ASUS Maximus Formula SE

[doronav02]

i have to know about the vid of the cpu is it good or bad to have lower.
and if there is way to know wich cpu better for oc?
i have vid-1.2875v q6600 and i cant go up to 4ghz(now i'm with 3900 1.6v 40c ide 74c load)

[ElEctric_EyE]

i have to know about the vid of the cpu is it good or bad to have lower.
and if there is way to know wich cpu better for oc?
i have vid-1.2875v q6600 and i cant go up to 4ghz(now i'm with 3900 1.6v 40c ide 74c load)

Sounds like you've peaked with load temps like that. Most Q6600s I've seen don't go past 4GHz with your typical water cooling. I can get close to 4.1 but just idling. It's not stable.

[doronav02]

Sounds like you've peaked with load temps like that. Most Q6600s I've seen don't go past 4GHz with your typical water cooling. I can get close to 4.1 but just idling. It's not stable.

i was able to ide 4.2 but not stable.
i'm waiting for the next bios,maybe more mhz.
do you know about vid?lower better oc?

[jorgito05]

i have to know about the vid of the cpu is it good or bad to have lower.
and if there is way to know wich cpu better for oc?
i have vid-1.2875v q6600 and i cant go up to 4ghz(now i'm with 3900 1.6v 40c ide 74c load)

Why din't you use the CPU block that came with your cace. When I saw the size of it, I thaught yea this one is nice. My temps are as follows, With the case WC fan control on normal:

Core 0: 34c
Core 1: 35c
Core 2: 33c
Core 3: 34c

[doronav02]

Why din't you use the CPU block that came with your cace. When I saw the size of it, I thaught yea this one is nice. My temps are as follows, With the case WC fan control on normal:

Core 0: 34c
Core 1: 35c
Core 2: 33c
Core 3: 34c

my case without the wc,yours looking nice.
i'l try dry ice or ln2,
by the way did you notice that with the profile you get stable and if you change it and return it's not the same you'l have to play again?

[doronav02]

can i get 500+ with maximus ?
if so, i try vtt,nb,gtl and didnt go even 470+,i see (not here) with 100$ mb
goes 500+
thanks

[loften]

for lapping anything i use a true flat thick piece of glass or metal (checked with a straight edge) then tape some wet dry auto paper on it and go to town. 500,1000,1500,2000. i make sure i keep it clean, no zippers, little granulars in the paper or under it. you will feel them if they are there. i use a straight edge on whatever i am lapping against light to check for flatness. if it has any highs or lows light will shine through..

[ReZ_]

Where is the intel hyperthreading option in the bios??

i remember seeing it in my bios, but now i can't find it!

I'm having audio latency issues with reason 4.0, and i want to toy with HTT to see what it does

thanks

[ChaosAD]

I have the following problem.Prime 95 Small FFt's im am rock stable.But when i run the Blend i always get an error at 47-48 min.And i mean no matter what bios settings i have (PLL volt-NB volt-RAM volt-SB Volt) i always get an error at exactly 47-48 min.Not 46 neither 49.Do u have any ideas what to pay attention at.I have run out of ideas

And by the way i have lowered the mem timings @ 5-5-5-15 an increased Ram volt at 2.1.Still nothing.