New C2D Max and SPI 1M WR by NewBeetle (Team Japan)

[eva2000]

NewBeetle... did you play with DFI board's GTL+ ref volts and clk fine delay values those 2 can either allow your fsb to go higher or in worse case on bad settings prevent your system from booting even at stock cpu speeds (particularly clk fine delay it's individual memory/pcb dependent as to it's values and can change values needed depending on memory divider and timings used).

[Oliver]

I hear DAKARA's P-35 T2R has also cold bug...
On gas cooling, His board worked at only FSB555, but his chip can work at FSB 630.....

DEWA DEWA ～
NewBeetle

Thats really sad .
The 2nd. E6850 looks very good .

Keep pushing it.

DEWA DEWA .

[NewBeetle]

NewBeetle-san
here is the other thread test under LN2 actually
http://www.xtremesystems.org/forums/...d.php?t=157085

NewBeetle... did you play with DFI board's GTL+ ref volts and clk fine delay values those 2 can either allow your fsb to go higher or in worse case on bad settings prevent your system from booting even at stock cpu speeds (particularly clk fine delay it's individual memory/pcb dependent as to it's values and can change values needed depending on memory divider and timings used).

Thats really sad .
The 2nd. E6850 looks very good .
Keep pushing it.
DEWA DEWA .

Hi, dinos22-san, eva2000-san, Oliver-san.

The cause was not cold bug but memory & sockets' loose connection... .
I'm very sorry to make you disappointed.

Now I have little good news.

MAX FSB (CPU-Z)


MAX FSB (SPI-1M)


MAX Clock(SPI-1M)


Setup (MAX FSB)
M/B：DFI LP UT P35-T2R Rev:A1 (U733302***/LP35D810)
M/B Bed：「V-TEC ARC Bed Rev.3.3」
NB cooling：Normal-sink
SB cooling：Normal-sink
CPU：Intel Core2 E6700(L633A549#7)
CPU cooling：MaxxNEO + LN2 / temp：-125C
Memory：Team Xtreem PC2-8500 C4 1GBx2 4-4-4-8
VGA：ATI XPERT 98 PCI 8MB
HDD：Western Digital WD360ADFD
Power Supply：OCZ PowerStream 520W
Vcore：1.500V(Setting)
Vio：3.47V(Smart Guardian)
Vdimm：2.65V(Smart Guardian)
OS：Windows Server 2003

CPU Feature
- Thermal Management Control: Disabled
- PPM(EIST) Mode: Disabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Disabled
- Execute Disable Bit: Enabled
- Virtualization Technology: Disabled
- Core Multi-Processing: Enabled

DRAM Timing
- Enhance Data transmitting: AUTO
- Enhance Addressing: AUTO
- Channel 1 CLK fine delay: Current(14)
- Channel 2 CLK fine delay: Current(0)
-
- CAS Latency Time (tCL):4
- RAS# to CAS# Delay (tRCD):4
- RAS# Precharge (tRP):4
- Precharge Delay (tRAS):9
- others "AUTO"

Exist Setup Shutdown: Mode 2
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock: Enabled
CPU Clock Ratio:6
- Target CPU Clock:3480MHｚ
CPU Clock:580MHｚ
Boot Up Clock:Auto
DRAM Speed:333/667
- Target DRAM Speed:ddr2 1167
PCIE Clock: 100MHz

Voltage Settings
- CPU VID Control:1.50000V
- CPU VID Special Add:Auto
- DRAM Voltage Control:2.600V
- SB 1.05V Voltage:1.217V
- SB Core/CPU PLL Voltage:1.95V
- NB Core Voltage:1.77V
- CPU VTT Voltage:1.60V
- Vcore Droop Control: Disabled
- Clockgen Voltage Control: 3.85v
- GTL+ Buffers Strength: Strong
- Host Slew Rate: Weak
- GTL REF Voltage Control: Disable

I think DFI P35-T2R is a very good mobo because this board is no mod at all.
But I have two problems.
1. DFI's PI Time is bit slower than ASUS's. (maybe because of my poor tweaking )
2. No Vcore mod. (I gain only 1.82V though I set Vcore in the maximum)

DEWA DEWA ～
NewBeetle

[dinos22]

sooo you can't mod vcore on that digital PWM

have you assigned special value in bios for extra vcore

[NewBeetle]

sooo you can't mod vcore on that digital PWM

have you assigned special value in bios for extra vcore

I assigned special value in bios for extra vcore:130%.
But Vcore showed only 1.82V...

[dinos22]

I assigned special value in bios for extra vcore:130%.
But Vcore showed only 1.82V...

that's bad news

especially if you cannot mod vcore on digital PWM

[BeardyMan]

Hehe poor newbeetle he wants that +1.9V very hard

Nice results anyway youre a master tweaker

[Oliver]

Thats really good to hear champ.

But sad about the vcore.

Any results yet with your E6850s now that the board is running.

Keep pushing it.