Results 1 to 25 of 277

Thread: Help the newbie with his build!!

Hybrid View

  1. #1
    Xtreme Mentor
    Join Date
    Sep 2007
    Location
    Ohio
    Posts
    2,977
    More fine tuning was done on my every day 3.8GHz Bios settings.

    I primed for 2 hours using my above 3.8GHz settings, and encountered an error on 1 core. My guess was it probably was just Core voltage issue, but remember when Priming 3.9GHz I needed a wee bit more CPU PLL voltage too.

    Allot of the boy's are running more NB voltage than me and my 1.51v's, so I took that up a notch too to 1.55V's.

    I also moved my South bridge voltage from 1.05v's to 1.075v's for no good reason.

    I cutt Prime95 loose again to see if my 3.8GHz would still have an error in 2 hours. My result was an error free 4 hour run, and me adopting these new settings.
    This is what I currently run 24-7 now...

    My 4hour error free run using my 3.8GHz settings. Room temp was a brisk 55°F:


    These are my current best BIOS 907 settings for 3.81GHz:

    Under Extreme Tweaker
    Ai Overclock Tuner : Manual
    OC From CPU Level Up : Auto
    CPU Ratio Setting : 9
    FSB Frequency : 424
    FSB Strap to North Bridge : 400
    PCI-E Frequency: 110
    DRAM Frequency: DDR2-848MHz
    DRAM Command Rate : 2T
    DRAM Timing Control: Manual
    CAS# Latency : 5
    RAS# to CAS# Delay : 5
    RAS# Precharge : 5
    RAS# ActivateTime : 18
    RAS# to RAS# Delay : Auto
    Row Refresh Cycle Time : Auto
    Write Recovery Time : Auto
    Read to Precharge Time : Auto

    Read to Write Delay (S/D) : Auto
    Write to Read Delay (S) : Auto
    Write to Read Delay (D) : Auto
    Read to Read Delay (S) : Auto
    Read to Read Delay (D) : Auto
    Write to Write Delay (S) : Auto
    Write to Write Delay (D) : Auto
    DRAM Static Read Control: Enabled
    Ai Clock Twister : Strong
    Transaction Booster : Auto

    CPU Voltage : 1.51250v (BIOS)
    CPU PLL Voltage : 1.58v (BIOS)
    North Bridge Voltage : 1.55v (BIOS)
    DRAM Voltage : 1.80v (BIOS)
    FSB Termination Voltage : 1.44v (BIOS)
    South Bridge Voltage : 1.075v (BIOS)
    Loadline Calibration : Enabled
    CPU GTL Reference : 0.63x
    North Bridge GTL Reference : 0.67x
    DDR2 Channel A REF Voltage : Auto
    DDR2 Channel B REF Voltage : Auto
    DDR2 Controller REF Voltage : DDR2_REF
    SB 1.5V Voltage : 1.50v (BIOS)

    NB LED Selection : NB Volt
    SB LED Selection : SB Volt
    CPU LED Selection : CPU Volt
    Voltiminder LED : Enabled

    CPU Spread Spectrum : Disabled
    PCIE Spread Spectrum : Disabled

    Under Advanced
    And CPU Configuration:
    CPU Ratio Setting : 9
    C1E Suppport : Disabled
    CPU TM Function : Enabled
    Vanderpool Technology : Disabled
    Execute Disable Bit : Disabled
    Max CPUID Value Limit : Disabled

    Under Advanced
    And USB Configuration :
    USB Functions: Enabled
    USB 2.0 Controller : Enabled
    USB 2.0 Controller Mode: HiSpeed
    BIOS EHCI Hand-off : Enabled
    Port 64/60 Emulation : Disabled
    Legacy USB Support : Enabled
    Last edited by Talonman; 03-02-2008 at 05:37 AM.
    Asus Maximus SE X38 / Lapped Q6600 G0 @ 3.8GHz (L726B397 stock VID=1.224) / 7 Ultimate x64 /EVGA GTX 295 C=650 S=1512 M=1188 (Graphics)/ EVGA GTX 280 C=756 S=1512 M=1296 (PhysX)/ G.SKILL 8GB (4 x 2GB) SDRAM DDR2 1000 (PC2 8000) / Gateway FPD2485W (1920 x 1200 res) / Toughpower 1,000-Watt modular PSU / SilverStone TJ-09 BW / (2) 150 GB Raptor's RAID-0 / (1) Western Digital Caviar 750 GB / LG GGC-H20L (CD, DVD, HD-DVD, and BlueRay Drive) / WaterKegIII Xtreme / D-TEK FuZion CPU, EVGA Hydro Copper 16 GPU, and EK NB S-MAX Acetal Waterblocks / Enzotech Forged Copper CNB-S1L (South Bridge heat sink)

  2. #2
    Administrator
    Join Date
    Nov 2007
    Location
    Stockton, CA
    Posts
    3,569
    Nice !!

    Getting close to 4.0

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •