Strength.................. - 1.00x Data Drive Strength................. - 1.00x MEMCLK Drive Strength............... - 1.00x Addr/Cmd Drive Strength............. - 1.50x CS/ODT Drive Strength............... - 1.50x CKE Drive Strenght.................. - 1.50x >PWM Settings: PWM Control.......................... - Enabled CPU VID Control...................... - 1.23750v CPU Vid Special Add.................. - Auto CPU NB Vlotage Control............... - 1.23750v CPU NB Vid Special Add............... - Auto DRAM Voltage Control................. - 1.80v SB PLL 1.2V Voltage.................. - 1.20v NB Core Voltage...................... - 1.200v NB PCI-E Voltage..................... - 1.120v NB HT Voltage........................ - 1.270v Genie BIOS Settings: Timing Mode.......................... - Manual Memory Clock value or Limit.......... - DDR 1066 PCIE 3,4 State....................... - Auto PCIE 2 State......................... - x2 CPU TLB Cache Fix.................... - Disabled AMD K8 Cool & Quiet control.......... - Disabled CPU Clock Ratio...................... - Auto Spread Spectrum...................... - Disabled CPU Host/HTT Clock................... - 200mhz CPU Host/HTT Boot Up Clock........... - 200mhz CPU Host/HTT Adjustment Gap.......... - 5mhz PCIE Clock........................... - 100mhz
Reply With Quote
Bookmarks