Best ram for AMD platform

[BeepBeep2]

Just like ADATA Hyper XPG+ kits were...

Loose binning, so your kit might need 1.5v to do rated specification while another might barely do it at 1.8.

[konlaos]

Adata2000G v.2 @2133C7
Prime95 blend test (2Hr. 44min.)

Thanks: Ro ฝากรูป


sorry for my picture , it loading slowly

[Leeghoofd]

nice clocks, but wouldn't it have been cheaper to go straight for decent PSC kit ?

[konlaos]

and LinX

Thanks: Ro ฝากรูป

[Judge13]

Patriot Viper II Sector 5 2250 9-9-9-27 (PVV34G2250LLK) Elpida MGH-E, 1.72v
Pre- test...

[BeepBeep2]

Patriot Viper II Sector 5 2250 9-9-9-27 (PVV34G2250LLK)
Pre- test...

Unfortunately that's probably as far as your test will get...

[liberato87]

Patriot Viper II Sector 5 2250 9-9-9-27 (PVV34G2250LLK)
Pre- test...

voltages?
ram, cpu-nb?
thank you

[FlawleZ]

Patriot Viper II Sector 5 2250 9-9-9-27 (PVV34G2250LLK)
Pre- test...

Not trying to hate, but why is your SP1 efficiency SO poor? That score just seems way too slow for 3760Mhz.

[Formula350]

Not trying to hate, but why is your SP1 efficiency SO poor? That score just seems way too slow for 3760Mhz.

The one site I had read a few months ago, along with a spreadsheet with DDR3 overclocks showed SP1 as taking out a fair chunk of bandwidth. However, and I could be blind, but I don't see where it says he IS running SP1 :\ Unless you meant SPi, as in SuperPi...


I tried talking G.Skill into releasing a new kit for the AMD FX series... don't think they went for it lol
Ripjaws FX Series.jpg

[hiwa]

the new memories from GSKILL for AMD have F and X , but they aren't ripjaws

[Formula350]

the new memories from GSKILL for AMD have F and X , but they aren't ripjaws

For what secrets doth thee know, oh wise one?? I beggeth thee, good sir, to spill thy beans of knowledge!! lol

Are they Flare FX?! :O That'd be awesome lol DAMMIT! Now I've got an itch to pshop a stick of Flare

[Highgertz]

A bit of a rare set G. SKill Flare 4GB Kit DDR3 14400 CL7 8-7-24 1.65v, strips were taken 4х2GB, twin whales.
The first sets were released on ELPIDA MGH-E HYPER, then went to the PSC (Powerchip Semiconductor Corporation)






For lack of a platform for AMD, has been tested on BIOSTAR TP67XE.
Profiles written into SPD.



Starting at the same timings failed, had to raise trcd unit above is not clearly Elpida ...: scratch:
Omit samples and search for stable frequency / timings as that found for super pi 32m is 2133MHz CL6 9-7-24 1.68v.



The highest incidence was unable to determine because of the weak bus in the processor. It is clear that AMD will reveal quite memory

And for a snack, something that inevitably would have to do



These strips on Asus Crosshair IV running 6-6-6-21 bei 1800 MHz 1.65V

Let's wait for this set of tests Judge13

[reisya]

my Eco vdimm 1,65v



more and max push at same vdimm



i bet can reach timing Flare @2000Mhz but i can't got stable

[Formula350]

my Eco vdimm 1,65v

more and max push at same vdimm



i bet can reach timing Flare @2000Mhz but i can't got stable

Try upping your CPU-NB voltage to 1.325V (if it's not) and your actual NB chip voltage by +0.1V to +0.2V above your default. Alternatively you might need to change the Command Rate to 2T.

I think that 980MHz is pretty damn good either way though

[reisya]

Try upping your CPU-NB voltage to 1.325V (if it's not) and your actual NB chip voltage by +0.1V to +0.2V above your default. Alternatively you might need to change the Command Rate to 2T.

I think that 980MHz is pretty damn good either way though

1,325v
i think it's too high for thuban, NB chip i set +0,1V above default btw thanks for you tips

[Tomasis]

please run 32m and see how far it can go regarding Eco.

I ordered 2133 cl9 Gskill 2x4 and will compare it with eco :p I Too bad 2133 cl7 is sold out for 4gb though it'd be funnier to test 16gb for OC in future

[Formula350]

1,325v
i think it's too high for thuban, NB chip i set +0,1V above default btw thanks for you tips

My understanding was 1.45V was the max on high-end Air heatsinks. Either way, 1.35V is perfectly safe for a few minutes of testing to figure out what the deal is with the clocks.

[BeepBeep2]

Deneb before week 15 2010 - up to 1.4v should be safe 24/7 after that follow thuban.
Thuban - keep it around 1.35v.

[sponge bob]

best ram for buldozer ? i cant get any to work over 1333 on my BD setup

[mav2000]

What have you used till now?

[Leeghoofd]

best ram for buldozer ? i cant get any to work over 1333 on my BD setup

Everything worked here : powerchips, hypers, hynix, from 4 to 16Gb, 1600 over 2400Mhz... I think there's another issue somewhere...

Easiest for me where my RipjawsX 2133CL9, worked fine at 2400Mhz CL9 at 1.7Vdimm. Hypers needed some work...

[saint19]

best ram for buldozer ? i cant get any to work over 1333 on my BD setup

Corsair, G.Skill...skip Crucial.

[Riska]

Here is my FX-8150 with my Corsair Dominator GT-1600mhz 6-6-6-20 hypers from my X58 setup

[duron]

any effect if for tRAS & tRC if both is below18?

[BeepBeep2]

any effect if for tRAS & tRC if both is below18?

tRC =11, easier on Thuban IMC = sometimes more ram clock to offset bandwidth losses. chew* described it as your heart skipping a beat, it won't kill you but its not optimal for efficiency. Keep it at tRCD+tRAS.
As far as tRAS goes, on Hypers above 1800 Mhz you MUST slacken to 17 in most cases, my ram definately didn't pull 15 much over 1600. I could run 17 until 1900 though. It will continue to need slackened as Mhz increases.

I would have to guess that Riska is up in 1.85v-1.9v land with his sticks. My STT 2000 C7 needed 1.91v to validate 2022 Mhz CL6-6-6 on Thuban. My kit is a little better than average Corsair 1600 C6 looking at other results.