Asus A8N32-SLI initial impression....WOW!

[thinkingbear]

Does this board work well with Crucials Ballistix 1GB sticks?

I think when this thread started Ben085 was using Crucial Ballistix in the original screen shots and overclocks, only after they died did he switch to Mushkin Redlines. I see you already have your Ballistix, I just went by Crucial.com today to order and they have pulled all the 1GB DIMMs from stock. I contacted a rep and they said they are in disussion with the manufacturer on whether they will be back in stock again at some point or whether they are EOL. Just too many burnt out RMA's I suppose.

[Blacknach]

Hi, I have a problem when reset or change settings in bios, this not run, only black screeen, i have to turn off power and he go perfect, this is in opty 148@2900, with 1.475 stable at prime and the bios 1009, the problem apear above 2750, htt 290 divider 166, with adata tccd i don´t now what cause this, somebody can help me, tccd in this mother sucks, i can´t pass 250 estables
sorry for my english

thanks

[Jailer]

I've had really good luck with my new Gskil 2x1Gb GBHZ. 270 1:1 at 2.8 volts 3-4-4-7.

It will go higher but I haven't tried finding the limit yet. It will go 273 1:1 with no errors in memtest 12+ hours, but my 148 mem controller starts flaking out at that speed using the default multi. Still very good performance and speed for under $200.

http://www.newegg.com/Product/Produc...82E16820231021

[CODE 4]

Hi, I have a problem when reset or change settings in bios, this not run, only black screeen, i have to turn off power and he go perfect, this is in opty 148@2900, with 1.475 stable at prime and the bios 1009, the problem apear above 2750, htt 290 divider 166, with adata tccd i don´t now what cause this, somebody can help me, tccd in this mother sucks, i can´t pass 250 estables
sorry for my english

thanks

I just put a 148 in yesterday and i am having the same issue. No post, shut down and then she goes fine. It happens when I put more than 1.525 volts to the cpu with more than 2950mhz.

[Blacknach]

I just put a 148 in yesterday and i am having the same issue. No post, shut down and then she goes fine. It happens when I put more than 1.525 volts to the cpu with more than 2950mhz.

What bios are you running?, i´m waiting a new bios to my tccd, can´t pass 250 stables

[Raver]

I've read all of this thread and I know that some programs dont report voltages and temps correclty but who do we trust?

BIOS Jumper Free Configuration
Over Volt
CPU Disabled
NB Disabled
SB Disabled
HT Disabled
FID/VID Manual
Proc Volt 1.4125v

Hardware Monitor reports the following

CPU Volt
varies between 1.456v to 1.472v
Temps
CPU 39Celcius/102Fahrenheit <----- higher temp here is normal, in BIOS cpu is running like under load.
Syst 32Celcius/89.5Fahrenheit


PROGRAMS

CPU-Z ver 1.31 November 2005
Core 1.400v

AiBooster ver 2.00.70
Core 1.4125v
System temp 32celcius

PCProbeII ver 1.00.43
Core 1.470v
CPU temp 35celcius Idle
MOBO temp 32celcius Idle

Everest Ultimate Edition ver 2.50.480
Core 1.470v
CPU temp 35celcius Idle
MOBO temp 32celcius Idle

SiSoftwear Sandra professional Unicode (Win32 x86) 2005.1.10.37
Core 1.46v
CPU temp 35Celcius/95Fahrenheit Idle
MOBO temp 32Celcius/89.6Fahrenheit Idle

@Marios.

I see that you have ClockGen running, I downloaded the one for nForce4 but it doesnt show like yours, can you tell me which you downloaded for this mobo?

[Deus Excalibur]

Those of you who don't have the warm boot problem while OCing, what kind of sytems are you using? Like do you have a IDE or SATA CD/DVD ROM, etc.

I cranked up all the voltages and all voltages at the max does nothing to cure the problem.