new BIOS for DFI infinity 975X

[boshuter]

you need a 40k variable resistor (usually 25 turns), set it to maximum 40k first and work down. First few turns will do nothing, after that it will begin to creep up, you can go to pc health check in bios for a reading, I set up the screen in front of me while I adjust. Or use a dmm and adjust very slowly checking constantly for change, don't overshoot!

I'm a little concerned if you did not know this, only proceed if you're comfortable, otherwise you'll end up with a dead board...

regards
Raja

Raja... do you happen to know what ohms you ended up with at 1.9v ? I don't have any 40k vr's, but a bunch of 20k. If you are ending up with 20k or less at 1.9v I could use one of those, my board will be used for phase and dry ice benching only. Also, do we still need to set all the ram drive strengths with this new bios, or is default ok?

[Raja@ASUS]

put them in series for safety, I did not measure the ohms, it's best to have it higher than required, a quick voltage surge at lower resistance could kill the nb...


regards
Raja

[littleBoy]

I succeed 500fsb!! in 11.03 Bios!!

my mobo is mod state.
vFSB mod, VMCH mod.

Voltage Setting.
=============================================
cpu : 1.6v
NB : 2.0v
Ram : 2.5v
vFsb : 1.55v
=============================================

Test system.
========================================
Cpu : Conroe 6300
Ram : GSkill Hz 2GB 4-4-4-12-15.6 Divide 533
mainbord : DFI 975X/G Rev.A00 (BIos 11.03) Mod
vga : x1800gto 16pipe mod
hdd : raptor 36Gb
Odd : Pioneer 108a
Power : Enermax Liberty 620w
Cooling : cpu(chiller 15dgree) + NB(60mm) + memory(Dual 70mm)
================================================== =======
this shot 480
1M Pi possible



this shot 500
1M Pi Impossible
but I can enjoy web surfing, edit document, during 1 hour!!

[THL]

Link for 11.03 bios?

[erwinz]

@littleBoy

please send me the 11.03 bios.. I just message you my email add.. tnxs

[JWilson]

He's all mixed up. He's siggy and test specs says 11.13 and he probably means 11.15 which is the C15 BIOS...

[erwinz]

got it.. hehehe one impt thing missing.. the board.. ..hope to buy the new revision board..

@littleBoy

thanks.. btw what motherboard revision are you using?? is it the new revision??

[littleBoy]

my mobo's reversion is A00.

I know new reversion new. I expect it.

whether I buy it or don't buy it. I Confused.

[erwinz]

ahh.. if the DFI RD600 is not afar.. I'm going to buy this board again.. hope my friend lend me his board hehehe.. I think not..

@littleBoy

you have an xtreme OC with your board..

[toddm27]

could anyone send me a link to the 1103 bios?

[JWilson]

I see he has now fixed the siggy and test spec to 1103. He's CPU-Z screenie also shows the 11/03/06 BIOS.... So now we need a link for what would be the 97TIDC03.bin.... Anyone?

[shawn1998]

Here is a link to the DFI Streets thread that has a link to it. Question, though. Is the 11.03 supposed to be better than the 11.15 beta on the DFI website? I'm going to be installing this board this afternoon and would like to know what the best beta is to flash to.
http://www.dfi-street.com/forum/show...t=69430&page=3

Shawn

[pumbertot]

Here is a link to the DFI Streets thread that has a link to it. Question, though. Is the 11.03 supposed to be better than the 11.15 beta on the DFI website? I'm going to be installing this board this afternoon and would like to know what the best beta is to flash to.
http://www.dfi-street.com/forum/show...t=69430&page=3

Shawn

I can boot about 10MHz higher with 11.03 over 11.15. still playing with stability but going to vmch mod it this weekend and hopefull fit mcw30 too.

[pumbertot]

do you just pencil in between the 2 empty pads shown for the mod?want to try that now, buy solder iron at weekend.

[erwinz]

do you just pencil in between the 2 empty pads shown for the mod?want to try that now, buy solder iron at weekend.

nice.. post some results..

[elluisro]

ok people.. this is mi first post over here... and I´m giving you the link to a .rar that has... winflash, Bios 730, 913, 1003, 1015

http://rapidshare.com/files/6215954/...sh184.rar.html

password: lan

[RivalNeighbour]

Theres a new beta bios 2006/12/01 now. I checked yesterday at december 7 and it wasnt there at the dfi infinity 975X/G beta site but it's there now.

[erwinz]

link please..

[flyfisher]

http://us.dfi.com.tw/Upload/BIOS/97TIDC01.zip

[m3niac]

Sup Dudes been following this thread since it got started and am happy to report that the last 3 bios are sweet.

This new c01 bios is pretty sweet it adds a memory hole option am not sure what it does so i left it defualt which is enabled.

Right now with 01 bios and previous 11.15 and 11.03 i am able to over clock to 425 on my e6600 I could go into orthos prime and bench it for hours with no problems but as soon as i restart my comp it don't post. It will post @410 after a restart.

My bios settings are.
c1e off
1:1 on the memory
pcix@101
ppm on
325v cpu
1.25v cpu
2.20v mem
1.75v nb

Temps are fine 41 idle 58 load orthos

Why wont it post after a restart.

[erwinz]

cold boot issues.. mm.. i thought this is fix..

[erwinz]

hey Raja..

have you fixed the cold boot issues..

[RivalNeighbour]

DFI Infinity 975X/G 2006/12/01 bios is out of beta now. Heres the US.DFI.COM.TW link. I didnt see a new beta bios yet.

[tifozif1]

DFI Infinity 975X/G 2006/12/01 bios is out of beta now. Heres the US.DFI.COM.TW link. I didnt see a new beta bios yet.

Somebody send me these :
Beta Bios 15-Nov-06
http://us.dfi.com.tw/Upload/BIOS/97TIDC15.exe
http://us.dfi.com.tw/Upload/BIOS/97TIDC15.zip

[ivo0613]

Somebody send me these :
Beta Bios 15-Dec-07
http://us.dfi.com.tw/Upload/BIOS/97TIDC15.exe
http://us.dfi.com.tw/Upload/BIOS/97TIDC15.zip

It's 15-Nov-06, isn't it?