Ultra-D Rev AD0 - Does it report lower temps than older revisions?

[IvanAndreevich]

Question: I'm just comparing the temps I'm getting on it with an older revision SLI-DR and they are very low About 5-8 degrees lower than what I would expect. Anybody else have similar experiences?
Apparent answer: YES, AD0 seems to be reporting a lower temperature, just like the Expert.

[Lastviking]

I'm just comparing the temps I'm getting on it with an older revision SLI-DR and they are very low About 5-8 degrees lower than what I would expect. Anybody else have similar experiences?

Yes same for me AD0 Report abit lower temp same with Expert and Venus.

[lawrywild]

mine are about right... I think..

[Nephilim]

I just got my Rev AE1 I'll let u know if that's any different again

[IvanAndreevich]

I just got my Rev AE1 I'll let u know if that's any different again

Is that physically different

Lastviking
How much lower temps does AD0 report, compared to the older revisions?

[eBoy0]

In speedfan i see a 2c lower load temp, lemme ask you is your vdimm .07 too high? EX: set to 2.8 an its 2.87?

[lawrywild]

In speedfan i see a 2c lower load temp, lemme ask you is your vdimm .07 too high? EX: set to 2.8 an its 2.87?

YES!!

and checked with DMM also, SG shows about 2.84, DMM - 2.87, Bios - 2.88

[Supertim0r]

my X2 @ 2.95ghz 1.43v = 38c loaded under th TT BT with a panaflo l1a
with the A8N32 i'm @ 46-48c @ 2.9ghz 1.39v

you can adjust the temp with the lastest beta bios 2006/3/29 http://www.lejabeach.com/DFI/dfinf4ultra/NF4LD329.zip

[ozzimark]

no difference from my AC0.. but that had the same PCB layout, so...

i do KNOW that the cpu temp is reported low for me, because there's no good reason that the cpu temp should display 2-3c lower than water temps when the water gets >40c, as measured by two seperate, but fairly reliable temperature sensors

[Repoman]

In speedfan i see a 2c lower load temp, lemme ask you is your vdimm .07 too high? EX: set to 2.8 an its 2.87?

Mine does that too.. it used to be about .06 over but now it's raised to .08 I'd really like to have access to 2.5v and a little lower..

I wonder if a modded BIOS is possible to allow lower voltages for Infineon based stuff etc

[eBoy0]

Sorry to thread hog, but I think was overlooked in my thread does anyone's A.D0 look like this?
http://i5.photobucket.com/albums/y17...0/P1010268.jpg
The 4th led which should be lite up until DMI check isn't lite, instead the 3rd takes it's place.
Also vdimm problem can be fixed w/ a vdimm mod.

[thunderstruck!]

I just got my Rev AE1 I'll let u know if that's any different again

Where did you get it?

[[XC] 4X4N]

I have posted about this before, and it didn't seem that many people were seeing the same. My AD0 shows temps about 10 degrees lower than my A02. I had an expert for a while and the temps were reporting 10 degrees lower on it also. As for vdimm, both versions show about .04 higher than what is set in bios.

[IvanAndreevich]

I just got my Rev AE1 I'll let u know if that's any different again

Let's see some photos

[Nephilim]

Hi guys,

Sorry I didn't see the replies. I got the board from nintek in Australia.

temps identical to my r.AB0

Running 11/14 bios out of the box.

Looks physically identical. Here are pics:



Some heatsinking and insulation:

And she's good to go sorry couldn't resist showing off my pretty pc again hehe.



Yes the 11x multiplier is still on that chip, so it appears independent of the mainboard, it is still the max available though... so no magic 165-185 madness yet.