Rocketfish case aka Lian Li

[WesM63]

Does anyone know how well a Skulltrail board will fit in this? Or, is it deeper, in length than a Stacker 830 Evo?

Skulltrail is cram packed into my 830.

[Polizei]

Should fit E-ATX in there comfortably.

I have a regular ATX board and there is atleast 6" from the edge of my board to the edge of the 5.25" bays

[JustMe2]

I'd like to share my progress.

Yeah, the Dremal got away from me I'm thinking I might just paint the case a gloss white. Gloss white with my UV purple internals. Hmmm, project ArticFish?

[geesosa73]

Dimensions (W x H x D): 250 x 536 x 638mm Cooler Master 832

Dimensions (W x H x D): 208 x 579 x 615mm
Rocketfish Aluminum Full-Tower Case

[Daddyjaxx]

I think I got about the last one in the Atlanta area. Boy do I feel I got ripped off at the cost I actually paid with cash money too. I've paid more for POS cases from New Egg for systems I have put together for family.



The PA120.3 will fit nicely at the top even with 6 fans if I put 3 outside of the case on the top. I'm even thinking about using my MM panel as a template for a side window and fans and use the plexiglass over again.

[Lu523]

I think I got about the last one in the Atlanta area. Boy do I feel I got ripped off at the cost I actually paid with cash money too. I've paid more for POS cases from New Egg for systems I have put together for family.

I got mine at North Lake. Think they had 3 when I left.
As far a dremels go. Has any one tried the cutter that looks like a drill bit? It is the 561 MultiPurpose Cutting Bit. I have one and have thought abot trying it. Might be easier than a cutoff wheel.

[Jor3lBR]

I got mine at North Lake. Think they had 3 when I left.
As far a dremels go. Has any one tried the cutter that looks like a drill bit? It is the 561 MultiPurpose Cutting Bit. I have one and have thought abot trying it. Might be easier than a cutoff wheel.

It's a nice thing to elaborate more on how ppl are using the dremel and witch tool they are using...

Most of the courageous guys here are doing it by free hand... But I dunno If I would be so skillful with that thing at full rpm to make a perfect straight line... And the worst part is you only have 1 shot!

How about using a guided saw like this: http://www.dremel.com/en-us/attachme...=69679&I=69804

[Lu523]

Actually you would use a another attachment with the bit. http://www.dremel.com/en-us/attachme...=69679&I=69795
That would make it easier to use.

[iadstudio]

Actually you would use a another attachment with the bit. http://www.dremel.com/en-us/attachme...=69679&I=69795
That would make it easier to use.

I've tried that and those bits don't work so well on metal. If they made a carbide version it might work well.

[Jor3lBR]

Actually you would use a another attachment with the bit. http://www.dremel.com/en-us/attachme...=69679&I=69795
That would make it easier to use.

I was talking about another accessory. I really don't know how that tool in your link would help you make a straight line, but I bet that the thin case aluminum is easier to cut then that wood in the video preview.

I think this is the one your looking for:
678-01 Circle Cutter & Straight Edge Guide: http://www.dremel.com/en-us/attachme...=69679&I=69820

[Arkangyl]

Couple for $48 in Central Mass.

I have to say, I really want one of these, always loved the Lian-Li's, but I just got a CM 690...

[[XC] NetburstXE]

Couple for $48 in Central Mass.

I have to say, I really want one of these, always loved the Lian-Li's, but I just got a CM 690...

Nobody's stopping you

[[XC] NetburstXE]

Simple request for somebody with a Rocketfish case: Can you give me the measurements (L*H*W) for the rocketfish case?

[itznfb]

this is from their site:

#
Product Height
24.2"
#
Product Width
22.8"
#
Product Weight
18.6 lbs.
#
Product Depth
20.8"

[lefy]

will a pcp&c 1kw fit without having to remove that HDD tray?

[Daddyjaxx]

No way.

[[XC] NetburstXE]

this is from their site:

#
Product Height
24.2"
#
Product Width
22.8"
#
Product Weight
18.6 lbs.
#
Product Depth
20.8"

I saw that, I was just a little suspicious based on the 22.8" width

[itznfb]

oh i c.... lol

side panel to side panel = 8.25"
front to back = 24.25" (including door)
top to bottom = 22.5"

[Polizei]

No way.

I was about to say you were wrong and that there was a ton of space, but then I looked at my case and remembered I took out the hard drive cage closest to the power supply. Didn't need it.

[Jor3lBR]

will a pcp&c 1kw fit without having to remove that HDD tray?

So the answer to his question is YES it fits as long as you remove the 1st HDD cage close to the PSU (they are easily removed with screws)

You will still have 1 cage left and tons of space to add hdd's on floppy's and cd's bays...

[lefy]

maybe i don't need any of those HDD cages at the bottom. do the Lian Li HDD mount kits work with this case?

[Lurid]

maybe i don't need any of those HDD cages at the bottom. do the Lian Li HDD mount kits work with this case?

Yea, should work fine.

[JustMe2]

The window is from PPC, and it is super seXy.

Please excuse my mess in there. I was getting a feel for my new q6700. I wont finish my project until after exams. Cutting holes in mobo tray, getting LCS in there, all my new HDDs, etc etc...

[Jor3lBR]

I love that side panel, but I wish they made one like other Lian Li cases that hides the lower part that we don't need to see:



I wonder if this one is compatibe with our case.

[[XC] NetburstXE]

You could always make your own.