Originally Posted by NiCKE^
I've tried that Schlingel trust me.
OMEGA3, I used the latest 901, I will try with 0078 in 10 minutes.
Also with 0088 I get that vcore option. But I can't use it, if I use it I get black screen
Maybe I should flash with 0088 and load windows two times and then enter bios on the third reboot?
No, it must be safe the first time.
Not possible to use it though the Vcore-option with 0088....
Huuuum..
Has the character of "AUTO" changed into yellow and white?
Last edited by OMEGA3; 07-26-2006 at 07:37 AM.
Best regards.OMEGA
/N /PBNC but I don't think the order makes much difference. ?
{2012 27imac-3.4i7-680mx-32gb ram-768SSD+External TB Samsung840pro ssd + TB velociraptors-Moto828mkIII/Marantz/Amphion Sound-HPzR30w 2nd monitor}
Auto is always white (in the list it's white and under Jumpersettings it's blue like everything else), if I go to vcore and press enter I will get that list where it's supposed to be different vcore options but it's only auto there
Flashed to 0078 now and rebooted 3 times but no luck, going to try it again 2 times.
xgman: don't think it makes much of a difference. I did it your way first then OPB told me to have /n last.
Last edited by NiCKE^; 07-26-2006 at 07:52 AM.
Intel FTW!
Beanna
If you aren't getting vcore options after a BIOS flash in addition to clearing the CMOS remove the battery when you do so and make sure your mobo is not getting power. Ie unplug or switch off the PSU or unplug the mobo from the PSU. I just switch off my PSU.
0901 BIOS is also here:
http://wiki.p5wdh.de/doku.php?id=downloads:bios
Last edited by Blacklash; 07-26-2006 at 07:56 AM.
Also try disabling C1 control if nothing else works. Which CPU do you have?
btw, malficar, who's that in your avatar?
Got atx pulled out, battery out, cmos reset, nothing but microcode update enable and after flash is done I shut it down and do the things above.
I use a E6600 ES.
Tried 0078 now and doesn't work OMEGA3-san
Maybe I should try 0088 and reboot one time, two times and three times to see if I can use it then?
Intel FTW!
Beanna
Huuum.Auto is always white (in the list it's white and under Jumpersettings it's blue like everything else), if I go to vcore and press enter I will get that list where it's supposed to be different vcore options but it's only auto there
Flashed to 0078 now and rebooted 3 times but no luck, going to try it again 2 times.
Another some seems to have the cause...
To become a blackscreen is doubtful, if it set the Vcore.
Best regards.
Anyone know if this has better support for Kentsfield?
Cheers
MAv
I know someone with the issue, I think, also with an E6600ES Step 5. I don't think he ever got it resolved. :-/ At one point I think he could adjust vcore but it would always be 0.9v actual.Got atx pulled out, battery out, cmos reset, nothing but microcode update enable and after flash is done I shut it down and do the things above.
I use a E6600 ES.
Tried 0078 now and doesn't work OMEGA3-san
Maybe I should try 0088 and reboot one time, two times and three times to see if I can use it then?Maybe its an issue in a select batch? Good luck. :-/
Weren't they supposed to remove ES compatability when C2D got released? Maybe that's what they've done in 0901, Nicke?
asus p5k deluxe (0603)
qx9650 @400x9 1.3v
8800gt @stock
4x2gb corsair 6400c5dhx @5-5-5-15 2.3v
2x mtron msd 6025 16gb raid 0
thermaltake toughpower 850w
lian li pc-s80
If you read the thread you will see that it's not certainly 901 I got problems with, it's _ALL_...
Intel FTW!
Beanna
Though it is not thought it is good...
If not having tried yet,
Please detach CPU once in the state of Hotstart or Cold.
Now here midnight...AT 01:40 Good night.
Good luck!!
Last edited by OMEGA3; 07-26-2006 at 08:41 AM.
Best regards.
Sorry, missed that part.
I had the same problems you have but I fixed it by removing and re-inserting the battery, and as that didn't help you I took a guess.
asus p5k deluxe (0603)
qx9650 @400x9 1.3v
8800gt @stock
4x2gb corsair 6400c5dhx @5-5-5-15 2.3v
2x mtron msd 6025 16gb raid 0
thermaltake toughpower 850w
lian li pc-s80
Start the rig without the CPU?
Good night OMEGA-san and thank you for the help, very appriciated.
Intel FTW!
Beanna
In addition to which, my E6300 ES still works perfectly. So i don't think they did, no.
This still hasn't helped my latency issues, at any speeds above 380mhz on the FSB i cannot run anything other than SPD (which default to 5-6-6-18). No matter if the DRAM divider is set to 760mhz or the lowest. And this stuff can run 900mhz 4-4-4-12 with low fsb.
Conroe E6300 ES
2x1gb Ballistix PC8000
Asus P5W DH Deluxe (1705)
Manli Geforce 7950GT 512mb
Hiper Type-R 480w
Samsung SP250
"What did the quantam duck say?" "Quark Quark"
Nemo-chan, or more appropriately Nemoto Harumi.Also try disabling C1 control if nothing else works. Which CPU do you have?
btw, malficar, who's that in your avatar?
I am at a loss for you fellows that can't get vcore. Until I removed the battery, made sure power wasn't reaching my board, and then cleared the CMOS for a minute, I had the same problem, a vcore with just the "auto" option. Now I have a full range. I corrected the problem back when I had the 0602 BIOS and vcore stuck @ auto.
I'd say try switching off your PSU and not upnplugging the mobo, or if it doesn't have a switch unplugging the cord from it.
Here's how I do it:
Remove power from the computer by pulling the plug or switching the PSU off.
Remove the Battery.
Move the CMOS jumper to CLEAR.
Press the Start Button on the case to drain the capacitors.
You may leave the board in this condition for as long as it takes to clear the CMOS. If a short 30 second clear or a 15 minute clear doesn't work, try an 8 hour clear then a 24 hour clear.
Move the CMOS jumper to Normal.
Replace the Battery.
Apply power to the computer by plugging the power in or using the switch on the PSU.
Press the Start Button to power the computer up.
Press the Delete key on the Keyboard.
Once you enter the BIOS set the DATE and TIME then Load Optimized Defaults.
Last edited by Blacklash; 07-26-2006 at 10:21 AM.
Similar experience here, no vcore on 0502, flash to 0701, no vcore, reset CMOS (didn't even take the battery out), couple of reboots and the vcore and vdimm control became available. I find that the easiest way to flash BIOS is with the Asus BIOS flashing tool and a USB data key.
I guess I should also mention that I am using the E6700 ES Step 4 QLLO if that matters at all.
Last edited by Igor01; 07-26-2006 at 10:49 AM.
My "almost silent" PC
Antec P180 Black case | Seasonic S12-600 PSU
Intel E6600 @3.4 | ASUS P5W DH | 2x1GB OCZ Platinum PC2-8000 XTC
NVIDIA 8800 GTX | Dell 30" LCD | 2.something TB storage | Creative Labs X-Fi | Klipsch Pro-Media 4.1 speakers
nice bios so far, i like the oc profile
retired computer enthusiast
So far I have personally had no headaches with vcore on both a Conroe 6700 B1, and a Presler 920.
What happens if you set vcore in AI Booster?
Is it possible to activate the ECC in the bios ?
If i were you I would stick with the 901 bios from eher on in and leave eveything unplugged and unpowered like it was said above for a while. Somewhere in the process of clearing, restting rebooting etc. I think your options will return. Obviosly this should not be happening at all regardless, and Asus should look into this at this point.
{2012 27imac-3.4i7-680mx-32gb ram-768SSD+External TB Samsung840pro ssd + TB velociraptors-Moto828mkIII/Marantz/Amphion Sound-HPzR30w 2nd monitor}
can you flash the BIOS from within the BIOS on this board - I think there is an option?
Cheers
Mav
After flashing to Bios 0901, everything within the BIOS options seem to be working fine. However, cpu speed and fsb are not reading correctly from within Ai Booster eventhough cpu speed is reported correctly under My Computer properties. All these readings were detected correcly by Ai Booster with Bios 0701. Is anyone else having this problem?
I use CPUZ, not AI booster, if someone is kind enough to answer my questions - then I will be able to flash (with confidence), try it out and report back.
Cheers
Mav
Worked fine for me!
Posting Permissions
Reply With Quote
Bookmarks