ASUS P5W DH - Problems + Fixes Thread

**M.Beier** · 08-10-2006, 01:18 AM

One question from meeee

Am I the only one that cant get the board booted by pressing "power-on" on the remote??
Thing is.... I run the gear openair untill Im over with testing it - and thereby has no power-on button, but use a shrewdriver to boot..

**~~Onepagebook~~** · 08-10-2006, 01:22 AM

if you experience post lock up during detecting IDE devices, reset and put some USB storage OR change SATA HD to other socket

**lawrywild** · 08-10-2006, 01:23 AM

Originally Posted by M.Beier

One question from meeee

Am I the only one that cant get the board booted by pressing "power-on" on the remote??
Thing is.... I run the gear openair untill Im over with testing it - and thereby has no power-on button, but use a shrewdriver to boot..

You must enable "Power on after Power off" option in the dh remote control panel in windows

also the receiver must be in ports 3 or 4, the ones that came with a sticker over them.

**M.Beier** · 08-10-2006, 01:30 AM

Originally Posted by lawrywild

You must enable "Power on after Power off" option in the dh remote control panel in windows

also the receiver must be in ports 3 or 4, the ones that came with a sticker over them.

"Power on after power loss" ?

Oh another bad bad issue... - WHen not using CPU fan... That noisebutton, it'll cause system freeze.. :|

**MacClipper** · 08-10-2006, 01:31 AM

New 0903 'S3 resume' bug?

The BIOS fails to re-initialise the JMicron controller properly upon resume from S3 sleep causing the system to freeze periodically as it tries to reload the controller/devices attached to the JMicron.

Event viewer reports controller error or controller not ready error and "devices disappeared from the system without first being prepared for removal" error from Plug and Play Manager.

**lawrywild** · 08-10-2006, 01:44 AM

Originally Posted by M.Beier

"Power on after power loss" ?

Oh another bad bad issue... - WHen not using CPU fan... That noisebutton, it'll cause system freeze.. :|

Yeh, that's the one..

Hmm i don't use a cpu fan connected to the motherboard and the button doesnt freeze anything, it just doesn't do anything..

**M.Beier** · 08-10-2006, 01:47 AM

Originally Posted by lawrywild

Yeh, that's the one..

Hmm i don't use a cpu fan connected to the motherboard and the button doesnt freeze anything, it just doesn't do anything..

Hmm, might be due some disabled functions in bios then

- Pretty much disabled most of HW-monitor section..

But thx =)
I just have to try that power-up stuff

**Primoz78** · 08-10-2006, 01:47 AM

Also when not using CPU fan it always giving you a "CPU fan error" before booting...BIOS 1011

Regards,
Primoz

**Shrekogre** · 08-10-2006, 01:51 AM

Originally Posted by Primoz78

Also when not using CPU fan it always giving you a "CPU fan error" before booting...BIOS 1011

Regards,
Primoz

put cpu fan to ignore on hardware monitor in bios

**lawrywild** · 08-10-2006, 01:55 AM

Originally Posted by Shrekogre

put cpu fan to ignore on hardware monitor in bios

took the words straight out of my mouth

**Mykou** · 08-10-2006, 02:02 AM

@primoz78 and zerocode

update with 375 fsb 1.56 vcore in bios and Vmch 1.65 v unmodded and still air cooling ( others settings the same I gave you ) but still 4:5

I 've not test prime but I guess I have errors

**Primoz78** · 08-10-2006, 02:04 AM

Originally Posted by Shrekogre

put cpu fan to ignore on hardware monitor in bios

Already done it...still the same problem

Regards,
Primoz

**M.Beier** · 08-10-2006, 02:21 AM

Originally Posted by lawrywild

took the words straight out of my mouth

I've just chosen "ignore" in bios, that killed the warning

**M.Beier** · 08-10-2006, 02:22 AM

Originally Posted by Primoz78

Already done it...still the same problem

Regards,
Primoz

THen you must have one of the other fan-control functions enabled..

**maukka** · 08-10-2006, 02:51 AM

Originally Posted by MacClipper

Boot ROM was always left enabled but no go for UDMA on PATA ATAPI devices.

Well, after all, it does state in the manual (page 2-31) that the JMicron IDE connector does not support ATAPI devices at all

**M3kk** · 08-10-2006, 03:11 AM

Originally Posted by OBR

Did you anyone tried MODDED BIOS? With 1.85V NB option? Is it working?

Just flashed now, but... The 1.65 is the max selectable v in bios for NB .. :/

**lawrywild** · 08-10-2006, 03:18 AM

Originally Posted by M3kk

Just flashed now, but... The 1.65 is the max selectable v in bios for NB .. :/

Did you..

Flash with afudos- afudos /i***.rom /pbnc /n

then clear cmos properly, i.e. take out battery, change jumper for 1 min, replace battery and power on?

**Primoz78** · 08-10-2006, 03:20 AM

Originally Posted by M.Beier

THen you must have one of the other fan-control functions enabled..

Have checked it twice...

Will check it again and hope it help cause is annoying...every boot up have to push F1 to go into windows...

Regards,
Primoz

**M3kk** · 08-10-2006, 04:34 AM

Originally Posted by lawrywild

Did you..

Flash with afudos- afudos /i***.rom /pbnc /n

then clear cmos properly, i.e. take out battery, change jumper for 1 min, replace battery and power on?

Tried, but nothing

The max is 1.65v :P

**LUCI5R** · 08-10-2006, 04:49 AM

Originally Posted by MacClipper

@mickey - leave your burners at the Intel controllers for best compatibility, I'm still testing how good the JMIcron is for ATAPI stuff since it is so new esp. to me. btw, if you are adventurous, go crossflash the 111D to 111L for a much better feature set, see CDFreaks for more info.

Thanks! Yeah, i was thinking about leaving the IDE at JMicron and my Burners with Intel Controller for now, untill things are more prominently stable and proven.

I'm gonna look into the crossflash of 111D - 111L at CDFreaks. Adventurous, I Am.

Mickey

**DEVIL_DK** · 08-10-2006, 06:45 AM

another problem if i oc then reboot alle is ok.
if i from windows power down or reboot it
restore to normal sppe and say oc fail LOL
nice i hope nvidia nforce 590 intel ver comes soon.

**catscit** · 08-10-2006, 07:22 AM

this problem:

Keyboard connected via a USB Hub. When system is shut down pressing the keyboard starts the PC. - No fix as of yet, Disabled PS2 Keyboard Startup does nothing to stop this.

i had something alike with my razor copperhead.
unplugging or striking a mousbutton started the pc.
Solved it by flashing from 0701 to 0903 bios.

**MacClipper** · 08-10-2006, 08:11 AM

Originally Posted by maukka

Well, after all, it does state in the manual (page 2-31) that the JMicron IDE connector does not support ATAPI devices at all

Well, it would be nice (& polite) to read this whole thread regarding this issue. Pls read from post at no. 70 onwards before commenting more.

Cheers.

**DjLeco** · 08-10-2006, 08:23 AM

ASUS will be realise sometimes a BUG FREE BIOS for this MB or I will F*** their ingineers...

Is the 7-th bios in an month and STILL a lot of troubles.
I'm thinking to sell that jerk of MB and buy Biostar TForce 965P

**alpha0ne** · 08-10-2006, 08:25 AM

Originally Posted by chefnr1

wich bios is recomended to my rig??
x6800
P5WDH DL
EXTREEM PC2-6400
X1900XTX soon to be CF
Silverstone Zeus 850W

I think 801 is still the best ATM, the others have too many bugs, GL

Thread: ASUS P5W DH - Problems + Fixes Thread

Thread Tools

Search Thread

Rate This Thread

Display

Will

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions