fatality an8/gskill F1LA week 440/300htt

[chew*]

For those having issues running prime stable(24/7) and memtest86 stable(10 passes no errors) with an Abit AN8 try these timings with 2.8vddr and 1.4vtt.

[bachus_anonym]

Very nice, bud... :thumbsup: If you could do me a favor and run SuperPi 32M at highest stable TCCD clocks, it would be very nice contribution to my thread about TCCD overl:banana::banana::banana::banana:s It's in my signature below

On the side note, you might want to change that .BMP screenshot (2.3MB) to .PNG It can be too big for some members, without high-speed Internet

[chew*]

Very nice, bud... :thumbsup: If you could do me a favor and run SuperPi 32M at highest stable TCCD clocks, it would be very nice contribution to my thread about TCCD overl:banana::banana::banana::banana:s It's in my signature below

On the side note, you might want to change that .BMP screenshot (2.3MB) to .PNG It can be too big for some members, without high-speed Internet

ok what proggie should i use to make the the .bmp to .png and as far as this tccd goes 300 is max at these timings however if i back them off some it will go higher. If i could give it more volts like 2.9 it would do better it did 320 at 1.85v 2.5-3-3-6 in a neo 2 yesterday in vlads rig (he tested it for me before i picked it up to make sure we didnt have to send it back). wish abit gave me more vdimm

[ben805]

Despite the fact that everybody oppose and strongly against using the 1/2 multiplier, I for one will stick with the 8.5 multiplier on this POS 3000+ winnie, as I found the 8.5 works best for my rig, it's true that running 8.5 x 313 only yield about 295~ memory clock (memtest 1.55 reports 295), but who the hell care if it's putting down some decent numbers and able to passed all the tests with flying color?? this is a 24/7 machine, absolutely memtest, Prime95, and SuperPI 32M stable, Loop 3Dmarks all day and all night long, I'll let the numbers speak for itself...


oops, here's the spec:

3000+ Winnie 0444MPM (2.661Ghz @1.61v)
XP-90 + Enermax 90mm fan
GSKILL PC4800 512LA
DFI LP Ultra-D
PCP&C 510 SLI
MSI 6600GT
EMU0404
Sil3114 SATA Raid Controller
36G Raptors x2 (Raid-0)
NEC DVD Burners x2
80mm Case fans x5

[JNav89GT]

Despite the fact that everybody oppose and strongly against using the 1/2 multiplier, I for one will stick with the 8.5 multiplier on this POS 3000+ winnie, as I found the 8.5 works best for my rig, it's true that running 8.5 x 313 only yield about 295~ memory clock (memtest 1.55 reports 295), but who the hell care if it's putting down some decent numbers and able to passed all the tests with flying color?? this is a 24/7 machine, absolutely memtest, Prime95, and SuperPI 32M stable, Loop 3Dmarks all day and all night long, I'll let the numbers speak for itself...


oops, here's the spec:

3000+ Winnie 0444MPM (2.661Ghz @1.61v)
XP-90 + Enermax 90mm fan
GSKILL PC4800 512LA
DFI LP Ultra-D
PCP&C 510 SLI
MSI 6600GT
EMU0404
Sil3114 SATA Raid Controller
36G Raptors x2 (Raid-0)
NEC DVD Burners x2
80mm Case fans x5

IMO if it works and is faster then go the 0.5 multi
after all, it's the speed that matters