!UPDATE! abit AW9D-Max (retail) arrived

[JokerCPoC]

http://www.xtremesystems.org/forums/...d.php?t=132047

http://www.xtremesystems.org/forums/...d.php?t=131378

you're asking a 50watt tec to move 200watts of heat, with a low heat processor that cooler may work well, but as you scale in heat output it cannot keep up, especially kents... I'm trying to help you not possibly burn your processor, and moreso possibly stop your cpu from throttling. 6000 seti pts a week is good but consider my kent put out 3k - 4k pts/day @ 60C in coretemp

Well according to the front panel(Which is hardware and Not Software, I know the difference) of the Vigor Monsoon II the cold plate is reading 35C right now, Of course that is cause of the uneven load due to a faulty Bios not overclocking the cpu evenly like It should and does on My P5W which is at 45C currently, The P5W is at 36C according to Speedfan 4.31, I won't use Core Temp as It doesn't come close to what the hardware is telling Me. I do pretty good in Seti, I'm 9th out of 169 team members and in 29 days or so I'll get to 8th place, I out produce the top guy right now too, Right now My Rac is 9126.88 and I only have 4 PCs too.



Also as I said earlier I don't get any reboots when the ram is set to 1:1, Just at 2:3 and that is cause the NB heatsink sucks, Otherwise It's completly stable, So the Reboots are not caused by a cpu heat problem which is FUD.

Tweaktown has a review of the Vigor Monsoon II and It's here.
The cpu is a hot Athlon FX-53 of course.

Of course PC Perspectives has an earlier review too(No I don't work there, I just hang out there, As It's a hobby for Me).
http://www.pcper.com/article.php?aid=273&type=expert
The Monsoon II control module also contains an audible alarm that will sound if the temperature drops below 15°C or rises above 70°C.

[775911]

I thought Seti was closed down

[MrDeeds]

Well according to the front panel(Which is hardware and Not Software, I know the difference) of the Vigor Monsoon II the cold plate is reading 35C right now

First, the temps your trusting as golden are being provided by the hardware in question in support of itself. So if it said it was cooling your cpu to -10 degrees, would you believe that also.

Unless your using some sort of probe to provide real temps i wouldnt be so confident in what the monsoon is telling you.

Second, it seems like your have no real interest in believing what you've been told time and time again. The monsoon isnt sufficient in cooling a kent at a high oc let alone a moderate one. You arent the only person to ever make an uninformed purchase but no matter how much denial your in, it doesnt really make the truth any different. Air tecs arent very good.

Third, this discussion has gotten incredibly off topic and turned into a free for all about your general ocing problems aw9d-max related or otherwise. If you wish to continue about the monsoon and feel you have some real documentation and results to back your position then continue that in the air cooling or tec cooling sub-forum.

[fhpchris]

LOL FX53???

Your air tec is garbage. A 50W TEC wont move 200+ watts of heat.

Kunnak runs his QX6700 higher on the stock heatsink than you do on that TEC POS, guess why...

[fastback88]

i can only get around 379 x 9 stable.....however i can get like 410x7 stable...

idk i dont want to think it is my cpu but it might be

1.51vcore
1.75vmch.... 2.1 vdimm....

anything i could be missing

[fhpchris]

i can only get around 379 x 9 stable.....however i can get like 410x7 stable...

idk i dont want to think it is my cpu but it might be

1.51vcore
1.75vmch.... 2.1 vdimm....

anything i could be missing

mch undervolts, 2.0v in bios was ~1.89 real for me.

[ghosty1234]

Is there any chance to make 470-480 @1:1 with a special bios for instance? Just for PI 1M

I mean WITHOUT any kind of mods....

[hipro5]

Is there any chance to make 470-480 @1:1 with a special bios for instance? Just for PI 1M

I mean WITHOUT any kind of mods....

NO......

ONLY with mods you could bench up there....

[TV Addict#2]

will a tuniq 120 fit on the abit AW9D-Max
I found posts with verification,thanks anyhow

[fgw]

mch undervolts, 2.0v in bios was ~1.89 real for me.

can confirm this! what i measured on my aw9d-max:

setting in bios idle before vmch booster load before vmch booster idle after vmch booster load after vmch booster

1,50 1,427 1,421 1,464 1,464
1,55 1,474 1,468 1,511 1,511
1,60 1,524 1,517 1,563 1,563
1,65 1,566 1,559 1,606 1,606
1,70 1,613 1,606 1,655 1,655
1,75 1,661 1,654 1,705 1,705
1,80 1,710 1,702 1,755 1,755
1,85 1,755 1,748 1,802 1,802
1,90 1,806 1,798 1,854 1,854
1,95 1,851 1,843 1,901 1,901
2,00 1,900 1,891 1,951 1,952

you can see clearly the improvement to vmch stability by hipros vmch booster mod! voltage drop is half of the drop as it was without the mod. also, after applying this mod, the drop between idle and load went away completely after installing the mod!

load measurements were done after a few minutes in orthos.

[fastback88]

ok here is main question

could not having enough vmch limit my OC with 9x multi?

7x i can do 410 + but with 9x only 370-380

[fhpchris]

ok here is main question

could not having enough vmch limit my OC with 9x multi?

7x i can do 410 + but with 9x only 370-380

If 7x can do 410, 9x should be able to do 410.

[fgw]

ok here is main question

could not having enough vmch limit my OC with 9x multi?

7x i can do 410 + but with 9x only 370-380

If 7x can do 410, 9x should be able to do 410.

agree to fhpchris!

would suspect vcore be too low ...

[fastback88]

what does this mean as far as read points

http://www.xtremesystems.org/forums/...0&postcount=47

i dont understand

[afireinside]

LOL FX53???

Your air tec is garbage. A 50W TEC wont move 200+ watts of heat.

Kunnak runs his QX6700 higher on the stock heatsink than you do on that TEC POS, guess why...

The silly new air/TEC hybrid coolers are just a big heatpipe sink with a 50w TEC on the top of the baseplate that touches the CPU. The TEC doesn't contact the CPU.

[fgw]

what does this mean as far as read points

http://www.xtremesystems.org/forums/...0&postcount=47

i dont understand

if you are looking for vcore readout points you find them on the back of the board. this coils are soldered to the board at two contact points. the contact point closer to the cpu socket is the place to measure vcore.
as the post says, you can also measure at one of the two contacts of the capacitor. the correct one is easy to find, because one of them is ground and the other one vcore. i personally use the coils, as the soldering points of the coils are pretty big and easy to access.

[nordien]

Dear AW9D-Max users,

I am the proud owner of a Abit AW9D-Max mobo. Rock solid, quality build.

Now there are some issues that may be solved by a new bios (or not)

1. The possibility to run 4:5 DDR1000 @ 4-4-4-15 even @ stock is impossible
2. The possibility to run 1:1 DDR1000 @ 4-4-4-15 even @ stock is impossible
3. The possibility to run 1:1 DDR800 @ 3-3-3-10 even @ stock is impossible
4. The possibility to adjust cpu vtt to 1.4v (very high overclocks possible !)
5. The possibility to adjust all of the termination voltages
6. The ability to go above FSB 438 from the bios
7. I had the program the SPD because of extreme instability with alle Abit bios versions. Tony (OCZ) helped me out

I know that there are serveral 975x mobos wich can do DDR1000 @ 4-4-4-15 and DDR800 @ 3-3-3-10 (Asus P5W DH deluxe/Bad Axe 2). It seems a NB timing issue.

My current setup:

AW9D-Max with active nb cooler
OCZ Ti Alpha PC8000 @ 4-4-4-15. Micron D9GMH
E6600 @ 9*400 3.6 ghz @ 1:1 DDR800 @ 4-3-3-4-20 timings
vMCH 1.75v
vCore 1.4375v
vDimm 2.35v
1066 FSB strap
WD raptor 74 gb
eVGA 8800 GTX @ 640/1500/2100
OCZ GameXtreem 600w
Thermaltake Armor with 25 cm side fan
Tuniq Tower

With these settings the system is 24 hours orthos stable. But i cannot overclock beyond FSB 438, doesnt matter what voltage or strap. The system is completely stable @ 8*438 set in BIOS, but @ 439 no boot ! In Windows the FSB can be set @ 8*450 wich is rock solid.

I hope this info is usefull for you,

[ghosty1234]

1.4 Final is available.
ftp://ftp.abit.com.tw/pub/download/bios/aw9d

[century child]

Noticed fgw's post a bit earlier and flashed immediately using flashmenu. No performance numbers yet (judging from my temps and my many attempts to improve cooling, it looks like I've got a concave 6600 that is in serious need of a good lapping before I'm going to achieve suitable cooling for proper oc'ing) but it didn't bork my box so that's a good sign at least.

[The Viper]

Im interested to see how people feel about this new bios. Im going to be selling this mobo, I loved the speed, but I really needed a board to get my 6600 @4.0 (with no board mods)

[BAR*B*Q]

why do i neet way more vcore then on other boards ?
is vfsb mod helping any ? if i dont had this issue id never give this board away.

[ccokeman]

I find i need less for the same clock speed. 1.475 for 3552 mhz on the aw9d-max vs 1.4825 on the ICFX3200.

[jugeen]

I've updated BIOS 14. Can't boot with 2 RAM modules. Only 1. Downgraded back to 13.

Im interested to see how people feel about this new bios. Im going to be selling this mobo, I loved the speed, but I really needed a board to get my 6600 @4.0 (with no board mods)

[ccokeman]

i also had the same experience. Would not boot with 2 modules on 2 different sets of memeory.

[hawtrawkr]

I find i need less for the same clock speed. 1.475 for 3552 mhz on the aw9d-max vs 1.4825 on the ICFX3200.

im having the same results coming from a p5wdh