***Official***Z68X/P67A-UD7 Club/Discussion/Info**

[dinos22]

XP is strong

did 178K with lower CPU and GPU clocks

both x16 (yes more cpu but gains mostly from gt4)

[nijel]

...
Anyway someone can indicate to me how use Dynamic Vid ? set to normal and then ? how work this value, it's SVID +0.20 voltage or Stock +0.xx or need use - 0.xx ) Don't want to come with 2Vcore or try boot with 0.4V.

SVID + or - DVID depending the LLC level. Usually + on Standard, - on Level1, -- on Level2. Test for 100% load and you will find the best DVID value for your setup. Recommending to test 0-100% load range with the DVID you settle on.

[Lanek]

SVID + or - DVID depending the LLC level. Usually + on Standard, - on Level1, -- on Level2. Test for 100% load and you will find the best DVID value for your setup. Recommending to test 0-100% load range with the DVID you settle on.

Allright thanks a lot nijel .

[OC Nub]

XP is strong

did 178K with lower CPU and GPU clocks

Nice scores

I need to try a 580, they score strong.

[Falkentyne]

I believe my board do it by itself, each time i push to far, freeze in 3Dmark11, reboot i got a niiice " Checksum error, can't load HPA, ..." reflash with backup bios ( 3third times tonight in 1 hour, )... ( sometimes even without OC )

What i have find is flash using @bios, then reflash using Qflash with the same new bios ( F7e or f ) ... look like it stabilise a bit the thing about this " auto reflash " .

If someone have a fix for this will be good ..

Anyway someone can indicate to me how use Dynamic Vid ? set to normal and then ? how work this value, it's SVID +0.20 voltage or Stock +0.xx or need use - 0.xx ) Don't want to come with 2Vcore or try boot with 0.4V.

Did you flash the backup BIOS with alt-f12?

[GLENBOY]

as above lane if you flash the backup bios to f6x and use f7e i'd say , it very rarely tries to flash to backup then , these i would say are the best bioses and as dinos says if it reboots and you notice its gone back to the old bios switch off psu then when turned on it lets you back into the normal bios

alt f12 on bootup then it says flashing backup bios

[Eldonko]

Anyone know how I get 58x on this board? Max is 57x

[jackbrennan2008]

Anyone know how I get 58x on this board? Max is 57x

as far as i understand it 57x is intels max multi for these chips. you would have to set a multi of 57x then overclock the bclk

[3oh6]

as far as i understand it 57x is intels max multi for these chips. you would have to set a multi of 57x then overclock the bclk

57X is definitely not the max...a few 58X and 59X chips out there already.

looks like a BIOS update with that adjusted needs to happen

[Eldonko]

yeah other boards have higher, ud7 has 57x

[dinos22]

I uploaded a new bios for you on HWbot forum you asked at, it goes up to 59x

Anyone know how I get 58x on this board? Max is 57x

LINK

[stasio]

Thanks Dino!

[Nostromo]

Bah

[jackbrennan2008]

Ah nice . Anyone able to boot at 57-58x though. I can't get mine stable at 56x, it boots and shows 5.6Ghz at the POST screen, but then it crashes a few seconds later .

How is F8x going for everyone in terms of overclocking?

[andressergio]

Guys

I have a GIGA X58A UD3R with RAID0 x Samsungs F3's 1TB, will the GIGA P67A UD7 regognize my raid0 on the intel ports ? i know the bug but well i will give a shot

thanks !
Sergio

[cowie]

XP is strong

did 178K with lower CPU and GPU clocks

so the slots were worth 5-6k

[dinos22]

i dont know cowie i am suspecting its XP related mate

will test on UD5 again

[jbkappirossi]

Guys

I have a GIGA X58A UD3R with RAID0 x Samsungs F3's 1TB, will the GIGA P67A UD7 regognize my raid0 on the intel ports ? i know the bug but well i will give a shot

thanks !
Sergio

I've had my two f3 502hj's on my previous X58a-UD7.
And yes that wil work! But only on the Sata-300 port.
It cost me a full day to get my pre installed raid0 setup to boot.
I think its the first F3 Bios that gives trouble whit PCH 600 and Marvel.
I was getting; boot failure, missing HDD, Error, and a bunch of other BLa Bla's.
Because of the bug i dident try the 300 controller but after words that's the only one that works.


question, i had my set running previously on valueram 1333, because my 1866 i ordert was delayed.
And the thing is, that when overclock through turbo, say 45x100=4500 it clocks back to 1600mhz idle.
But when i set SPD on 18.66 wit the same turbo overclock it stays on 4500 and won't clock back to 1600mhz.
Is that because VID only works whit 1333 ?

[thebanik]

i dont know cowie i am suspecting its XP related mate

will test on UD5 again

Edited : must have been smoking weed.

[Eldonko]

Thanks bro. Still has PLL Overvoltage right?

I uploaded a new bios for you on HWbot forum you asked at, it goes up to 59x

LINK

[Lanek]

I uploaded a new bios for you on HWbot forum you asked at, it goes up to 59x



LINK

Dinos have something like a 6th sense, someone ask about 57+ multi, and hop a bios.

@Glenboy: yop thanks dude, will give a try, hoping it's not related to the problem you and cowie have got .

Did you flash the backup BIOS with alt-f12?

Not yet. I flash with the new one using @bios, then reflash with Qflash at start up.

[andressergio]

I've had my two f3 502hj's on my previous X58a-UD7.
And yes that wil work! But only on the Sata-300 port.
It cost me a full day to get my pre installed raid0 setup to boot.
I think its the first F3 Bios that gives trouble whit PCH 600 and Marvel.
I was getting; boot failure, missing HDD, Error, and a bunch of other BLa Bla's.
Because of the bug i dident try the 300 controller but after words that's the only one that works.


question, i had my set running previously on valueram 1333, because my 1866 i ordert was delayed.
And the thing is, that when overclock through turbo, say 45x100=4500 it clocks back to 1600mhz idle.
But when i set SPD on 18.66 wit the same turbo overclock it stays on 4500 and won't clock back to 1600mhz.
Is that because VID only works whit 1333 ?

thanks man mine aint bootable i have data only there

cheers !
Sergio

[Lanek]

Thanks bro. Still has PLL Overvoltage right?

yes it is ... look really good this bios, so far no problem boot well at any settings i have try so far ..

I believe some of my concern for voltage was coming from F7f.

[Eldonko]

Great thanks, I'll flash and test tonight.

[Lanek]

I have boot in windows without error with 51-52-53-54x ...

Still no crash in windows as i post right now with 5415mhz ... best bios for me so far.




definitevely like this bios, have find a good sweet spot temp vcore at 5100mhz stable for 24/7 ... enough don't need more ( outside for benching )