Problems with EK HD 5850 backplate & 780i SB waterblock + my WC loops

[lonkny]

Hey all,

Thanks for the great site and info. I have been lurking for a while now as I refresh my WC setup. I recently upgraded my case from a Smilodon to a Corsair 800D and have decided that I'd take this time to also refresh my system and WC'ing. My old water cooling setup was definitely a "beginner's loop" and used an Exos-2 w/mostly Koolance blocks. Have learned a lot since then, and am ready to take things up a notch or two.

I upgraded my 8800GT with an XFX Radeon HD 5850 XXX Edition card, and of course had to get a full coverage block for it. I also made a couple other minor upgrades, the best of which was getting an SSD for the OS HDD (wow), but much of the hardware remains the same (at least for now...). I consider it a "refresh" build...

I have decided to go with 2 loops since I now have plenty of room, and enough blocks now to warrant 2 loops (CPU, NB, SB, Mosfet, VGA). Most of it will be internal, but the 2nd RAD & Res/pump will have to be mounted to the back of the case because I have already run out of room (at least without making significant modifications)... Here is a pic & list of equipment so far, along w/the proposed loop configs:



Loop 1:
Res1 = EK Multioption 250 w/Anticyclone
Rad1 = Swiftech MCR320 w/6 Scythe Slipstream SY1225SL12SH push/pull
Pump1 = Swiftech MCP655 w/EK D5 Top
SB = EK 790i Southbridge Block
CPU = Koolance CPU-340
Mosfet = Koolance MVR-40

Loop 2:
Res2 = XSPC DDC Res Top
Rad2 = Black Ice SR1 140mm Low Flow w/Noctua NF-P14FLX & Corsair 140mm
Pump2 = Swiftech MCP355
NB = Danger Den 780i NB Block
VGA = EK FC-5850 w/RAM Backplate

Misc:
Fill Port = Danger Den Black Aluminum
Tubing = Feser Black 1/2" ID 3/4" OD, Tygon R3400 7/16" ID 9/16" OD, Koolance Orange 1/2" ID 5/8" OD
Pump Bracket = (UN)Designs Infinite DDC Pump Bracket, Vertical Version
Control = T-Balancer BigNG, MiniNG, Analog Sensor Hub
Flow Meters = 2 x Koolance INS-FM17
Temp Sensors = 2 x Koolance SEN-AP006G
Display = iMon VFD 5.25"
Fittings = various Enzotech, Bitspower, & Koolance

Hardware (partial):
Motherboard = eVGA 780i
CPU = Core2Quad Q9550
RAM = Corsair Dominator 1066
Video Card = XFX Radeon HD 5850 "XXX Edition"
Case = Corsair Obsidian 800D
PSU = ABS Tagan 900W
Sound = Creative X-Fi Fatal1ty Professional Edition
OS HDD = OCZ Colossus 256GB SSD
SATA/SAS RAID = JMicron JMB363, Highpoint RocketRAID 2642 (not worth the $$! The $30 JMicron controller is better)

I still haven't figured out where to put the temp sensor for loop 2, and the flow meters for both loops. Any suggestions/recommendations are much appreciated.

And now for my issues:

The EK 780i Southbridge block uses a thumb nut to tighten the block to the board, along with a 12mm long screw. Problem is, when tightened it is much longer than the motherboard tray spacers that the board sits on! I'm surprised nobody has mentioned this issue in the past, but I haven't been able to find any info on this problem elsewhere... Here is a pic:



The case motherboard tray standoff screws are approximately the same height as going from the bottom of the motherboard to the bottom of the thumb nut in the above pic... so I suppose I can file the screw length down so the screw ends at the bottom of the nut rather than going through the nut and down another 5mm or so... but perhaps I'm mounting it wrong somehow? Here are the EK instructions which I followed closely:

http://81.90.180.2/ekwaterblocks/shop/EK-IM/EK-IM-3830046991317.pdf

And a pic of my motherboard with the block installed:



Let me know if anyone has experienced this or similar issues and if there is a better solution out there... I'm not looking forward to having to remount the block... much appreciated!

The 2nd EK block issue I'm having is with the HD 58X0 backplate that goes with their 58X0 block. Again I followed the instructions to a T:

Block install:
http://81.90.180.2/ekwaterblocks/sho...1109835104.pdf

Backplate install:
http://81.90.180.2/ekwaterblocks/sho...1109855027.pdf

It clearly shows for the 5850 to leave the one screw out. However, there is a small chip on the back of the 5850 PCB that this screw hole is pressing up against, and very hard too:







I own the XFX "XXX" version of the 5850 which is supposed to be a reference PCB design, simply factory overclocked. I didn't notice this issue at first, until I saw that the backplate was actually bending when the screws were tightened!

Again, I suppose I could file down this one recessed screw hole, but am surprised I haven't heard of others with the same issue. I am sure the backplate is screwed in properly - there really isn't any way to screw it in incorrectly - it just wouldn't work.

If anyone has any ideas on these two issues, it would be greatly appreciated... thanks!!