***Official***Z68X/P67A-UD7 Club/Discussion/Info**

[maxxx]

I would take down blck like already said, or i would check your temperatures. When i had a clodbug problem that was my stop code. That can also indicate not enough vcore, or cpu pll not right(increase/decrease) you might need to increase cpupll try 1.89 first. Also i know this applies to the UD4 you need to use turbo mode and enable tdp and tdc to 300, idk if you have to do this on the UD&, I am going to test it would, but on other boards it seems to keep back max oc.

@sin0822: thanks for the reply mate. I am trying the bclock route but once I go over 54x100 (eg. 54x101), I get that "4E" error. I don't think heat is my problem as its running on a custom Boreas (TEC). Let me try those settings from the UD4. Crossing fingers...

[sin0822]

yea what stasio says do not OC with turbo. Just set ratio instead.

[sin0822]

yea what stasio says do not OC with turbo. Just set ratio instead. and you can also just enable ratio change in OS and it will disable Turbo Mode

[Lsdmeasap]

I finally got it to work, reinstalled it again and it seems to work ok. Unfortunately I have no clue what was causing the problem.

Hope you are able to get it working.


@the real 7, glad you are enjoying your new toy.

Are you 100% sure that you didn't do anything else, or change or install anything?

I've been through 7-8 easytune versions, 3 versions of win7 or more, 2 vista setups, XP, and even and old RC 7100 Win7 build, all with the exact same look and issue in easytune.

[OC Nub]

I cant think of anything I changed or did any different other than uninstall, and reinstall et6. If I find that is was something else I will let you know asap, I hate when something doesnt work like it should also.

[ProStreetCamaro]

My BCLK wont show up either. If i move the curser across it i get the arrows pointing left and right but that is it. I have tried 2 versions and both the same.

[maxxx]

CPU Clock Ratio .......................................[ 55
Internal CPU PLL Overvoltage...........................[ Enabled
Real Time Ratio Changes In OS .........................[ Disabled
Intel(R) Turbo Boost Tech .............................[ Enabled
Turbo Ratio (Core 1)...................................[ Auto
Turbo Ratio (Core 2)...................................[ Auto
Turbo Ratio (Core 3)...................................[ Auto
Turbo Ratio (Core 4)...................................[ Auto
Turbo Power Limit (Watts)..............................[ 100
Turbo Current Limit (Amps).............................[ 100
CPU Cores Enabled ............................ ........[ All
CPU Multi Threading....................................[ Enabled
CPU Enhanced Halt (C1E) ...............................[ Disabled
C3/C6 State Support ...................................[ Disabled
CPU Thermal Monitor ...................................[ Disabled
CPU EIST Function .....................................[ Disabled
Bi-Directional PROCHOT ................................[ Disabled

I am guessing the TDP/TDC are those I have highlighted. Still a no go. Should those settings be higher that 100? CPU PLL set to 1.90v. That 4E thing must be really a wall inside the SB. Does other boards have this same problem? Or its called something else?

[Lsdmeasap]

I cant think of anything I changed or did any different other than uninstall, and reinstall et6. If I find that is was something else I will let you know asap, I hate when something doesnt work like it should also.

Yes, if you can think of anything, or cause it to be gone then re-appear again let me know how.

My BCLK wont show up either. If i move the curser across it i get the arrows pointing left and right but that is it. I have tried 2 versions and both the same.

Thanks, and sorry , but I'm glad I'm not alone on this still as that makes it harder to diagnose or try to get help with.

I am sending in a report to Taiwan now to see if the BIOS guys or software team have ran into this issue in the past and can maybe tell us what is causing it or how to fix it.

I'll keep you posted on what they have to say.

[stasio]

maxxx,did you try with "Turbo Boost" Disabled?
I never Enable this over 4.8GHz.

yea what stasio says do not OC with turbo. Just set ratio instead. and you can also just enable ratio change in OS and it will disable Turbo Mode

As my memory is not compatible with P67(yet?),I start with Standard and CR on Auto(2),then if pass 32M,try with Turbo(CR2),then Standard/CR1,etc...
atm,
5GHz,1876 7-7-7-21-CR1/Turbo(32M ok)
(Wish to have new Ripjaws-X F3-17066CL8D-4GBXMD or F3-17000CL7D-4GBXHD)

[maxxx]

maxxx,did you try with "Turbo Boost" Disabled?
I never Enable this over 4.8GHz.

@stasio: yup, I dun enabled this when I overclock, but I needed to access the TDP/TDC settings to test. If Turbo is disabled, they are greyed out and can't access them. I want/need to get over that 4E error. Btw, know if there are other batches for the 2600k in KL?

About ET6, same boat as the rest, can't change the bclock setting. On bios F7e.

[stasio]

@stasio: yup, I dun enabled this when I overclock, but I needed to access the TDP/TDC settings to test. If Turbo is disabled, they are greyed out and can't access them. I want/need to get over that 4E error. Btw, know if there are other batches for the 2600k in KL?

About ET6, same boat as the rest, can't change the bclock setting. On bios F7e.

New batches for the 2600K in KL(all out of stock),coming end of this month.

[Lsdmeasap]

About ET6, same boat as the rest, can't change the bclock setting. On bios F7e.

Thanks! As I mentioned before I bet there are plenty of people that cannot adjust Bclk via Easytune out there, they just don't know it yet because without the setting there you don't realize your missing anything until you see someone mention it.

I didn't know for a week or so, and just assumed it was not added to easytune because you can't adjust Bclk much anyway, but then I saw someone mention getting 3-4 more Bclk past what they set in the BIOS with easytune.

[dinos22]

strange stuff this bclock business, lets see what software guys have to say

[Lsdmeasap]

Ya, it is very odd how it works fine for some but not others!

Hopefully they can figure it out for us.

[TheHardCase]

Running real smooth @ 5Ghz
100% Stable can't get any better.
100% load max temp 74c

I'll also show a pic of my setup...





### MB Intelligent Tweaker ###

Advanced Frequency Settings:

CPU Clock Ratio .......................................[ 50

> Advanced CPU Core Features

CPU Clock Ratio .......................................[ 50
Internal CPU PLL Overvoltage...........................[ Enabled
Real Time Ratio Changes In OS .........................[ Disabled
Intel(R) Turbo Boost Tech .............................[ Disabled
Turbo Ratio (Core 1)...................................[ Auto
Turbo Ratio (Core 2)...................................[ Auto
Turbo Ratio (Core 3)...................................[ Auto
Turbo Ratio (Core 4)...................................[ Auto
Turbo Power Limit (Watts)..............................[ Auto
Turbo Current Limit (Amps).............................[ Auto
CPU Cores Enabled ............................ ........[ All
CPU Multi Threading....................................[ Enabled
CPU Enhanced Halt (C1E) ...............................[ Disabled
C3/C6 State Support ...................................[ Disabled
CPU Thermal Monitor ...................................[ Disabled
CPU EIST Function .....................................[ Disabled
Bi-Directional PROCHOT ................................[ Disabled

<

BCLK/DMI/PEG Clock Control ............................[ Enabled
BCLK/DMI/PEG Frequency Control ........................[ 1002
System Memory Multiplier (SPD) ........................[ 18.66

Advanced Memory Settings:

System Memory Multiplier (SPD) ........................[ 18.66
Performance Enhance ...................................[ Standard
DRAM Timing Selectable (SPD) ..........................[ Quick
Channel Interleaving ..................................[ Enabled
Rank Interleaving .....................................[ Enabled



Advanced Voltage Control:

CPU

Load Line Calibration .................................[ Level 2
CPU Vcore .............................................[ 1.48
QPI/VTT Voltage 1.050v ................................[ 1.1
System Agent Voltage 0.925v ...........................[ 1.250
PCH Core 1.050v .......................................[ 1.050
CPU PLL 1.800v ........................................[ 1.80

DRAM

DRAM Voltage 1.500v ...................................[ 1.66
DRAM Vref 0.750v ......................................[ Auto
DRAM Termination 0.750v ...............................[ Auto
Ch-A Data VRef. 0.750v ................................[ Auto
Ch-B Data VRef. 0.750v ................................[ Auto
Ch-A Address VRef. 0.750v .............................[ Auto
Ch-B Address VRef. 0.750v .............................[ Auto

Miscellaneous Settings

Isochronous Support ...................................[ Disabled
Virtualization Technology .............................[ Disabled

[the_real_7]

Running real smooth @ 5Ghz
100% Stable can't get any better.
100% load max temp 74c

I'll also show a pic of my setup...





### MB Intelligent Tweaker ###

Advanced Frequency Settings:

CPU Clock Ratio .......................................[ 50

> Advanced CPU Core Features

CPU Clock Ratio .......................................[ 50
Internal CPU PLL Overvoltage...........................[ Enabled
Real Time Ratio Changes In OS .........................[ Disabled
Intel(R) Turbo Boost Tech .............................[ Disabled
Turbo Ratio (Core 1)...................................[ Auto
Turbo Ratio (Core 2)...................................[ Auto
Turbo Ratio (Core 3)...................................[ Auto
Turbo Ratio (Core 4)...................................[ Auto
Turbo Power Limit (Watts)..............................[ Auto
Turbo Current Limit (Amps).............................[ Auto
CPU Cores Enabled ............................ ........[ All
CPU Multi Threading....................................[ Enabled
CPU Enhanced Halt (C1E) ...............................[ Disabled
C3/C6 State Support ...................................[ Disabled
CPU Thermal Monitor ...................................[ Disabled
CPU EIST Function .....................................[ Disabled
Bi-Directional PROCHOT ................................[ Disabled

<

BCLK/DMI/PEG Clock Control ............................[ Enabled
BCLK/DMI/PEG Frequency Control ........................[ 1002
System Memory Multiplier (SPD) ........................[ 18.66

Advanced Memory Settings:

System Memory Multiplier (SPD) ........................[ 18.66
Performance Enhance ...................................[ Standard
DRAM Timing Selectable (SPD) ..........................[ Quick
Channel Interleaving ..................................[ Enabled
Rank Interleaving .....................................[ Enabled



Advanced Voltage Control:

CPU

Load Line Calibration .................................[ Level 2
CPU Vcore .............................................[ 1.48
QPI/VTT Voltage 1.050v ................................[ 1.1
System Agent Voltage 0.925v ...........................[ 1.250
PCH Core 1.050v .......................................[ 1.050
CPU PLL 1.800v ........................................[ 1.80

DRAM

DRAM Voltage 1.500v ...................................[ 1.66
DRAM Vref 0.750v ......................................[ Auto
DRAM Termination 0.750v ...............................[ Auto
Ch-A Data VRef. 0.750v ................................[ Auto
Ch-B Data VRef. 0.750v ................................[ Auto
Ch-A Address VRef. 0.750v .............................[ Auto
Ch-B Address VRef. 0.750v .............................[ Auto

Miscellaneous Settings

Isochronous Support ...................................[ Disabled
Virtualization Technology .............................[ Disabled

Nice with a little push on you vdimm 1.66 and why you push System Agent Voltage ?

[the_real_7]

strange stuff this bclock business, lets see what software guys have to say

software threw BIOS has never been definite always glitchy , now more than ever cause giga worries about quality in board first , and works out glitches later
itll be fine giga always come thru

[Lsdmeasap]

Hope that can fix it before 8 days from now!

You are right though, they will get it sorted out for sure!

[the_real_7]

Hope that can fix it before 8 days from now!

You are right though, they will get it sorted out for sure!

well i cant guarantee 8 days . . . but i can tell you giga updated a bored that been out a year already threw BIOS and drivers EP45-UDP3 " FFb 0.70 MB 2010/10/06 " where in good shape " giga takes care of business

[Lsdmeasap]

Ya I know they take care of business for sure!

I am in contact with them often

[the_real_7]

Ya I know they take care of business for sure!

I am in contact with them often

if you are Lsdmeasap please tell them. this long 3 bootloop on bios mistakes needs help

[sin0822]

the bootloop is common on other GB boards, its the BIOS checking and rechecking itself. When the OC fails and then bootloops that is really annoying because it should reset, but sometimes fails to reset the OC. I am surprised you were able to change blck through windows OC Nub, i have no luck with it, i actually thought you have to reboot to change blck, and it isn't possible through windows, but who knows.

[the_real_7]

the bootloop is common on other GB boards, its the BIOS checking and rechecking itself. When the OC fails and then bootloops that is really annoying because it should reset, but sometimes fails to reset the OC. I am surprised you were able to change blck through windows OC Nub, i have no luck with it, i actually thought you have to reboot to change blck, and it isn't possible through windows, but who knows.

before we had a normal reboot , but this one take 2 the time and erases my xfi setings . . . why you think ?

[OC Nub]

the bootloop is common on other GB boards, its the BIOS checking and rechecking itself. When the OC fails and then bootloops that is really annoying because it should reset, but sometimes fails to reset the OC. I am surprised you were able to change blck through windows OC Nub, i have no luck with it, i actually thought you have to reboot to change blck, and it isn't possible through windows, but who knows.

It asks you to restart, click restart later, the changes to bclk will be applied right away when you click "set", they will also be applied on restart.

[jackbrennan2008]

Ok i think i have found the maximum for my board without putting the PLL voltage over 1.96 and the vcore over 1.555v with LLC Level 2.
5523.84Mhz



http://valid.canardpc.com/show_oc.php?id=1611255

I've printed out that template so i'll note down my settings when i get that done!

Wprime run:


Super PI 1M - I forgot to sleect the memory tab . 9-9-9-24 1T 937Mhz


3DMark 2001 SE