XS Yonah T2600ES competition !!!

[M.Beier]

sweet CPU Stephen

[NiCKE^]

Is it the 290fsb chip stephen?

[s7e9h3n]

Is it the 290fsb chip stephen?

Yes it is....we'll see soon if it can reach that speed....someone really needs to come up with a Vcore mod that allows for higher than 1.64V. This cpu seems to be more limited now by vcore as opposed to FSB.....

[NiCKE^]

How much do you need? 5v? :P

[s7e9h3n]

How much do you need? 5v? :P

LOL...1.7 - 1.8 would be nice

[njkid32]

I'll look for the explosion from here

[Gamer]

joint the dark side there ?

[NiCKE^]

Other way around, he came where the light is

[s7e9h3n]

Ok, tested the cpu last night on my autocascade and I've learned something new.....-80C insulation doesn't work too well @ -100C temps I'll have to do some more insulation before trying again since the board is acting up. FWIW, I reached 295x13 for a short bit before the board locked up and didn't want to boot again ~-103C IDLE temps, -102C LOADED

[G H Z]

I thought your Auto was running -150° now or something? Hurry up and insulate that rig properly

[s7e9h3n]

I thought your Auto was running -150° now or something? Hurry up and insulate that rig properly

Those temps were for for fun (It actually made it down to -162C). With a decent capacity, the numbers will have to be quite different. The temps I reported in my last post are from an probe in the cold plate on top of the core. Actual evap temps should be ~-115C....

[M.Beier]

Nice CPU mate

Now get rid of that autocascade and get some LN2 for the sucker - 4ghz yonah action, common

EDIT: GAH I need a new mobo, but this freakin' contry still havnt got them, GHZ's past me in 01SE - last time I looked I was LAST on front page, now this sucks

[s7e9h3n]

Nice CPU mate

Now get rid of that autocascade and get some LN2 for the sucker - 4ghz yonah action, common

EDIT: GAH I need a new mobo, but this freakin' contry still havnt got them, GHZ's past me in 01SE - last time I looked I was LAST on front page, now this sucks

No need....I think I can do 4ghz with the auto

[M.Beier]

No need....I think I can do 4ghz with the auto

AYE CARAMBA

... Just dont touch 01SE dude!!

[s7e9h3n]

AYE CARAMBA

... Just dont touch 01SE dude!!

Oh...just remembered.....I wasn't @ -100+C when I saw teh 295FSB...I forgot had actually turned the cooling head off. IIRC, temps on the cold plate were ~-48C

[Silves]

Nice CPU mate

Now get rid of that autocascade and get some LN2 for the sucker - 4ghz yonah action, common

EDIT: GAH I need a new mobo, but this freakin' contry still havnt got them, GHZ's past me in 01SE - last time I looked I was LAST on front page, now this sucks

You can buy one here http://www3.atelco.de/8AvRLj_yBr9-Mw...aid=6636&lid=2
The shipping charges for Denmark are 17,50€ http://www2.atelco.de/7AewJFNvVOjsRx...oagbprivat.jsp
Or here http://www2.hardwareversand.de/7VXqw...aid=6636&lid=2

[fredyama]

Update

By fredyama(PRTeamJapan)
M/B: AOpen i975Xa-YDG#2 Mods by duck
Cooling: LN2

modPI 1.5 XS 1M: 15.984s @3733.7MHz (FSB287.2MHz x 13)


modPI 1.5 XS 8M: 3m01.953s @3733.5MHz (FSB287.2MHz x 13)


modPI 1.5 XS 32M: 14m20.000s @3719.2MHz (FSB286.1MHz x 13)

[albertwesker]

T2600ES 8
AOpen i975Xa-YDG (vdimm mod)
4x512 MB Centon Advanced @ 2,3 V
Vapochill LS
1,5V

[s7e9h3n]

Last night, I found that I didn't have any more Ceramique left so I ended up running the yonah without re-insulating the board as I had originally planned - BAD IDEA I ended up spending the entire night pulling my hair out trying to figure out wtf was causing the cpu to act so erratic. I messed with timings, voltages, memory slots, etc. - everything I could think of but I was only able to manage a few completed Spi runs @ NOWHERE near the cpu's top speed :

Evap temps @ ~-115C IDLE, ~-114C LOAD







These runs were basically done a couple of minutes before I shut down for the night. As I reached around the autocascade to turn the unit off, I noticed what had been causing my frustration for the last couple of days .....



This wasn't just a thin layer of frost -> rather it was a SOLID chunk of ICE that took ~5 minutes to melt with a hair-dryer on the "HIGH HEAT" setting . Luckily the hardware seems to be in good condition still, so hopefully I'll be able to get in a few nice runs sometime this weekend. The cpu's got quite a bit more left in her - this was done earlier in the night, most likely when that iceberg was still in it's infancy



4ghz is within reach

[snatchmonkey]

300FSB!!

Congrats

[Gautam]

Amazing stuff Stephen. I got an "iceberg" as well in exactly the same spot... I don't think it caused me any trouble since I sorta always ran with some ice in various spots.

Now, isn't it nice to move to a platform where lower temps get you a higher FSB rather than a lower one? (HTT)

[s7e9h3n]

Amazing stuff Stephen. I got an "iceberg" as well in exactly the same spot... I don't think it caused me any trouble since I sorta always ran with some ice in various spots.

Now, isn't it nice to move to a platform where lower temps get you a higher FSB rather than a lower one? (HTT)

LOL...this wasn't any ordinary iceberg, this one could have sunk the Titanic as well . Stuck a hair -dryer on it and it basically didn't start melting for a good 2-3 minutes. I have a feeling it was wreaking havoc on my Vcore as it was all over the place (even for the Aopen). Also, I have a feeling it had something to do with my problems with the setup on my last boot attempt. Basically, I opened up clockgen and tried to set the FSB. Well, somehow the cpu clocked DOWNWARDS and was stuck @ 1700Mhz no matter what I did. I tried the Aopen OC utility but the FSB wouldn't budge and upon re-opening clockgen, ALL the OC buttons were gone only the "Clocks" button was available.......

[Tyrou]

Congratulations !!!

Stephen, you finally overtook my T2600 WR, 300fsb is a hell of an achievement. The most impressive is to it with a single compressor cooling, where mine needs three to work

One more time :

[GoriLLakoS]

Well done stephen....keep this toy..i am comming to catch you over there....

[s7e9h3n]

Congratulations !!!

Stephen, you finally overtook my T2600 WR, 300fsb is a hell of an achievement. The most impressive is to it with a single compressor cooling, where mine needs three to work

One more time :

Thanks my friend, but this cpu is nothing if it can't run @ these speeds. Yours is a gem, especially considering that you hadn't even done the vcca mod