Asus P5K "Vanilla" vmods

[Learn]

Very nice OC
It worked for you too, perfect

[Nosfer@tu]

NEED Ln2 or Cascade

I pulled 4800 on dryice with all 4 cores enabled andSuperpi stable.
4900 With 2 cores and superpi stable.

The board ROCKS.

[Achill3uS]

I've found in an other forum the P5K PLL vmod, and made it yesterday. Works fine, and helps much if you think you find an fsb wall

[Gamer]

Can a 20k vr be used to do a vcoremod ?

[wittekakker]

yes, it will overvolt your CPU in most cases though.

[h3x0r_1984]

Does the VPLL mod give u more BIOS voltage options?Or do u have to set it manually using the VR added?
In the case of Vdroop mod,will a 22k VR set to 15K do the trick?

[Nosfer@tu]

Yes it will, I mean the 15 K will do.
But make sure it is a multi turn so you can adjust it perfect

No it dosent give more options. You can lower resistance and thus increase the Vpll voltage

[h3x0r_1984]

I just made my mod teamjapan style(just slammed in a 14K resistance set on a the 22k VR i used),and the mod,along with Digital Multi measurements looks like this:

[MaSell]

Have fun with your fsb wall

[h3x0r_1984]

My FSB wall is over 400..at about 410...something like that. So my rig benches very fine at 3600-3700 cpu,wich is more than enough.But thank u for the mod.

[metro.cl]

anyone knows where i can find P5K3 Deluxe vmods?

[pippo369]

anyone knows where i can find P5K3 Deluxe vmods?

Is the same of P5K de Luxe

[Eldonko]

What kind of droop are you guys getting on Vanilla with droop mod (pencil or trimpot) with a quad?

[oohms]

Mods for:
vdroop
vcore
vcore OVP
vdimm
vmch
vgltref
vpll

Reading points for:
vcore
vdimm
vmch
vpll
vgtlref (not in pic, will add soon)
fsbvtt
vcpupll

Only using info found in this thread

[T_M]

Nice cabling dude

[dinos22]

COOOOOOOOOOOOOOOOOOOOOOOL

[Jasy]

Nice and clean

[Eldonko]

Yeah GJ. If only ASUS made the boards like that in the first place lol.

[Boogerlad]

hello, new to volt modding. I just got a couple questions. when using a vr in these mods, you hook it up to the point mentioned in the pic, and then to ground, and when doing vdroop mods, you just do + to - on the resistor via a pencil, and when measuring vcore or vdimm, etc, you do?

[Eldonko]

That's correct. For measuring just check from the read points posted with DMM, red to read pt, black to ground.

[metro.cl]

Have fun with your fsb wall

Do you have any reference values for the mod?

[MaSell]

Unfortunatly not. I just pencil resistor, got 2v vpll when I set 1.7 in bios and is ok

[spectrum48]

question: how far can i go with the vcpu pll on air without killing the cpu?

so far i've tried up to 1.95v pll, maxxing out @ 562mhz fsb (e6300)

and btw thanks to the people who posted the mods, currently i got vfsb, vcpu pll, vdroop (pencil) and added a couple of caps

pic1 pic2

[metro.cl]

Unfortunatly not. I just pencil resistor, got 2v vpll when I set 1.7 in bios and is ok

Could you measure the resistece on the resistor? 2.0v when set 1.7v sounds good.

question: how far can i go with the vcpu pll on air without killing the cpu?

so far i've tried up to 1.95v pll, maxxing out @ 562mhz fsb (e6300)

and btw thanks to the people who posted the mods, currently i got vfsb, vcpu pll, vdroop (pencil) and added a couple of caps

pic1 pic2

Could you please link me to the pencil vdrop mod, i've been looking a lot for this pencil mods

[spectrum48]

Could you please link me to the pencil vdrop mod, i've been looking a lot for this pencil mods

sure, it's posted here