Retail E6850 @4GB

[clone38]

http://valid.x86-secret.com/show_oc?id=217674

E6850 @ 4GHZ

Product Code:- SLA9U "G0 Stepping"
Batch No:- L720A696
Pack Date:- 07/02/07

Motherboard EVGA 680i( P29 Bios)
4GB OCZ 9200 Flex ram (watercooled)

Cooling Loop 1
120.3 Thermochill rad with 3X SH Yate Loon`s on low
Pump D5
1/2" Black Tygon
Ram share`s the loop with a 8800Ultra Superclocked via Swiftech F barb`s.

Loop 2
120.3 Thermochill rad with 3X SH Yate Loon`s on low
Pump D5
1/2" Black Tygon
Cpu block (D-TEK FuZion ) /Northbridge(EK 680i) & southbridge(EK 1.1 nForce 4).


Cpu core volt 1.5v
Ram 2.1v

[antonfrompresto]

Surely you mean at 4 GHz not 4 GB.

[Envydia007]

nice temps @ full load.

[Peepaw]

Very nice.

[STaRGaZeR]

F*cking impressive. And the best of G0 stepping is that it´s still 65nm, can´t wait for 45nm Wolfdales and Yorkfields.

[Envydia007]

OP, can you show a 3dmarks test with your set up?

[erwinz]

http://valid.x86-secret.com/show_oc?id=217674

E6850 @ 4GB

Product Code:- SLA9U "G0 Stepping"
Batch No:- L720A696
Pack Date:- 07/02/07

Motherboard EVGA 680i( P29 Bios)
4GB OCZ 9200 Flex ram (watercooled)

Cooling
120.3 Thermochill rad with 3X SH Yate Loon`s on low
Pump D5
1/2" Black Tygon
Ram share`s the loop with a 8800Ultra Superclocked via Swiftech F barb`s.

Cpu core volt 1.5v
Ram 2.1v

very nice.. now we will be seeing 4 GHz.. 24/7 setup using water cooling or good air cooling..

[largon]

Nice.

nice temps @ full load.

G0 temp readings are off by ~15ºC

[clone38]

Ment to say ghz :P

3DMark test will be done shortly as im still testing.

[erwinz]

Ment to say ghz :P

3DMark test will be done shortly as im still testing.

maybe your testing if it can do 4GHz..

hehehe but I think your not using the full potential of your memory module and the async capability of 680i motherboards..

[clone38]

Cant get me head around ram as it drive`s me crazy .

[AndyM]

Congrats! 1st 4Ghz Orthos stable I've seen with no ape voltages or superpi only stability. Now to make a decision on retiring my 6600 or not, lol.

[adamsleath]

well; im following your lead.

i decided to try 1.5v core.

and i seem to be very stable at 445x9
dr0ops down to 1.45 during orthos.


i checked my bios temp and it says 35C @ 1.5v (asus probe) 1.47v bios
tat says 22C and ctemp says 19C (lol) - all idle temps.

...and asus probe gives yet another reading (lolx2)
looking at probe at max temp orthos it is 45c (which could mean anything) but nuthing alarming tempwise.

using my probing finger:
the nb is slightly warm and the tuniq base is barely luke warm
my ambient is 20C

orthos still running...i'll let it get to 20 minutes...or so.

if it was a summers day at about 28C i suppose i wood be seeing/feeling some heat from the tuniq.

[RPGWiZaRD]

How do you get 20C ambient in australia? I mean currently I have 27C room temp here. That's one reason I also think it might be wiser for me to choose one of these duals over quad cuz the quad temps will kill the chip during summer here as room temp is always between 25 - 28C during summer in this house, my neighbour on the other hand only has like 20C. :s

[erwinz]

Cant get me head around ram as it drive`s me crazy .

you can do it man..

your module can do ddr2 1100 cas 4 easy.. I guess aiming for ddr2 1000 cas 4 ist..

[adamsleath]

How do you get 20C ambient in australia? I mean currently I have 27C room temp here. That's one reason I also think it might be wiser for me to choose one of these duals over quad cuz the quad temps will kill the chip during summer here as room temp is always between 25 - 28C during summer in this house, my neighbour on the other hand only has like 20C. :s

it is the middle of our winter here
summer inside gets to about 28c...then i put the a/c on.

it is 16-18c in the mornings (brrr cold)

[Brother Esau]

@adamsleath....You're from Brisbane? My mom is from Brisbane and Dad is from Aukland. Been thinking of moving to Australia past few years!

Back on topic.....I got the Q6600 over the E6850 and am hoping that the temps are good with this new G0 Stepping with the mosefts being so close on this board. we will see soon enough!

[revogamer]

it is the middle of our winter here
summer inside gets to about 28c...then i put the a/c on.

it is 16-18c in the mornings (brrr cold)

it gets to 0c in the morning here, and -10 around my country

[michaLcoughliN]

4ghz mmmmm.. try for higher!!

[bithkits]

Congrats! I cant wait for these to become available!

[hecktic]

thats nice but i must ask, would you use 1.5v 24/7 ??

[adamsleath]

@adamsleath....You're from Brisbane? My mom is from Brisbane and Dad is from Aukland. Been thinking of moving to Australia past few years!

Back on topic.....I got the Q6600 over the E6850 and am hoping that the temps are good with this new G0 Stepping with the mosefts being so close on this board. we will see soon enough!

g'day brother; i got some cousins in otrahonga, NZ(i know that isnt how you spell it...)
Aussie is a bit drought ridden at the moment...

i think you'd prefer NZ to Brisvegas ...not that you arent welcome

[XtremeTiramisu]

thats nice but i must ask, would you use 1.5v 24/7 ??

If it's 1.5v @ BIOS set and 1.47v windows and 1.46v under load, I think it's still within the absolute safe 24/7 boundary. If it's 1.5v under load, that would be a bit too much for 24/7. However temp matters more as I think none of us will likely to keep the CPU long enough before the detereotion started to take a hit in performance after years..

[adamsleath]

i havent encountered any glitches yet.
playing my usual bf2142 and medieval2...
did 3d06 np

3.6GHz needs 1.4/1.35
3.8 i set at 1.47/1.42
and dats all folks.
im not pushing it further than 4gig, although im sure it would go higher with riddikilus v's.

[billdavis]

that is good

lets see how high you can go