E6850+Dimastech SS1HP:Only a warming up run!82.2k 3d'01 ecc

**nachthymnen** · 11-06-2007, 11:37 AM

Arrived today ma Dimastech EVO BEAST 1HP SS

Tks to Andrea "Dimas"

Immediatly put on my E6850.
Don't have control the contact between Evap and CPU

Cpu @ 3.6Ghz with 1,32V

"THE BEAST":

SPI @ 4596Mhz=10.953(1,6V & 1,75V-PLL)

PIFAST @ 4560mhz(1,62V & 1,75V-PLL)

Aquamark3 @ 4512Mhz=250.565 (1,6V & 1,75V-PLL)

3dMark'01 @ 4452Mhz=82.290 (1,6V & 1,75V-PLL)

This is just a warming up run, vga without v-mods and not pushed high... tomorrow I re-run all benchs with door and windows opened

**metro.cl** · 11-06-2007, 12:11 PM

Nice results but you have lots of room to improove on the CPU, with similar temps (yours a bit colder) i was able to bench easily at 4.8GHz and Super Pi at 4950MHz with a E6850.

**nachthymnen** · 11-06-2007, 12:51 PM

Originally Posted by metro.cl

Nice results but you have lots of room to improove on the CPU, with similar temps (yours a bit colder) i was able to bench easily at 4.8GHz and Super Pi at 4950MHz with a E6850.

Yes, it's only a very fast test

Today not many time to play

**Oliver** · 11-06-2007, 01:22 PM

Looks really good

.

Keep pushing it.

**splmann** · 11-06-2007, 01:44 PM

Bravo !!! Looks good !!!

Regards

SPLMANN

**nachthymnen** · 11-06-2007, 08:15 PM

Tks guys

I must take confidence again with cold temps bench

More than 1 years ago I've sell my Cascade

Today I run all 3d marks

Just a small '01 test @ 4.5Ghz in LL give me 1104Fps

**andre X_X** · 11-06-2007, 09:12 PM

looks good.... 82k 3d01 with cpu only 4.4ghz looks promising

i got same scores with 2900XT (901/1083) on E6600 at 4.75ghz.

**nachthymnen** · 11-07-2007, 08:49 AM

Originally Posted by andre X_X

looks good.... 82k 3d01 with cpu only 4.4ghz looks promising

i got same scores with 2900XT (901/1083) on E6600 at 4.75ghz.

TKS Andre

Some up with 1,6V cpu, still testing, tomorrow mor V-core

3d'05 @ 4512Mhz=25.803

http://service.futuremark.com/compare?3dm05=3651281

3d'01 @ 4500mhz=83025(sorry for the screen without the partials

, also I can't up the score in the ORB

)

I remember: 870.5fps N/432.2fps LH/751.4fps DH/317.0fps CH/

Aquamark 3 @ 4536Mhz=251.327

And I close with a fun SPI @ 4.8Ghz

I've problem with the RAM 1:1, can't set PL @ 6

No eram, no max mem, no real time and don't close Explorer

Just a cpu test:

SPI @ 4800mhz=10.641

Tomorrow I'll push the cpu with 1,66V.
I like to increase mhz a little bit per day

**nachthymnen** · 11-07-2007, 10:09 AM

3 other fast test:

Aquamark3 @ 4608mhz=253.616(PCI @ 104)

Pifast @ 4656Mhz=20.08

Lobby low @ 4608Mhz=1129.9fps

So cold

**MadMax75** · 11-07-2007, 01:18 PM

Complimenti anche di qua ! ottimi score , vedrai che migliori qualcosina

**Enoc** · 11-07-2007, 06:40 PM

nice runs Nacht

what temps do you get on load with that SS? looks like similar to dry ice temps...

**dinos22** · 11-07-2007, 06:47 PM

that's a great cooler

if i had a better mix of gasses and load tuning i would probably have similar temps but i've tested a few CPUs and my E6850 easily benches 32M SuperPi at 4.9Ghz

(FSB WALL) and E6750 easy 4850Mhz before it hits a FSB wall.....but i am trying to get some time and bench this E6750 past 600MHz FSB 3D....love the chip

so i guess what i'm saying is that your CPUs should be easily there too

since you are about 10C cooler

and similar sort of compressor and all heh

oh for reference i ran wPrime 1024M at 4840Mhz on E6750 with 1.69v and had -45C on evap around 20-21C ambient and my CPU core temp was at -14C

**nachthymnen** · 11-08-2007, 07:26 AM

tks guys

Bad news, fsbwall around 536/537 I think

2 fast up:

PiFast @ 4704Mhz=19.94

SPI 1M @ 4812Mhz=10.594

http://valid.x86-secret.com/show_oc.php?id=265341

Tomorrow some 3d marks

ADD 09/11:
Aquamark3=254.000 (Just a test)

3d Mark'05 @ 4632Mhz=26.214 (PCI @ 105mhz

)

http://service.futuremark.com/compare?3dm05=3657435

3d Mark'01 @ 4632Mhz=84.498 (Bad GT1)

**nachthymnen** · 11-09-2007, 10:09 AM

2 fast test @ '03 and '06, vga with low freq.

18.5° room

3d'03 @ 4596mhz=53.652

3d'06 @ 4596Mhz=15.974

The thermomether sensor is not installed well but here is a shot during '06 with cpu @ 4596mhz at 1,72V and 19° room temp(phase warking from around an hour)

**nachthymnen** · 11-10-2007, 12:59 AM

Lost over 30 minutes only for run CL in 3d'01

3 little UP:

Aquamark3=255.746

3d'01=84992

3d'03=54124

http://service.futuremark.com/compare?2k3=5598121

**G H Z** · 11-10-2007, 01:20 AM

Thats a nice cooler and setup nachty, if you encounter FSB limits try loosening PL levels. Your '01 & AQ3's look really good

**nachthymnen** · 11-10-2007, 01:27 AM

Originally Posted by G H Z

Thats a nice cooler and setup nachty, if you encounter FSB limits try loosening PL levels. Your '01 & AQ3's look really good

Tks GHZ

The cooler is very strong, and I've not control the contact between evap and cpu

Till now I'm not able to close PI 1M @ 536x9

I've try also with ram 5-5-5-15 but probably with PL7

I'll try with PL @ 8

Well, AM3 and '01 it's not bad

Now my '01 sequence is:
LL/N/CH/DH/LH/DL/CL with 4.8LB each test
Starting with LL give me a boost of around 60Fps

When I run LL after LH I can get only 1070/1075fps
I lost 3/4fps in CH but it's nuts

The problem is the PCI @ only 105mhz

I lost around 30FPS in Nature

Can't wait for the v-modded Ultra's return next week

**nachthymnen** · 11-10-2007, 02:33 AM

With PL @ 8 I've close SPI @ 536x9 but very very unstable

Just 1 time and no able to repeat now

2 other small UP

PiFast @ 4728Mhz=19.86

3d'06 @ 4620mhz=16.096

http://service.futuremark.com/compare?3dm06=3710367

**nachthymnen** · 11-10-2007, 06:14 AM

Tks GHZ

PL @ 9

http://valid.x86-secret.com/show_oc.php?id=266225

@ 4872mhz freeze @ 10"

Try for 3 times but nothing.
Well, not bad at all.

**nachthymnen** · 11-11-2007, 02:13 AM

PL @ 10

SPI @ 4896Mhz=10.438(no ERAM, no realtime)

http://valid.x86-secret.com/show_oc.php?id=266649

@ 4908Mhz freeze after 7 seconds, but I'll try again soon

Tks again GHZ!

SPI 2M @ 4848Mhz=25.859

SPI 4M @ 4788Mhz=59.875

First run in 32M, I'm searching for a stable setup for the ram...

SPI 32M @ 4596Mhz=10'54".250

**nachthymnen** · 11-12-2007, 02:03 AM

No more 3d bench this week

Vga has been sent to my friend for the v-gpu mod

Ram testing in 32M...

SPI 32M @ 4620mhz=10'48".469

**nachthymnen** · 11-18-2007, 09:41 AM

Tomorrow my friend ship back to me my Ultra v-core modded

This is a fast test done by him:

Air Temp=23,3°/ Water Temp=27,1° ultra @ 750/1190(gpu at 1,45v) Q6600G0 4Giga

I'll put it under iced water @ 1,55V next week

Hope to reach 800mhz core

**Dynasty** · 11-18-2007, 10:13 AM

very nice 3d runs

, single 8800 ultra still looking strong.....

what forcewares u running with.......

**nachthymnen** · 11-18-2007, 11:00 AM

Originally Posted by Dynasty

very nice 3d runs

, single 8800 ultra still looking strong.....

what forcewares u running with.......

Tks friend

Can't wait for test it under cold water

I'll run with the 169 forceware driver

**nachthymnen** · 11-20-2007, 11:47 AM

The Ultra is back

And tomorrow I'll receive this chip from my friend that has made 2 fast test under day-use liquid cooling setup before to send it to me...

Pi @ 4664Mhz 1,568V

3d'05 @ 4500mhz 1,58V

Tomorrow the initials aircooled test and saturday on my -65°C SS

Thread: E6850+Dimastech SS1HP:Only a warming up run!82.2k 3d'01 ecc

Thread Tools

Search Thread

Rate This Thread

Display

E6850+Dimastech SS1HP:Only a warming up run!82.2k 3d'01 ecc

Bookmarks

Bookmarks

Posting Permissions