**Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread**

[terroristone]

man this is really doing my head in, i came so close o smashing my pc to bits! im still dam angry. i removed my hard drives and fitted my raptors, tried to boot and got the dam C1 error, i mean wft change drives and it C1ś, so far i have another stick of ram in and trying to get windows installed on my raid setup, i cannot find the floppy that came with my board, i don even remember seeing one for that matter, i downloaded the raid flpy.zip drivers and copied them to a disc, windows comes up with his disk cannot be read because it contails an unrecognized file system¨ im so frustrated...any ideaś or links to the right floppy??
Regards Andrew

[terroristone]

i have gotten the floppy all sorted, can anybody shead some light on why i got the C1 error after changing my HDDś ???
Andrew

[turtletrax]

i have gotten the floppy all sorted, can anybody shead some light on why i got the C1 error after changing my HDDś ???
Andrew

I know how frustrating DFI boards can be but there is always the old standby when having issues. The battery removal clear CMOS. There are so many times I have had really strange behavior and done a battery remove and problems gone.

Just the cost of using the bleeding edge boards. I also find that ehen I get really choked at these boards is the perfect time to do a bettery removal. Leave it for a couple hours minimum and come back with a more relaxed attitude. Worked everytime so far

[terroristone]

ok this is where im at, system back to normal specs, windows has installed, after first reboot to continue install i get BSOD, seems nothing i do so far will stop this....any ideaś?? i can believe the problems im having, my old dfi nf4 expert was a dream compaired to this...
Andrew

[luihed]

When you get the C1 error, try this.....

-Turn off and unplug PSU
-move jumper J1 from 1-2 to 2-3 and wait maybe 10 sec..
-move the jumper back to original pos. and turn your system back on....

or

-Turn off and unplug PSU
-clear cmos and the jumper right beside it, then take off the batt.; wait a few
-replace batt and both jumpers and thy to boot...

Hope this helps cos thats the only hting thats getting me going these days using my QX9650....

I swear running DFI boards is like having a really hot girlfriend thats a total b!tch....

[Brother Esau]

When you get the C1 error, try this.....

-Turn off and unplug PSU
-move jumper J1 from 1-2 to 2-3 and wait maybe 10 sec..
-move the jumper back to original pos. and turn your system back on....

or

-Turn off and unplug PSU
-clear cmos and the jumper right beside it, then take off the batt.; wait a few
-replace batt and both jumpers and thy to boot...

Hope this helps cos thats the only hting thats getting me going these days using my QX9650....

I swear running DFI boards is like having a really hot girlfriend thats a total b!tch....

I Love it

[terroristone]

I swear running DFI boards is like having a really hot girlfriend thats a total b!tch....

so dam true man.

The C1 error has gone, im doing another install using a different raid driver to see if thats whats causing the BSOD.
Thanks for all the help guys, i need to settle down sometimes and think a little more logitical.
Andrew

confirmed : im an idiot..hehehe the other raid driver worked...seems all good so far..

[luihed]

********QX9650 or Quad Owners, Please respond******

I recently got a QX9650 and ive been having some trouble booting after a failed overclock... I just noticed that my cpuVTT was undervolting like crazy when using the QX, my E6600 on the other hand is OK

QX9650- set at bios=1.6v actual=1.43v
E6600- set at bios=1.6v actual=1.58v

from clear cmos... ( default 1.2v)

QX9650= 1.07v
E6600= 1.2v

Actual voltage taken straight from mobo by multimeter, same figure I get from smart guardian...

[turtletrax]

ok this is where im at, system back to normal specs, windows has installed, after first reboot to continue install i get BSOD, seems nothing i do so far will stop this....any ideaś?? i can believe the problems im having, my old dfi nf4 expert was a dream compaired to this...
Andrew

Have you done the Battery Removal for hours? Perhaps overnight as well? I have had it where I set something too agressive in the BIOS and it screwed the CMOS just enough to hoop me. I would go back to known settings and it would still be borked. I had to clear CMOS for hours at a time to get back to normal, but after that all is back to normal.

Hello Gentleman, Merry Christmas to all I miss the thread and all you guys allot!

Getting quite lonely in AMD Land

And a Merry Christmas to you too

And as far as you missing the T2R forum, by the sounds of anything relevant on the AMD side of the camp, you will most likely be back before long