**Official ABIT IP-35 Pro Review/Overclock/Guide Thread**

[Dami3n]

Thanks Ace , i try to put some air in that zone or remove the heatsink an put some fresh as5 to improve the contact.
Ace, im 400x8 now at stock board volts, whats your mobo volts to 450 fsb?

[MADMAX22]

Make sure the stock heatsinc is actually touching the pwms. I took mine off and it was only touching about a third of them. I cut up a HDD cooler and put that on there and I see 36c idle and 38c to 40c load at 1.55vcore. With higher vcore it goes up from there where I ahve scene 53c before.

[Ace-a-Rue]

my vcore is between 1.53-1.55...

my room temp is 77F....AC

[Dami3n]

36º idle and 40º load, this temps are much better. I don´t understand why abit don´t improve this little things. With a good contact heat-pipes this board are very cool compare with other p35´s.

Ace, 1,55v mch to 450?

[Ace-a-Rue]

Ace, 1,55v mch to 450?

no!...1.44v to run 540 Mhz memory speed

EDIT:...2.14v for Vdimm.

[Ace-a-Rue]

Make sure the stock heatsinc is actually touching the pwms. I took mine off and it was only touching about a third of them. I cut up a HDD cooler and put that on there and I see 36c idle and 38c to 40c load at 1.55vcore. With higher vcore it goes up from there where I ahve scene 53c before.

i tend to avoid doing that in the beginning just in case i have to RMA it back for a replacement...the next time i take the board out of the case, i will consider doing that...waiting on the next "big" air cooler to come along!

[Dami3n]

no!...1.44v to run 540 Mhz memory speed

EDIT:...2.14v for Vdimm.

thanks Ace.

[MADMAX22]

i tend to avoid doing that in the beginning just in case i have to RMA it back for a replacement...the next time i take the board out of the case, i will consider doing that...waiting on the next "big" air cooler to come along!

Well this one I set up the phase on it before I even fired it up so I was hoping for the best. I kept the stock cooler intact so I could put it back on but I had a extreme spirit II that I put on the NB and modified my cooler for the pwm. Luckily it works like a charm. Great ocing mobo, cant wait to get a cpu that doesnt have a fsb wall at 540mhz to see how high I can get the fsb.

[TASOS]

Got very strange problems when i try to open Uguru.
Installed my IP35 Pro yesterday and a new HD 2900XT. Today i updated bios to b04. Did a run in 3dmark2001 and got 47900p with cpu and gpu at stock.
Using the latest ATI driver to. What can be my problem u think ?

My system:
Abit IP35 Pro
E6600
Asus HD 2900XT
Xtreem PC6400 2gig
Xp Pro

Hope someone can help me

Look at the pic and u know what i mean ^^

Change the default uguru skin appearance ... save the setting and reboot.

Tell me if it worked.

[ante_ante]

Change the default uguru skin appearance ... save the setting and reboot.

Tell me if it worked.

Yes it´s worked. But i can´t get my hand on the OC section

[Ace-a-Rue]

have you tried to uninstall and then re-install Uguru

[alpha0ne]

What are ppl using to take a screen shot of uGuru ??

I have tried irfanview which works for everything except uGuru ????

[strange|ife]

What are ppl using to take a screen shot of uGuru ??

I have tried irfanview which works for everything except uGuru ????

try out MWsnap 3, its freeware. Its old as the hills, but ive always used it, works fine

[Ace-a-Rue]

What are ppl using to take a screen shot of uGuru ??

I have tried irfanview which works for everything except uGuru ????

just hit "Alt" and ""Print Scrn" keys at the same time and then open MS "paint" prog to paste it into the blank screen...save it as a jpeg or gif..that's it!

[furballi]

No need for ALT. Just PrtScn, then open PAINT and EDIT/PASTE...FILE/SAVE. I also enjoy MWSnap...very light application. Works with all versions of windows.

[Ace-a-Rue]

No need for ALT. Just PrtScn, then open PAINT and EDIT/PASTE...FILE/SAVE. I also enjoy MWSnap...very light application. Works with all versions of windows.

that is not the best way since you capture "everything" on the screen...if use "alt" along with the other key, you capture only the highlighted window or prog that is opened.

[Hazzan]

@Ace-a-Rue & Turbodream : maybe you can try this.....

set lower tranparency setting on UGURU and restart.....I try this worked and still Ok...... I use Ati Card



and when I Use Oc with Uguru and set PCI E 107 worked normaly.....no problem

[furballi]

@Ace-a-Rue & Turbodream : maybe you can try this.....

set lower tranparency setting on UGURU and restart.....I try this worked and still Ok...... I use Ati Card



and when I Use Oc with Uguru and set PCI E 107 worked normaly.....no problem

You must be pumping north of 1.5V with 3.62GHz. What's your peak Orthos/TAT/S&M temp? Do you have an L2 revision chip with 100C Tjunction?

My E4300 is semi-stable at 3.6GHz with 1.505Vcore and Big Typhoon/120 x 38mm Panaflo medium speed. Semi because I don't dare run TAT during the summer heat...80C within 30 seconds of test. Yes, the heat spreader has been lapped (top and bottom). I gained about 8C after re-mounting the heat spreader because of poor contact between it and the CPU core.

[alpha0ne]

just hit "Alt" and ""Print Scrn" keys at the same time and then open MS "paint" prog to paste it into the blank screen...save it as a jpeg or gif..that's it!

Ar thanks for that, its been soooo many years since I used alt Prt Scrn I had forgotten all about it

[Hazzan]

@furballi : I dont tell about OC performance but Screen UGURU on ATI Card

[ante_ante]

My Uguru works now, changed skin so now i can OC again

[Curryinahurry]

Serious question: I plan on getting q6600 and ds3r and I've heard good things about its OC abilities. Since I dont need SLI, should I stick with the p35-ds3r or get the IP35-pro?? Its seems to me both boards are pulling off similar FSB.

[Ace-a-Rue]

does giga have something similar to Abit's Uguru?

[Curryinahurry]

What's so special about Uguru

[Ace-a-Rue]

you change FSB, PCIe bus speed and all voltages that count for overclocking right from windows...the only thing you can't do is change memory straps and multipliers...memory straps need a re-boot to accomplish a change in configuration!

this is what you can change from windows: