Crap, flashed, set everything to old settings, Prime and BSOD...
Looks like Ill have to mess around with those parameters then? If that doesnt work it will be most likely another problem then.
Anyway, how do I start from here regarding those parameters? Flash back to initial BIOS release and then back to this one?
Synaptic Overflow
CPU:
-Intel Core i7 920 3841A522
--CPU: 4200Mhz| Vcore: +120mV| Uncore: 3200Mhz| VTT: +100mV| Turbo: On| HT: Off
---CPU block: EK Supreme Acetal| Radiator: TCF X-Changer 480mm
Motherboard:
-Foxconn Bloodrage P06
--Blck: 200Mhz| QPI: 3600Mhz
Graphics:
-Sapphire Radeon HD 4870X2
--GPU: 750Mhz| GDDR: 900Mhz
RAM:
-3x 2GB Mushkin XP3-12800
--Mhz: 800Mhz| Vdimm: 1.65V| Timings: 7-8-7-20-1T
Storage:
-3Ware 9650SE-2LP RAID controller
--2x Western Digital 74GB Raptor RAID 0
PSU:
-Enermax Revolution 85+ 1250W
OS:
-Windows Vista Business x64
ORDERED: Sapphire HD 5970 OC
LOOKING FOR: 2x G.Skill Falcon II 128GB SSD, Windows 7
No its corrupted because you either flashed with the 1/30/08 or 2/7/08 Beta
Went through the same deal I would suggest you go back a few pages and read all of my posts and see if there is a similarity in you're situation compared to what I was posting. Do that first and get back to me with some feed back on your thoughts please and will advise at that point!
On a different not will be getting a Phenom 9600 BEso will help with that area with the Bios on this Board
SuperMicro X8SAX
Xeon 5620
12GB - Crucial ECC DDR3 1333
Intel 520 180GB Cherryville
Areca 1231ML ~ 2~ 250GB Seagate ES.2 ~ Raid 0 ~ 4~ Hitachi 5K3000 2TB ~ Raid 6 ~
How can I check that my BIOS is corrupted or not? I always use the Award Winfash for flashing the BIOS. I like it.Originally Posted by Brother Esau
No its corrupted because you either flashed with the 1/30/08 or 2/7/08 Beta
Stable settings that have been proven 8hrs + Prime stable on certain Bios for me it was 11/22/07 and irregardless of flashing to 11/22/07 3 times as well as other Bios it would still fail Prime within minutes at the exact same settings on the exact same bios that had been constant stable with those settings. After Flashing to and fro about 5 times I pulled my chip out of my board and put it on my Programmer and Erased/un scrambled it and programmed it with 11/7/07 and then a few hrs later at defaults I flashed to 11/22/07 Bios from DOS and proven stable settings that were stable but failed within minutes into prime 95 on 11/22/07 instantly became stable once again after Erasing & re-programming the chip on my programmer and updating Bios to 11/22/07 in DOS
So proven stable settings that have been tested extensively with a Certain Bios Release should yield the exact same result once you Flash back to that Bios if you update the Bios and find for what ever reason it does not work for you.
If that is not the case such as with me in my situation the only two conclusions I could make was Vibration damage to components from 2780 Mile Road trip in Big 26' Diesel Truck across country or Bios corruption
SuperMicro X8SAX
Xeon 5620
12GB - Crucial ECC DDR3 1333
Intel 520 180GB Cherryville
Areca 1231ML ~ 2~ 250GB Seagate ES.2 ~ Raid 0 ~ 4~ Hitachi 5K3000 2TB ~ Raid 6 ~
Posting Permissions
Reply With Quote
Bookmarks