**Official DFI LanParty UT 790FX-M2R Review/Overclock/Guide Thread**

[Brother Esau]

You can find the Tmod/Loggan cd here.

Also have you tried flashing with no command line switches?

Tmod

Hey, Terry whats up my brother? The mighty Tmod enters the building Whats shaking with you Terry you still running the DYI-STREET Site?

[Tmod]

Hey, Terry whats up my brother? The mighty Tmod enters the building Whats shaking with you Terry you still running the DYI-STREET Site?

Hey dude long time no talk, Yeah I am still at the street but I can re-assure you I was never running it.

I am just the coder there that puts skin and vBulletin stuff in it's proper place.

So off to the East coast heh, Where about's?

Hope the trip goes smoothly!!

Tmod

[Rammsteiner]

I learned another new thing... lol. Prime in Windows Safe Mode > everything. I BSOD'd a few times at ettings Ive always been stable on, but this time sometimes after 9 hours of Prime it BSOD'd anyway.

But as I never cleaned my HDD from previous mobo I think few things aren't stable software wise. From now on Ill only Prime in Safe Mode.

[Brother Esau]

I learned another new thing... lol. Prime in Windows Safe Mode > everything. I BSOD'd a few times at ettings Ive always been stable on, but this time sometimes after 9 hours of Prime it BSOD'd anyway.

But as I never cleaned my HDD from previous mobo I think few things aren't stable software wise. From now on Ill only Prime in Safe Mode.

Why would you do that? You know you are just asking for problems when you change Motherboards and are too lazy to do a fresh install

[Oliverda]

Has anyone tried the 800MHz memory mode around 250MHz FSB? It always stucks on post code 25.

(1/30/2008 BIOS with Phenom 9500)

[Jaivan]

Has anyone tried the 800MHz memory mode around 250MHz FSB? It always stucks on post code 25.

(1/30/2008 BIOS with Phenom 9500)

I'm running at 255MHz FSB and 800MHz memory.
Have you tried to lower the NB multiplier i'm using x8 instead of the stock x9.

[Rammsteiner]

I'm running at 255MHz FSB and 800MHz memory.
Have you tried to lower the NB multiplier i'm using x8 instead of the stock x9.

Bah, I want +5x NB multie's too.

Anyway, I heard in order to reach higher RAM OC's it 'might' help to increase Vcore over 1.52~1.53V? Is that true? I could test it myself but it's finally running nice now and dont want to go trough the hell of 'forgetting to reset Memset and thus freezing' etc. Just wondering if someone knew more about it?

[Rammsteiner]

[/B]


Why would you do that? You know you are just asking for problems when you change Motherboards and are too lazy to do a fresh install

Wasnt really lazy to re-install, I was more like too lazy to call MS for a new code as I was changing mobo's. But in Windows Safe Mode it worked after all.

@ Oliverda

Well, I always get '25' when ever I get a BSOD which is very most likely RAM related. I simply get rid of it by pulling the power plug, wait for the LEDs to go out and put it back in. If it doesnt work CMOS reset.

If that doesnt work it's most likely you selected too tied timings and/or too high Mhz for the RAM and thus cant stay stable to even get into BIOS, so you'll have to reset CMOS then.

But it's possible, Im running 14x251 and DDR800 fine.

[EDIT] However, now I see you're using a Phenom. Ive no idea whether you forgot a 'Phenom' option in BIOS?

[Iketh]

sorry if this is already common-sense with all boards that are run outside a case, but it's caused me a few headaches since i got this board in december

my cell phone locks up my system every time it does a synch if it's sitting anywhere within 5 feet of the board...

90% of the lock-ups i've had previously was because i placed my phone near my board... all those mysterious lock-ups 5-30 minutes after finishing a successful prime test were from my moto razer

[Iketh]

updated sig... been running this o/c with a much lower cpu voltage