E6600 Conroe + X1900 Crossfire Benchmarks Again

[eva2000]

Yes it's me again

Finally got crossfire working flawlessly after figuring out the ocassional problems I've had since day one.

The system:

• Intel Core 2 Duo E6600 QPGE Step 5/B1 /Corsair Hydrocool 200EX
• Intel D975XBX Badaxe rev304 no volt mods
• 512MB HIS X1900 Crossfire stock HSF
• 512MB Gecube X1900XTX stock HSF
• 2x 1GB Gskill F2-6400PHU2 2GB HZ 6291xxx Micron D9
• 4x 80GB Hitachi 7K80 SATAII Matrix Raid 0
• Pioneer DVD-RW + FDD
• 1KW PC Power Cooling SLI psu

WinXP Pro SP2 fully updated
6.5 Catalyst Official drivers
Guru3D Crossfire User Guide great reading for CF beginners http://forums.guru3d.com/showthread.php?t=181125

The problem:

It seems my Crossfire card was flaky and didn't really like my monitor arrangement setup. I have 20" BenQ FP2091 + 19" BenQ FP91G LCD monitors in dual monitor configuration on my main PC which uses still Gecube 9800Pro Extreme (BenQ FP2091 is on VGA/Analog connector of 9800Pro while FP91G is on DVI port of 9800Pro card).

This main pc is connected to a 4port Aten CS-84A Analog/VGA/PS2 KVM switch. Besides my main work pc, I have 3 other pcs connected to this 4port KVM switch including my 2x E6600/Badaxe rigs and DFI NF4 rig.

The 256MB BFG 7800GTX, 512MB HIS X1800XT, 512MB HIS X1900CF/Gecube X1900XTX cards use DVI-D or DVI-A to VGA adaptors to connect to my KVM switch's VGA/Analog ports.

It seems for Crossfire card in single or CF configuration in DVI-D/A to VGA adaptor mode, WinXP doesn't pick up my BenQ FP2091 monitor at all so monitor settings sometimes get 'out of range' or 'no signal detected' messages or occasionally couldn't set my resolution higher than 1280x1024 when my FP2091 default resolution is 1600x1200 (happened on Cat 6.3, 6.5, 6.6 sometimes and 6.7). Catalyst 6.6 clearly was problematic for 'no signal detected' messages, and Catalyst 6.3 for 'out of range' messages occasionally. But did not get these issues all the time only some of the times.

The solution:

I got fed up of the issue and since my BenQ FP2091 has a free DVI port, I decided to bypass my KVM switch for video signal only leaving my PS/2 mouse and keyboard still on KVM switch port, and connect my BenQ FP2091 supplied DVI-D single link cable from X1900 CF dongle to my BenQ FP2091's DVI port.

Guess what all problems fixed, now my 512MB HIS X1900CF card detects my BenQ FP2091 as a digital panel and sets the proper resolution as 1600x1200 @75mhz (i set it down to 60mhz refresh) and no more 'out of range' or 'no signal detected' messages. Overclocking on X1900CF/1900XTX crossfire is now rock solid with no issues!

Soooo what does this mean ? Time to raid the FM ORB

The benchmarks:

E6600 cooled by my Corsair Hydrocool 200EX unit which uses puny 1/4" OD with Big Typhoon's LGA775 mounting gear. Yes 6mm inner diameter tubing .. puny but still effective for this





Anyway giving Super Pi a rest while i raid the ORB with FM approved 6.5 drivers

1st submission for 3dmark06 @729/859 stock hsf air for X1900CF/X1900XTX combo



Compare Url = http://service.futuremark.com/compare?3dm06=411731

Not too often will I see myself in FM Hall of Fame Top 5

All stock hsf for HIS X1900CF @732/859 + Gecube X1900XTX @729/859

Compare Url = http://service.futuremark.com/compare?3dm06=411744





3dmark05 HOF #4 too now as well http://www.futuremark.com/community/halloffame/

3dmark05 = 22,160
http://service.futuremark.com/compare?3dm05=2138103



More to come soon

[Rovtar]

wow nice

keep it up

[milkcafe]

well done

what about the *ATi Mark* -- 3Dmark05 ??

[eva2000]

thanks

Very cool night for 3dmark benching on stock hsf. Room temp ~19.8C (around 10C cooler than normal, coldest in over 18+ months in Brisbane Australia! ).

Both master & slave @732/864 with 6.5 official catalyst drivers.

3dmark06 = 12,599
http://service.futuremark.com/compare?3dm06=412452



That would put me in #3 spot on 3dmark06 Hall of Fame for now

Here's 3dmark2001 with and without LOD

Without LOD = 67,193
With LOD = 68,798

[bullet2urbrain]

Eva2000 Sorry if you mentioned this before,

What were the CPU Temps? is this corsair comparable to Good Air Cooling? or is it better with the 1/4" ID tubing it seems like a koolance system.

Thanks for the scores and updates

[eva2000]

You can see Big Typhoon vs Hydrocool temps at http://www.xtremesystems.org/forums/...d.php?t=109219

Corsair Hydrocool 200EX with TT Big Typhoon LGA775 mount
CPU bios idle = 31-32C idle in bios (that's 5-8C cooler than Big Typhoon)
CPU windows idle = 24-25C (that's 7-8C cooler than Big Typhoon)
CPU load = 36-39C (that's a full 8-11C cooler than Big Typhoon)

@3750Mhz at 1.5v
Big Typhoon idle = 45-48C room temp = 24.5C
Big Typhoon load = 82-83C room temp = 24.5C
vs
Hydrocool 200EX idle = 34-36C room temp = 21.5C
Hydrocool 200EX load = 65-66C room temp = 21.5C

Bad axe temp is off by +15C to +25C heh

[CraptacularOne]

Still at it eva? Nice scores there:thumbsup: You've still go a wee bit to go to catch me




Not trying to steal your thunder, but get those cards cranking!!!

[eva2000]

which catalyst drivers is that with ? probably won't be able to catch ya, my slave card is maxed at 732mhz core at 1.575v and fsb limited on badaxe/ E6600 cpu you've got a +60mhz GPU core +30mhz mem clock and 200+ cpu mhz advantage... well for now anyway

Try and catch me in 32M though

[Staucher]

That would put me in #3 spot on 3dmark06 Hall of Fame for now

Here's 3dmark2001 with and without LOD

Without LOD = 67,193
With LOD = 68,798

what is LOD?

[bullet2urbrain]

what is LOD?

Level of Detail.

Its a way to display "less quality" images to get better FPS

EDIT: Thanks Eva for the temps... sorry i didnt seet hose before..

[CraptacularOne]

@ eva Those were done with cats 6.6 beta's (faster than official 6.6's) and I'll see what I can do about your 32M times I'm not as adept at those benchmarks

[Gautam]

Still at it eva? Nice scores there:thumbsup: You've still go a wee bit to go to catch me




Not trying to steal your thunder, but get those cards cranking!!!

Damned good stuff there, how are you cooling those cards?

[CraptacularOne]

Damned good stuff there, how are you cooling those cards?

Thanks
Cards are cooled by liquid, with these water blocks....
http://www.frozencpu.com/ex-blc-288.html
As well as heat sinks over the mosfets

[Kinc]

@ eva Those were done with cats 6.6 beta's (faster than official 6.6's) and I'll see what I can do about your 32M times I'm not as adept at those benchmarks

Cat 6.6 beta changes may be represented in 6.7 instead. Have you compared em? I have no cpu atm so mIäm currently stranded.

[CraptacularOne]

Cat 6.6 beta changes may be represented in 6.7 instead. Have you compared em?

Not yet, other than just playing some games (oblivion) I haven't benched this system on the newer ones yet. I have my cards running through the chiller loop aswell now. Not sure if it's going to help me get any higher on the clocks but we'll see soon......

BTW man, that is one SICK 05 score! Well done, well done indeed.......

[Dynasty]

your having too much fun... ....congrats on the CF/Conroe scores...

[eva2000]

your having too much fun... ....congrats on the CF/Conroe scores...

Yup fun fun fun... probably get the 2nd GPU block next week so can H20 cool the cards

[Marioace]

@eva: what PCIe freq are you using?
@Kinc: put ur 7900's in SLI with ur baby

btw nice scores

[eva2000]

101mhz PCI-E

[Marioace]

did you tried a little bit higher?

like 104 or more? it gives to you some extra points

[eva2000]

nah haven't tried higher than 105mhz, i get higher fsb at 101mhz than at 105mhz on my 1st badaxe rig, not sure on this 2nd badaxe board... might try heh

[ahmad]

Is that just one LOD setting for the entire bench (01) or you used different ones?

Kyosen uses a different LOD setting for each test... Talk about Xtreme huh. Are you that patient?

[eva2000]

+3.0 LOD for entire 3dmark2001

[Kinc]

@eva: what PCIe freq are you using?
@Kinc: put ur 7900's in SLI with ur baby

btw nice scores

Seeing eva bench and havong so much fun makes me wanna climb the walls. SinceI don't have any cpu at all. Hopefullt I've orderd one bu they will not be in stock until the 20th aug in sweden.

@eva2000: Have you tested 6.7 in 01? You should get a higher score in nature even with AI activated.

[Viss]

Very nice scores Eva. Tried 2001 with me Opteron 165 last night. Shouldnt your Nature be higher with 2 cards and a cpu that fast?

Got this with single X1800XT and LOD +3.5 for Nature (510fps):



http://service.futuremark.com/compare?2k1=9018973