NF3/NF4 & BH-5/BH-6/UTT - Highest stable clocks - REPORT IN !!!

[Monge]

2*512MB Twinmos Speed Premium PC3200 (UTT/CH-5 Week 03 Year 05) at 9x 262MHz@3.4v on DFI NF4 Ultra-D and Venice 3000+:

[NISCO PT]

my setting with 2x512 mushkin redline xp4000 3,5v bios 623-2 in DFI sli-d


the bests stable i can get until now

all the memory setting in bios:
180
enable
1,5
02
00
02
07
16
02
02
02
02
2064
01 bus clock
enable
increase skew
0
level 5
level 2
07,0 nano segundos
fastest
05,0 nano segundos
256
disable
16x
07x
disable(4 bursts)

[masni]

here is one interesting result...

dfi ultra-d, venice 3000+, 623-2 bios and...

1x512mb corsair pc3500c2 rev1.1 BH-5 + 1x512mb twinmos pc3200 1A4T BH-5...

<a href="http://imageshack.us"><img src="http://img288.imageshack.us/img288/6460/260httsuperpi32mbzutislotovi9l.jpg" border="0" width="1024" alt="Image Hosted by ImageShack.us" /></a>

can you guys tell me what settings effect super pi 32mb stability most...?? it seems i can't get my sp 32mb calculation finished past 260htt...maybe some other bios...??

[Eldonko]

4000 Redline & 0704-2BTA.

[Ozan Baseski]

Hello everyone. I tested my new bh5 OCZ EL DDR PC 3500 Platinum Limited Edition sticks and they managed to finish the test at 270 mhz at 3.5 volts Here are the results

[GUFY]

Geil One BH-5, DFI NF4 Ultra-D@SLI-D, OCZ Powerstream 520W, SD 3700+

[HiJon89]

Geil One BH-5, DFI NF4 Ultra-D@SLI-D, OCZ Powerstream 520W, SD 3700+
http://img377.imageshack.us/img377/4...m270mhz7fu.jpg

Minimum x9 multiplier required

[GUFY]

Geil One BH-5, DFI NF4 Ultra-D@SLI-D, OCZ Powerstream 520W, SD 3700+



Sory my mistake, but may ram can do even better

[GUFY]

Bios is 623-2, tref 2592, Drive stength 7 and Data Drive stength 3.

I hope to rich 275 MHz with this ram.

[bachus_anonym]

*** Thread updated ***

Yay! 83 entries! Keep those results comming, guys! Thanks a lot

BTW, I cleaned up this thread a little...
Let's try to keep it straight up to the point - screenshots only, please Nice & Clean...

[Monge]

bachus_anonym: Thanks

Vdata UTT/BH-5 (Week 16 Year 05) 9*263Mhz@3.6v on DFI NF4 Ultra-D/Venice 3000+ DPMW:

[Tibu]

Corsair LLPT 3200 BH5 @265fsb
Trying for 270 now.

[lemonlime]

A64 3500+ Winchester
DFI NF4 Ultra-D
2x256MB Kingston HyperX PC3500 BH-5
1.5-2-2-0 1T @ 271MHz
3.65V (extra voltage does very little to help)
Memtest stable for many hours

Note: CPU not totally stable at 2.71GHz, so 10x multi cant be used for 32m.. I can 3dmark fine with 2.7, so these screenies were done with 9x multi.

[toreide]

OCZ VX3200, it does max 254 mhz. 32m time was 24m 43.109sec.

[|SiLA|]

for now add me these freq

i can do better tho'





4x512 GSkill GBGH mobo sli-dr

[|SiLA|]

here's another update from here

[KenLau]

Corsair XMS PC3200LL REV.1.1 256mb x2
274.5 (DDR 548) Vdimm 3.6V
Venice 3200+ @ 305x9 = 2745Mhz
DFI NF4 Ultra-D (Bios 623-3)

[Super Nade]

Posted this at OCForums, hope the duplication won't hurt


New settings with 512 x 2 Muskin Lvl II blk PC3500-BH5
-----------------------------------------------------------------------
I'm using the 6/23-3 (still TCCD specific, but hey I'm getting good results!)


Last Updated:Oct 23, 2005
Motherboard: Lanparty Ultra-D
Bios: 6/23-3
CPU: 3200+ Venice (Rev E3)
VC: BFG 6800GT 81.85
OS: Windows XP Pro w/SP2
Ram: Mushkin lvl 2 Black PC3500 (Original BH-5) In the Yellow DIMM slots
Chipset Drivers: Revision 6.66 (w/out IDE)

DRAM Timings:

• Ram Multi 200 1:1
  CPC ENABLED
  Tcl 2
  Trcd 02
  Tras 02
  Trp 02
  Trc 07
  Trfc 12
  Trrd 02
  Twr 02
  Twtr 01
  Trwt 02
  Tref 3072
  Twcl 01
  Bank Inter EN
  Dynamic Skew Control Increase
  Skew Value 255
  DRAM Drive Strength 06
  DRAM Data Drive Strength 01
  DRAM Response time: Fastest
  Max Async 9ns
  Read Preamble 5ns
  Idle Cycle 128
  Dynamic Counter EN
  R/W Que Bypass 16X
  Bypass MAx 7X
  32 Bit Gran DIS

Voltages etc:

• HTT 270
  LDT X2.5
  Cpu Multi X10
  PCE-I 100
  Vcore Startup 1.525
  Vcore 1.450
  Vcore Special 113%
  LDT V 1.4
  Chipset V 1.7
  Vdimm 3.6 + DRAM .03 Enabled

Extra Notes and observations:

• - If TWCL was set to 02 instead of 01, I had to reset the CMOS. TWCL always at 01
  
  - Data Drive strength can be set to level 8, but I'd have to loosen a few timings. I can choose between 6 and 8. 6 seems t0o get me more BW.
  
  -If Twtr was set to 01/03 instead of 02, there was no BOOT.
  
  - I tried tREF to AUTO and then picked off 3072 from a64 tewaker.

Proof of stability and other links:-
http://valid.x86-secret.com/show_oc?id=45474

[bachus_anonym]

*** Thread updated ***

Thanks a lot for great results and participation in this little fun we have here

[PsYkHoTiK]

Here's mine.
A64 3200+ Venice, DFI NF4 SLI-DR (BIOS 623-2), 2x512 OCZ Gold VX PC3200, OCZ Powerstream 520w.

Trying to see if I can squeeze more without increasing the DRAM voltage...



EDIT: How dumb of me. I blocked out the bit of SuperPi that shows that I ran the 32m test. I'll re do it if it's required.

[KenLau]

bachus_anonym
Thanks for updated
Also,here's a new record of mine, 279mhz on the bios 623-2 .
Next steps will try to removed the stock heatspreader,to see if it can break the barrier of 280 mhz .

[uOpt]

OK, had to delete my first post, but after an evening of fiddling I am at SuperPi 32 M and x9 multiplier.

This is my Opteron 146 CABYE 0540 FPAW at 1.65 Volts and 4x 512 MB Geil One BH at 3.6 Volts.

Big Typhoon and 80mm fan directly only the 4 RAM modules.




I am working on doing the same thing with a x10 multiplier as we speak. [done, this is the x10 shot]

[bachus_anonym]

*** Thread updated ***

It looks like the pace is a little slower this time around Come on guys, keep me busy here

Thanks a lot for sharing some nice results

[gigi77]

My Config.

A64 3000+ Venice step E6
DFI NF4-D
2x512 mb GEIL ONE W
ZALMAN CNPS 9500

Thanks to All my Friends
This is for you

The Return of BH IC

[uOpt]

Here is the best I can do for now - 271 MHz @ 2-2-2-5

Geil One BH 2x 512 MB @ 3.6 V. CABYE 0540 FPAMW @ 1.6 V, DFI SLI-DR, OCZ 520 W.



Does prime95 at 268 MHz same settings.

EDIT: Win2k; LargeSystemCache=0