Vision SingleStage by Johann

[johann]

My customer Raju contacted me with something special in mind so this unit I gathered only the best components I could find and got my good friend Dimas to make the case.

Specs:

Compressor: Danfoss NL11F
Condensor: Rifle tubing high performance from Placebo
Refrigerant: R402a
Cappilary: 2.7m 0.031"
Evap: @itor with acrylic kit
Controller: Gfroster XE 1.6

Temps:

Idle: -60c
150w constant: -45c
200w constant: -40c

@itor evap:







DimasTech case with window. It is 590mm deep instead of the usual 490mm to fit under Lain Li PC70 case.



Plexiglass panel with 2 x LCD's. Will measure Condensor in/out temp. The panel will sit behind the Window panel



Power box, contains 15v ac transformer for Gfroster, 5v DC for LCD's and Gfroster power module:





Some shots of unit:











LED's in enclosure

[LowRun]

Looks like it will be another nice one from you

[pazza316]

Nice case and Evap mate!!

Good start!

[Marvin]

looks great, as usual.

[4Qman]

The encolsure is superb.

[Brettbeck]

Great start!

That encolsure would look even better if it had some LEDs in there !

[Raja@ASUS]

yeah we're gonna stick some leds in there, probably red to go with the case...
should be great..

regards
Raja

[mykeos]

me likes that plexi thing

[johann]

Added little plexiglass LCD bracket in 1st post.. It will be mounted behind then window panel and monitor condensor in/out temps

[johann]

1st post updated with pics of virtually done unit. All that needs to be done is LEDs inside enclosure

[Holst]

Looks absolutely superb, and very good performance with it.

Lets hope he can get some great clocks with his new toy

[johann]

Looks absolutely superb, and very good performance with it.

Lets hope he can get some great clocks with his new toy

Thanks Holst, Raju will be bringing his machine over here on Saturday so we can have a bit of playtime and testing on his conroe

[rapty]

Very Clean unit I like the LED's on the side

When can my Unit be sent to be modded by you Johann

[Athens[2004]]

Very Nice the only observation is for those ? aluminum ? screws , i think if u replace them with black screws the whole unit will look's more beautiful

[johann]

Very Clean unit I like the LED's on the side

When can my Unit be sent to be modded by you Johann

PM me what you decided on Rapty and we go from there. The NL11F will proppably be here in a week from now.

Athens, that is a good idea. Raju will make the decision. It is his unit

[pazza316]

Nice unit mate!!

Looks great! and good temps!

[Brettbeck]

Looks great! Are you going to put any LEDs in the enclosure?

[Pete]

Amazing, wish i had my rig back many months on now!

[Raja@ASUS]

I'll be setting up and testing next week, on the Abit Awd9 Max...

After testing the board will go to Johann, he can bench with it further...


The phase unit should be something real special, my E6600 can already hit superpi 1m at 4ghz with 1.54 vcore on water. On phase who knows, ultimatley I trhink I'll hit an fsb wall onthe 975 chipset. I'm awaiting DFI's new board....

regards
Raja

[Unseen]

very nice unit johan. Great work

[johann]

Thanks Unseen

[LukeXE]

Great, great, great Johann ! I like your units, they are powerfull and very clean

[johann]

Realy nice Johann, your customer will be very happy

On a side note, those little LCD thermometers are pretty good value for money. They only go a little off when you get down to low temps, for a condensor theyre grand. The blue backlight behind the large black characters looks damned sexy too!

Top notch work and attention to detail.

Tom

Thanks Tom and Luke! Sure the lcd's are great. They look fine and when not monitoring evap temps or sub zero temp works quite good. I found at around -40c they are about 5-7c off but at above 0 they seem pretty close

[Ssilencer]

Looks excellent!
I want to see it with the leds and mounted over his conroe!

[Messiah Khan]

Don't you dare mount LEDs in it! I want mine to be the first of the see through enclosures with mounted LEDs. Hold it off a few month until Gray gets mine sorted will you please.

Great work by the way. Very neat and tidy.