Overkill Cube ( AKA Snowflake)

[MagisD]

Overkill Cube

*This history/story being updated for the sale.....*

Please excuse my ramblings, this is half for myself I think better after I express my idea's verbally or Written. Half for everybody else so they might get some idea's

New project most of stock ordered. I know there's a few things I left out ext vid spacers for rad connections, Screws etc

I had to re-think and redo most of what I had planed due to not being about to actually mod or even sleeve due to carpal tunnel I simply don't have the fine motor control to do a Good job. 5-10 minutes of fine or steady handed work and my hand starts to shake.

I decided to get the good painkillers and try ;-)

Everything here is ordered /on its way/ Sitting in my closet.

Mountain Mod Extended Ascension Anodized aluminum with custom panels ( system colors Black/gunmetal gray and clear tubing)
1 x Delrin Vandal Resistant Illuminated Switch 16mm Black - White Dot
1 x Delrin Vandal Resistant Illuminated Switch Black - 22mm White Ring
1 x MNPCTech - Mounting plate for 16mm/22mm Vandal Resistant Switches - Black


Internals
Intel D940
Evga X58 Sli Le With EK full board Block
ATI Powercolor 5870 LCS ( pre-installed EK Full board Block ) ( triple eyefinity on 23'samungs)

Changed to

i7-960
Asus Ramage extreme II
MSI Gtx 570 sli
all with koolance Waterblocks

Indigo Xtreme Tim
Koolance 360 Rev1.2 Cpu block
Intel x25-m 160gb X2
6gb Corsair Dominator-GT 3X2GB DDR3-2000 CL8-9-8-24
Mips Ram Water block Black Delerin
Corsair AX1200 modular PS

Watercooling/Fans


Single loop

2x Swiftech MCP35X with
Koolance 80mm OD res with Ends
6 x Swiftech MCR-420 , 3 front 3 top
28 x Scythe 1850 gentle Typhoons
28 x FilterRight 120mm Black Aluminum Fan Filter
1 extra fan and filter in 5,1/4 bay
2 x IandH Silver KillCoils


Fittings/attachments

1 x VLV-XTSPLB Drain Valve, Brass
14 x NZL-V10-16KG2 Nozzle Pair, Compression [For ID: 10mm (3/8"); OD: 16mm (5/8")]
2 x BKT-TK120F Reservoir Bracket, 120mm
2 x COV-TKBTM Reservoir Nozzle Base
3 x PRT-XGK Coolant Fill Port / Drain Valve
2 x VLV-BL1X2 Ball Valve
4 x NZL-LXG1P Fitting Pair, Swiveling Elbow
4 x ADT-XMF-L Nozzle Coupling Adapter, Male-Female, 20mm
10 x ADT-SMF Swiveling Coupling Adapter, Male-Female
4 x ADT-SMM Swiveling Coupling Adapter, Male-Male
8 x NZL-DXG-V2 Fitting Single, Swiveling 45-Degree (V2)
2 x VLV-VL002K Pressure Valve

And then some I added a lot can't remember

Decorative

MDPC-X ( Yes I have gone Insane)

1x MDPC Sleeve-Kit
SL-K1-BK
1x Pin-Remover 4-Pin - Save My Wallet
PR-SMWE
1x Pin-Remover by MOLEX - The Original
PR-MOLEX
2x Cable-Management-Clip SMALL - BLACK
PC-S-BK
3x Cable-Management-Clip JUMBO - BLACK
PC-J-BK
3x Cable-Management-Clip BIG - BLACK
PC-B-BK
3x Cable-Management-Clip MEDIUM - BLACK
PC-M-BK
3x Snap-Caps SMALL
SNAP-S-BK
1x Sleeve USB - BLACK
SL-USB-BK
1x Sleeve SATA - GREY
SL-SA-GY
1x Sleeve SMALL - GREY
SL-S-GY
10x 3-Pin MOLEX BLACK - Housing
HO-3PF-BK
1x MDPC Crimping-Tool
CR-TOOL-X
3x Heatshrink SATA - BLACK
HS-SA-BK
2x Snap-Caps MEDIUM
SNAP-M-BK
2x Brainwasher UNC and M4
BRAIN-UNC
1x Crimp contacts for fans
CR-FAN
1x Brainwasher M3
BRAIN-M3
1x Crimp contacts FEMALE for ATX, PCIE, EPS
CR-ATX-F
2x Crimp contacts MALE for ATX, PCIE, EPS
CR-ATX-M

with a bunch left over

Custom Case Specs
MM Extended Ascension – Anodized Black
Standard Big window left and right
Triple Quad Top
Triple Quad Front
Horizontal Back

Custom Cut Horizontal Back (Triple fan on top, MB Slot middle, 3x5 1/4 Bay and Dual PS holes on bottom )



Custom cut front Triple quad Going smooth front



Tops Normal triple quad, moved down to 2 loops/ fillports Center spot is power/reset. Drilling holes is about the extent of my modding ability now.




Case should be here Monday the 13th build will start then And the bad Sony X10a Pic's( Only camera I have)

Wish me luck