**Official DFI LanParty UT 790FX-M2R Review/Overclock/Guide Thread**

[Brother Esau]

Well got back to 9+ hrs PRIME95 Stable with 11/22/07 Bios



DFI LANPARTY UT 790FX-M2R (BIOS 11/22/07)

AMD Athlon X64 6400+ Black Edition 3.2ghz

OCZ FLEX XLC (PC2 9200) 5-5-5-18 2 x 1GB PN:OCZ2FX11502GK

POWERCOLOR AX3870 X2 CROSSFIRE CATALYST 8.1

Auzentech XPlosion

Areca 1231 ML {Intel IOP 341} ~ 6 ~ 250gb Hitachi Sata II Raid 6 ~2~WD 74gb Raptors ~ Raid 0 ~

Plextor 230A

SilverStone OP1000

CM Stacker STC-T01

>HT Link Control:
 
HT Link Width......................... - 16 bit
HT Frequency.......................... - 800 MHz
IH Flow Control Mode.................. - Disabled
HT Link Tristate...................... - Disabled
2x LCLK Mode.......................... - Disabled
Unit Id Clumping...................... - Disabled
 
>CPU Feature:
 
NPT Fid Control....................... - x10
Virtualization........................ - Enabled
AMD K8 Cool&Quiet Control............. - Disabled

>DRAM Configuration:

MCT Memory Timing.................... - Manual
Maximum Latency...................... - 8ns
2T Mode.............................. - Auto
Cas Latency Time..................... - 5
Pre Charge Delay (tRAS).............. - 11
DRAM RAS# Precharge.................. - 5
DRAN RAS# to CAS# Delay.............. - 5
Bank to Bank Cmd (TRRD).............. - Auto
DRAM RAS# to CAS# Delay.............. - Auto
TRTP................................. - Auto
Write Recovery (TWR)................. - Auto
Write-Read Command (TWTR)............ - Auto
TRFC0................................ - Auto
TRFC1................................ - Auto
TRFC2................................ - Auto
TRFC3................................ - Auto
Trdrd................................ - Auto
TrwtT0............................... - Auto
Twrrd................................ - Auto
Twrwr................................ - Auto
CS/ODT Pin Fine Delay................ - Enabled
Bank Swizzle Mode.................... - Enabled
Auto Tweak Performance............... - Enabled
Optimal Performance Mode............. - Enabled

>ODC Control Mode:

DRAM Drivers Weak Mode.............. - Normal
Output Drivers Comp................. - Normal
>Channel A:
CPU On-die Termination.............. - 300 ohms +/- 20%
DQS Drive Strength.................. - 1.00x
Data Drive Strength................. - 1.00x
MEMCLK Drive Strength............... - 1.00x
Addr/Cmd Drive Strength............. - 1.50x
CS/ODT Drive Strength............... - 1.50x
CKE Drive Strenght.................. - 1.50x
>Channel B:
CPU On-die Termination.............. - 300 ohms +/- 20%
DQS Drive Strength.................. - 1.00x
Data Drive Strength................. - 1.00x
MEMCLK Drive Strength............... - 1.00x
Addr/Cmd Drive Strength............. - 1.50x
CS/ODT Drive Strength............... - 1.50x
CKE Drive Strenght.................. - 1.50x


>PWM Settings:
 
PWM Control.......................... - Enabled
CPU VID Control...................... - 1.4225v
CPU Vid Special Add.................. - Auto
CPU NB Vlotage Control............... - Auto
CPU NB Vid Special Add............... - Auto
DRAM Voltage Control................. - 2.12v
SB PLL 1.2V Voltage.................. - 1.20v
NB Core Voltage...................... - 1.290v
NB PCI-E Voltage..................... - 1.60v
NB HT Voltage........................ - 1.300v
[
 
Genie BIOS Settings:
 
Spread Spectrum................ - Disabled
CPU Host/HTT Clock................... - 350MHZ
CPU Host/HTT Boot Up Clock.............. - 320MHZ
CPU Host/HTT Adjust Gap..................... - 5
PCI-E Clock.................... - 100MHZ

Attachment 69418

[Brother Esau]

After proving that 11/22/07 Bios was 8+hrs Prime95 Stable and none of my hardware suffered any damage during the move back to the East Coast (God its good to be Home! ) I am currently testing the 3/12/2008 Beta Bios I'll keep you all posted wish me luck


5hr Prime95 Run same settings as 11/22/07 Template above using new 3/12/2008 Beta